Creche Innovations MicroCool Bedienungsanleitung

Digital Lock for MicroCool™ Refrigerator

Station Mode Instructions

TableofContents

1. Warranty and Return Policy

2. Getting Started

3. Station Mode Programming Instructions

4. Double Digit Codes

5. Switching Modes

Please read this manual carefully before starting the machine. Keep it in a safe place for

future reference. If the device is resold, this manual

must be handed over to the

purchaser along with the device.

WarrantyandReturnPolicy

Creche Innovations warrants the MicroCool™ Digital Lock to be free from defect in

materials and workmanship for a period of two years from the date of shipment

to the user. If the product fails to perform in accordance with the product

specifications, Creche will repair or replace, at its option, the defective materials

or parts. Creche will pay customary freight charges from Creche to the customer

location only. This warranty does not cover damage caused by accident, misuse,

abuse, alteration and other defects not related to material or workmanship. To

exercise your rights under this warranty, contact Creche Innovations.

The user/owner must operate the equipment in strict accordance with the most

recent User Manual and any additional training or training materials provided

by Creche designated representatives.

The user/owner of this equipment shall have sole responsibility and liability for

any injury to person or damage to property resulting from: 1) Operation not in

accordance with supplied operating instructions, 2) Maintenance not in accordance

with authorized maintenance instructions, 3) Service by anyone other than a factory

authorized representative, 4) Modification of the equipment or accessories,

5) Use of damaged or unauthorized components and accessories and 6) Improper

installation.

GettingStarted

Program Button:

Initiate the lock programming mode by pressing the front thin edge of the black button

Inward toward the mounting surface the MicroCool™ Digital Lock is mounted to.

Infrared Receiver:

The Infrared Receiver will receive a signal from an electronic MicroCool™ Key Fob when

it is pointed at the receiver located behind the Program button. The Program button

is slightly opaque so the key-fob signal will penetrate the button.

Knob:

To move the lock mechanism 90 to 180 degrees clockwise or counterclockwise from the

lock and unlocked states

Multiple Levels of Access:

1. Master code and/or blue control key fob

2. Supervisor code and/or black key fob

3. User code and/or black key fob

The MicroCool™ Digital Lock is pre-programmed with a factory master code and factory

supervisor code.

Operation

1. Unlock with a code by entering a valid code. The green LED will illuminate

2. Turn the knob to unlock

3. To lock, turn the knob to align the knob pointer with the lock icon on the keypad.

The factory master code is: 135243

The factory supervisor code is: 123

StationModeProgrammingInstructions

** Make sure to write down all the new codes you create for future use.**

Change the Master Code (6 Digits) using the Factory Master Code

1. Push the black program button (located on the side of the lock) 5 times

2. Enter the factory master code (135243) 2times

3. Enter your new master code (must be 6 digits long) 2 times.

4. The lock will blink 6times to indicate that the factory master code was erased

and your new master code was accepted.

Change the Supervisor Code (3-6 Digits) using the Factory Supervisor Code

1. Push the black program button 1 time

2. Enter the factory supervisor code (123) 1 time

3. Enter your new supervisor code (must be 3-6 digits long) 1time

4. Push the black program button 1 time

5. The lock will blink 6times to indicate that the factory supervisor code was erased

and your new supervisor code was added.

Add a User Code (3-6 Digits) using the Supervisor Code

1. Push the black program button 2 times

2. Enter your supervisor code 1 time

3. Enter the new user code 1 time

4. Push the black program button 1 time

5. The lock will blink 6times to indicate that your supervisor code was used to add

the new user code

Change your current Master Code (6 Digits)

1. Push the black program button 5times

2. Enter old master code 2 times

3. Enter new master code 2times

4. The lock will blink 6times to indicate that old master code was erased and

new master code was accepted.

Change the Supervisor Code (3-6 Digits) Using a Supervisor Code

1. Push the black program button 1times

2. Enter old supervisor code 1 time

3. Enter new supervisor code 1time

4. Press the black program button 1 time

5. The lock will blink 6times to indicate that the old supervisor code was erased and

the new supervisor code was accepted

Remove the User Code Using the Supervisor Code

1. Push the black program button 2times

2. Enter the supervisor code

3. Enter 1 1 1 1 1

4. Press the black program button 1time

5. The lock will blink 6times to indicate that the supervisor code was used to remove

the user code. The user code will no longer be valid for access.

Add a Control Fob

1. Push the black program button 1time

2. Enter the master code

3. Point the control fob at the black program button and press the fob button

4. The lock will blink 6times to indicate that the master code was used to add a

control fob

Add a Supervisor Code (3-6 Digits) Using the Control Fob

1. Push the black program button 1time

2. Point the control fob at the black program button and press the fob button

3. Enter supervisor code

4. Push the black program button 1time

5. The lock will blink 6times to indicate that the supervisor code was used to add

a control fob

Add a Supervisor Fob Using the Master Code

1. Push the black program button 1time

2. Enter the master code

3. Point the Supervisor Fob at the black program button and press the fob button

4. The lock will blink 6times to indicate that the master code was used to add a

supervisor fob

Add a Supervisor Fob Using the Control Fob

Your control fob is blue and your supervisor fob is black

1. Push the black program button 1time

2. Point your Blue Control Fob at the black program button and press the fob button

3. Point your Black Supervisor Fob at the black program button and press the fob button

4. The lock will blink 6times to indicate that a control fob was used to add a supervisor

fob

Add a User Fob Using the Supervisor Code

Your user fobs are black

1. Push the black program button 2times

2. Enter the supervisor code

3. Point the Black User’s Fob at the black program button and press the fob button

4. The lock will blink 6times to indicate that the supervisor code was used to add a

user fob

Add a User Fob Using the Supervisor Fob

1. Push the black program button 2times

2. Point the Blue Supervisor Fob at the black program button and press the black

program button

3. Point the Black User’s Fob at the black program button and press the fob button

4. The lock will blink 6 times to indicate that the supervisor fob was used to add a user

fob

Remove the User Fob using the Supervisor Code

1. Push the black program button 2times

2. Enter the supervisor code

3. Press 1 1 1 1 1

4. Press the black program button 1time

5. The lock will blink 6times to indicate that the supervisor code was used to remove

the user fob. User fob will no longer be valid for access.

Remove the User Fob using the Supervisor Fob

1. Push the black program button 2times

2. Point the Blue Supervisor Fob at the black program button and press the fob button

3. Enter 1 1 1 1 1

4. Push the black program button 1 time

5. The lock will blink 6times to indicate that the Supervisor Fob was used to remove

the User Fob. The User Fob will no longer be valid for access.

Unlock with a Fob

1. Point either the Blue Supervisor Fob or the Black User’s Fob at the black program

button and press the fob button.

2. Turn the knob to unlock the lock

DoubleDigitCodes

The numbers 6, 7, 8 and 9 can be entered by pressing two keys simultaneously in order

to produce a sum. For example 2 and 4 can be pressed simultaneously to produce the

number 6 (2+4=6). Note, if the code was programmed using 2+4 as the 6 digit, the 2+4

must be used when accessing the lock, because other combinations that equal six such as

1+5 are distinguished from 2+4.

SwitchingModes

Note: The Master Code is retained when switching modes

1. Unlock the MicroCool™ Digital Lock and turn the knob to the unlocked position

2. Remove the battery for 10 seconds

3. While holding the program button, reinsert the battery and was until all 3 LED’s fade

in and fade out simultaneously

4. Release the program button

5. Enter the 6 digit master code. When the master code is entered correctly the yellow

LED will illuminate

6. Press button number 2–two times for LOCKER Mode

7. Once the lock switches modes, the LED’s will flash green, yellow, red

8. Proceed to operate the lock in the selected mode

Andere Handbücher für MicroCool

Inhaltsverzeichnis

Andere Creche Innovations Sperren Handbücher

Creche Innovations

Creche Innovations MicroCool Bedienungsanleitung

Beliebte Sperren Handbücher anderer Marken

Magic

Magic 105 Bedienungsanleitung

Gantner

Gantner GAT NET.Lock 7020 System Kurzanleitung

Wittkopp

Wittkopp Insys 7202 Bedienungsanleitung

Dorma

Dorma Studio Classic Bedienungsanleitung

Securam

Securam ECSL-601 Bedienungsanleitung

Sudhaus

Sudhaus 3003 Bedienungsanleitung

Safety 1st

Safety 1st 48517 Bedienungsanleitung

Pado

Pado FDS-10 Bedienungsanleitung

Esco

Esco systeQ Series Bedienungsanleitung

COMPX

COMPX National D8951 Bedienungsanleitung

secureo

secureo Key Box Bedienungsanleitung

Stock Loks

Stock Loks C8713 Bedienungsanleitung

COMPX

COMPX 1T-058 Betriebsanleitung

Auslock

Auslock T11 Bedienungsanleitung

ELCOM

ELCOM 7205 Bedienungsanleitung

Stealth SAFES

Stealth SAFES ShadowVault Bedienungsanleitung

Knox

Knox KeySecure 5 Bedienungsanleitung

Kwikset

Kwikset 48334/01 Bedienungsanleitung