Createbot MAX Bedienungsanleitung
MAX3D Printer
Tel:0086-574-88037579
Scanning for more online Support
Instruction
Mini Packing List
MAX3D Printerx1
The items listed below are all the accessories in the box.Please check the items
before using
PLA Filament1kgx1
Door Plate x4 Filameant Support x1 or 2
Glass Platform(282x270mm)x1 Bladex1
Door Handlex1
Power Supply x1
USB Cablex1
SD Cardx1
Card Readerx1
Wrenchx3
(1.5/2/2.5)
Plastic Partsx2
Thumb screw(M3X6)x8
Screw (M4x6)x10
Circular magnets(12*6*1)x1
Bucklex8
1
Tweezersx1
Appearance Introduction
2
SD Slot
Touch Screen Printing Platform
Extruder
Load the filament
First fixed filament holder in the machine on the right side of the holder hole with four hand
screw screws , put the filament on the holder,insert filament from feed port of nozzle through
the white feed tube,stop insert until feel the resistance
White Pipe
Scroll
Feed port
Fliament Support 3
Operartion Guide
Step1
Taking out the three door plate,fix the left and right door plate on the printer with M4x6
screw.Then assemble the plastic parts and door handle with the M4x6 screw on front of the
printer.
Step2
First press the TOOL button into the tool menu then PREHEAT button you can see on
the picture 3
4
Turn on the Printer
Insert the power cable into the 220V power connector on the back of the machine and insert
the power cable into the wall power connector. Press the front round metal button on the
machine and hear the “di” sound. The display shows the startup interface, indicating that the
3D printer is normal start up.
22V Power Input
Power Cable
Home Page Preheat Menu
Light Button
Tool Button
Click “TOOL”, then choose “FILAMENT” and click “DOWN” to extrude the filament. If it is
extruded normally and smoothly, click “Stop” to finish it and click “BACK” to return to home
page.
Extruding Test
Step3
。
Step4
Clip of the glass platform 5
Well assembled
Direction of insert
Take out the glass platform from the box of accessories. Then push it until it reaches to the end of heated
bed. Finally, fix it with the glass clip in front of heated bed. (Please note: after installing the glass platform,
click “TOOL” and choose “LEVEL” to level the platform. Adjust the distance between nozzle and platform
to the thickness of one A4 paper by rotating the corresponding screw under the platform.)
Tool Menu Load and unload the filament
Step5
In the print home page, click the print icon, enter the print interface, open (openSD) icon,
open the SD card file interface, choose the 001 testing model ,then the printer will start
printing.
6
Printing Test
Now,you can already use createbot 3d printer,there are many interesting models on the website
WWW.China3Dprinter.cn for your download,besides you can also print any 3d models design by
yourself,createbot slice software support OBJ, STL, AMF and other formats of three-dimensional
model,the steps of install slice software as follows:
Slicing Software Installation
Copy the slicing software file from the SD card into your comoputer and Open the installer
Slicing Software
The software will insatll the drive automatically,click next to finish the installation
Select the path where the slice software is installed, then click Next, click
Install, the softwarewill automatically instaledl until finished
7
After the software is installed automatically, you will see the interface below, click the
Finish button, end the slice software installation.
The parameter settings for first run the
slice software
Open the slice software,select language,choose the model of the printer you purchased(such
as the purchase MINI, please select MINI), then click Next to complete the configuration.
8
Recommended using the following parameters to printing your models,you also can adjust
the parameters for your needs.
9
Picture1
Note:
When selecting a support type, it is possible to determine whether it is
necessary to add partial support or entire support or without support by
observing the model or slice interface. But in principle it is better to avoid
support or reduce support.Rotate model can be used to avoid or reduce the
purpose.
When selecting the type of platform attachment, the edge or grid can
be appropriately added according to the size of the land area and the height
of the model.
Single Extruder
Dual Extruder
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Createbot 3D-Drucker Handbücher
Createbot
Createbot Mini I Bedienungsanleitung
Createbot
Createbot MaxI Bedienungsanleitung
Createbot
Createbot MaxI Bedienungsanleitung
Createbot
Createbot R3D S1 Benutzerhandbuch
Createbot
Createbot Mini I Bedienungsanleitung
Createbot
Createbot S3 Bedienungsanleitung
Createbot
Createbot Super Mini Bedienungsanleitung
Createbot
Createbot MINI-Pro Bedienungsanleitung
