Craftsman 9-29012 Bedienungsanleitung

SFo_u_h_'_e"_r"unle_

SWA/_S

owner's

manual

CATALOG NO.

9-29012

9-29013

FITSTHE FOLLOWING

MODEL NUMBERS:

113.197110, 113.197111

113.197150, 113.197151

113.197210, 113.197211

113.197250, 113_197251

113.197410, 113.197411

113.197510, 113.197511

113.197610, 113.197611

113.197180, 113.197181

FOR YOUR

SAFETY:

SEA/A_S/I:RRFT$MgN_

10-INCH RADIAL SAW

GUARD KIT

• assembly

• operating

• repair parts

READ ALL

INSTRUCTIONS

CAREFULLY

Sold by SEARS, ROEBUCK AND CO., Chicago, IL 60684 U.S.A.

Part No. SP5623 Printed in USA

Table of Contents

Section Title ................................................................................ Page

Safety ........................................................................................................................ 3

Assembly .................................................................................................................. 8

Repair Parts ............................................................................................................ 17

iiillllllllllllllllll ii ii ............................

FULL ONE YEAR WARRANTY ON CRAFTSMAN RADIAL ARM SAW GUARD KIT

If within one year from the date of purchase, this Craftsman Radial Saw Guard

Kit fails due to a defect in material or workmanship, Sears will repair it, free of

charge.

WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE

NEAREST SEARS SERVICE CENTER/DEPARTMENT THROUGHOUT THE

UNITED STATES.

This warranty applies only while this product is used in the United States.

This warranty gives you specific legal rights and you may also have other rights

which vary from state to state.

SEARS, ROEBUCK AND CO. D/817 WA

Hoffman Estates, IL 60195

iiiiii, i1,1 ii1,111 iiiii ,i ii i i i,iii1,1111,1,11,ii, i,,i

Safety

This manual has safety information and

ins_ctions to help users eliminate or reduce

the risk of accidents and injuries, including:

1. Severe cuts, and loss of fingers or other

body parts due to contact with the blade.

2. Eye impact injuries, and blindness, from

being hit by a thrown workpiece, workpiece

chips or pieces of blade,

3. Bodily impact injuries, broken bones, and

internal organ damage from being hit by a

thrown workpiece

4. Shock or electrocution

5. Bums.

Major Hazards

Three major hazards are associated with

using the radial arm saw for ripping, They

are ouffeed zone hazard, kickback, and

wrong way feed.

This section only briefly explains these haz-

ards. Read the ripping and crosscutting safe-

ty sections of your saw manual for more

detailed explanations of these and other haz-

ards.

Outfeed Zone Hazard

,i_t,DANGER

Safety Symbol and Signal Words

An exclamation mark inside a triangle is the

safety alert symbol.

It is used to draw attention to safety informa-

tion in the manual and on the saw_ It is

followed by a signal word, DANGER,

WARNING, or CAUTION, which tells the

level of risk:

,_ DANGER: means if the safety infor-

mation is not followed someone will be seri-

ously injured or killed.

WARNING: means if the safety infor-

mation is not followed someone could be

seriously injured or killed.

,,Ik

,_ CAUTION: means if the safety infor-

mation is not followed someone might be

injured.

Read and follow all safety information

and instructions.

If you reach around the blade to the outfeed

side when ripping, and try to hold down or

pull the workpiece through to complete a

cut, the rotational force of the blade will pull

your hand back into the blade.

Fingers will be cut off.

Safety

Kickback Hazard

Kickback is the uncontrolled p_opelling of

the workpiece back toward the user' during

ripping°

The cause of kickback is the binding or

pinching of the blade in the workpiece°

Several conditions can cause the blade to

bind or pinch.

When a workpiece kicks back, it could hit

hard enough to cause internal organ injury,

broken bones, or death.

kWARNING

KICKBACKII

Wrong Way Feed Hazard

Wrong way feed is ripping by feeding the

workpiece into the outfeed side of the blade.

The rotational force of the blade can grab

and pull the workpiece.

Before you can let go or pull back, the force

could pull your hand along with the work-

piece into the blade. Fingers or hand could

be cut off.

The propelled workpiece could hit a by-

stander, causing severe impact injury or

death_

kWARNING

Wrong Way Feed

Safety Instructions

Read and follow all safety instructions,

Personal Safety Instructions

1. Wear"safety goggles labeled "ANSI

Z87.1" on the package, tt means the goggles

meet impact standards set by the American

National Standards Institute. Regular eye-

glasses are not safety goggles.

2. Wear close fitting clothes, short sleeved

shirts, and non-slip shoes. Tie up long hair.

Do not wear gloves, ties, .jewelry, loose

clothing, or long sleeves. These can get

caught in the spinning blade and pull body

parts into dae blade.

3. Wear dust mask to keep from inhaling

fine particles.

4. Wear ear protectors, plugs or muffs if' you

use saw daily.

5. Keep good fboting and balance; do not

over-reach.

Work Area Safety Instructions

1. Keep children, pets, and visitors out of

work area; they could be tilt by a thrown

workpiece, workpiece chips or pieces of

blade.

2. Turn saw off, remove yellow key, and

unplug before leaving work area. Do not

leave until blade has stopped spinning.

3. Make work area child-proof: remove yel-

low key to prevent accidental start-up; store

key out of sight and reach; lock work area.

4. Keep floors clean and flee of sawdust,

wax and other slippery materials.

5. Keep work area well lighted and unclut-

tered,

6. Use saw only in dry area. Do not use in

wet or damp areas.

Dust Mask

Ear Proleclors

Safety

Saw Safety Instructions

1_Use guard, pawls and riving knife accord-

ing to instructions. Keep them in working

order.

2_Routinely check saw for broken or dam-

aged parts. Repair or replace damaged parts

before using saw. Check new or rep_ed

parts fbr alignment, binding, and correct

installation.

3. Unplug saw before doing maintenance,

making adjustments, correcting alignment,

or changing blades.

4. Do not force saw. Use saw, blades and

accessories only as intended.

5. Have yellow key out and saw switched off

before plugging in power cord.

6. Before turning on saw, clear table of all

objects except workpiece to be cut and nec-

essary fixtures, clamps, or feather-boardso

7. If blade jams, turn saw off immediately,

remove yellow key, the free blade. Do not

try to free blade with saw on.

8_Turn saw off if it vibrates too much or

makes an odd sound° CorT_t any problem

before restarting saw.

9. Do not layout, assemble, or setup work

with saw on, or while blade is spinning.

10. Keep saw table clean.

11. Store items away from saw. Do not

climb on saw or stand on saw table to reach

items because saw can tip over.

Workpiece Safety Instructions

!. Cut only wood, woodlike or plastic mate-

rials.. Do not cut met'_

2. Cut only one workpiece at a time.

Stacking or placing workpieces edge to edge

can cause user to lose control of workpieceo

Safety

3. Rip only workpieces longer than the

diameter of the blade. Do not rip workpieces

that are shorter than the diameter of the

blade being used.

4. Workpieces that extend beyond the saw

table can shift, twist, rise up from the table,

or fall as they ar'e cut or afterwards. Support

workpiece with table extensions the same

height as the saw table.

5. To prevent tipping, support outer ends of

extensions with sturdy legs or an outrigger.

6. Do not use another person to help support

workpieces or to aid by pushing or pulling

on workpieces, because these actions can

cause kickback. Use table extensions.

7. Use clamps or vice to hold workpiece. It's

safer than using your hands.

Blade Safety Instructions

1.Use only blades marked for at least 3450

rpmo

2. Use only 10" or smaller diameter blades.

3. Use blades for their recommended cutting

procedures.

4. Keep blade sharp and clean.

5. Do not overtighten blade nut because

blade collar could warp°

6o Do not turn saw on and off in rapid

sequence because blade can loosen.

7. Blade should stop within 15 seconds after

saw is switched off. If blade takes longer, the

saw needs repair. Contact Sears Service

Center.

Assembly

Identify Parts

3he h_!lowing paris are inchided:

Nole: B@nv beginning assembl3; check that all parts are included If you ate missing at O, part, do

m_t assemble guar_L _mtact your Sear_ Service Center to get the missing part. Sonlethnes snlall

parts can get lost in packaging material. Do not throw away any packaging until guar'd is put

toRethet: Check packaging for' missing palts bcjbre contacting Sears, A COnlplete parts list (Repair

Parts) is at the end oJ the nlanual. Use the list to identij], the nuntber of the missblg part.

IJst of hmse parts with catalog #9-29012

A_ Guard Assembly ................. I

B Rear Table 40" ......................I

C SpacerT_d_Ic 40". ..................1

D. Izront Fable 40" .....................I

ETahte Supporl ........................2

I;. Handle Assembly ................ 1

G. Bag Ol Loose Parts ........... I

Conlaining:

II,.Adapter Motor Key ........... I

I Screw Pan lid Ty T

6-32 x 1/2 ............................... 1

l Screw Flal Hd Plaslite

#1() x 3/4 ............................... 2

Kfi2e Nu| ................................. I

l. Bag Ol Loose Paris ................ 1

Conlaining:

M, Guard Accessory ................ I

No Screw Plaslile #8 x 1/2 ...... 1

O. Washer 3/t6 x I x 1116....... 1

P, Owners Manual ................. 1

lJst of hmse parts with catalog #9-29013

A, Guard Assembly ................. 1

BRear T_tble 44" ................... 1

C, Spacer Table 44" ................. 1

I), Front Table 44" .................. l

I;. tlandte Assembly .............. 1

G Bag Ol Loose Parts ............ 1

Conlaining:

I1, Adapter Motor Key ............. 1

1 Screw Pan Hd Ty T

6-32 x I/2 .............................. t

l Screw Flat Hd Plastile

#1() x 3/4 .............................. 2

K Iixe Nut .....................................t

l_Bag Ol: l_oose Paris .............. 1

Containing:

M, Guard Accessory ................ I

N Sc_cw Plaslite #8 x 1/2 ...... 1

() Washer 3116 x I x 1/16 ....... 1

P, ()whets Mamml ......................t

dK_ N

Assembly

Guard Installation Steps

1. Remove existing table boards. Keep all

screws, nuts and washers, including the lev-

elling screws in the center of the front table.

Discard the old table boards but keep the

fence.

2o 40" TABLE ONLY (if you have the 44"

table, skip to next step):

- Remove the table support channels,

keeping the screws, nuts and washers°

Discard the old channels.

- Install the new support channels.

- Referring to your saw owners manual,

level the channels and tighten them in

place.

Install the tee nut into the front table

board.

Refering to your saw owners manua!,

install and level the table boards.

3.44" TABLE ONLY (if you have the 40"

table, skip to next step):

Position the flont table and insert the

front two screws. The rear screw holes

in the table do not line up on any holes

in the saw base,

Using the rear screw holes as a drill

guide, drill a .5/16" hole in the saw base

for each of the two rear screws.

Remove the front table.

The U-Clips that were used as nuts for

the rear screws must be moved to the

new screw location° Remove them

from the saw and reinstall them on the

holes you .just drilled,

Install the tee nut into the front table

board.

Referring to your saw owners manual,

install and level the table boards.

4, The saw's crosscut travel may no Ionger

be square. Referring to your saw owners

manual, square the crosscut tlavel.

.5. Remove the existing guard and blade.

Rotate the saw to the outrip position.

6, Elevate and rotate the saw to the 45

degree bevel position, Remove and discard

one of the handle retaining screws,

Note: This retro fit guard kit requires addi-

tional clearance behhM fence, New table

boards are being supplied for this reason,

.... I [-]

Handle

Retaining

Screw

Assembly

7, Rotate the saw to the negative 45 degree

l_'cx,_c!position. Remove and discmd ttle

oflmr lmndle retaining screw, Discard tile old

handle,

8. Using the two #1(1 x 3/4 flat head screws

provided, altach the new h;mdle in tile same

way as the old one was renloved,

9o Return lhe saw to the blade vertical, cross-

cut position.

10, Remove the top motor cover screw and

lock washer: Keep the washer, Discard the

old screw,

11, Install the adapter: Tile two ends of' tile

adapter fh into tile center cooling slots of the

motor; then the adapter is rotated tip into

phlce.

12. Install the replacement screw (#6 x 1/2")

with the old lock washer into the top motor

cover hole. This locks tile adapter in place.

13, Reinstall the blade°

Note: Tim rip scale fi_r the fi'ont fence posi-

tirol i._no longer cotvect Subtract 1-1/8"

fiom the ._'cale reading to obtain the correct

reading,

Install Guard

The guard is a very important safety feature_

It covers a large part of tile blade and helps

protect against severe cuts, Always use the

gumd.

1.Lock motor at 0°bevel (blade vertical).

2, Use one hand to lift cleaa" plastic guard;

use od_er hand to grasp fear of guard (below

dust elbow). Position guard so riving knife

fuces front of saw.

3oTilt fiont of guard down about 45°; place

over' blade; rotate guard to level position,

Nole: Make .uae notch in guardfits onto tab

on motor adapter. This wUlprevent move-

merit o/guard about motor Squeeze handle

u'igger to make sure it raises clear plas-tic

guard l[ it &_es ,tot, remove and re-install

gtuud, makiltg sure that trigger mechanism

engages pull link on guard,

-'LTighten guard clamp screw,

Motor Cover

Panel

Top Motor

Cover Screw

Parallel

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Craftsman Gesehen Handbücher

Craftsman

Craftsman 315.21213 Bedienungsanleitung

Craftsman

Craftsman 137.212371 Bedienungsanleitung

Craftsman

Craftsman 315.243000 Bedienungsanleitung

Craftsman

Craftsman 320.28195 Bedienungsanleitung

Craftsman

Craftsman 315.113081 Bedienungsanleitung

Craftsman

Craftsman 21602 - 16 in. Variable Speed Scroll Saw Bedienungsanleitung

Craftsman

Craftsman 137.218240 Bedienungsanleitung

Craftsman

Craftsman 113.247110 Bedienungsanleitung

Craftsman

Craftsman 113.221740 Bedienungsanleitung

Craftsman

Craftsman 113.199410 Bedienungsanleitung

Craftsman

Craftsman 113.2945 Bedienungsanleitung

Craftsman

Craftsman 113.197110 Bedienungsanleitung

Craftsman

Craftsman 315.220381 Bedienungsanleitung

Craftsman

Craftsman 137.218020 Bedienungsanleitung

Craftsman

Craftsman 315.220380 Bedienungsanleitung

Craftsman

Craftsman 113.197511 Bedienungsanleitung

Craftsman

Craftsman 113.244513 Bedienungsanleitung

Craftsman

Craftsman 315.108420 Bedienungsanleitung

Craftsman

Craftsman 351.214610 Bedienungsanleitung

Craftsman

Craftsman 113.29921 Bedienungsanleitung

Craftsman

Craftsman 315.271080 Bedienungsanleitung

Craftsman

Craftsman 137.214130 Bedienungsanleitung

Craftsman

Craftsman 315.212300 Bedienungsanleitung

Craftsman

Craftsman 113.27521 Gebrauchs- und Pflegehandbuch

Beliebte Gesehen Handbücher anderer Marken

RIDGID

RIDGID BS1400 Bedienungsanleitung

ATIKA

ATIKA BWS 400-2 Bedienungsanleitung

RGC

RGC FS20 Bedienungsanleitung

Makita

Makita M2300 Bedienungsanleitung

IMET Spa

IMET Spa BASIC 300 PLUS SHI Bedienungsanleitung

IMET Spa

IMET Spa SIRIO 370 AF-E Bedienungsanleitung

Optimum

Optimum OPTisaw CS 275 Bedienungsanleitung

Makita

Makita BPB180 Bedienungsanleitung

Stihl

Stihl MS 462 C-M Bedienungsanleitung

AEG

AEG TS 250 K Bedienungsanleitung

Meec tools

Meec tools 004665 Bedienungsanleitung

Makita

Makita LS1018L Bedienungsanleitung

Ryobi

Ryobi RCS1400 Bedienungsanleitung

DeWalt

DeWalt DCS391 Bedienungsanleitung

Sealey

Sealey SA72 Bedienungsanleitung

skilsaw

skilsaw SPT88 Montageanleitung

Urrea

Urrea SI810 Abmessungen und Installationsanleitung

EINHELL

EINHELL BKG 210/1 Bedienungsanleitung