Crestron CNWM Bedienungsanleitung

CRESTRON

Contents

Wireless Mouse 1

Description 1

Functional Description 1

Physical Description 2

Leading Specifications 3

Setup 4

General Use and Safety 4

RF Identity Code 4

Programming (Cresnet and SmarTouch systems) 9

Programming in SIMPL Windows (Cresnet and SmarTouch systems) 11

Accessing the Inlay Card 18

Problem Solving 20

Troubleshooting 20

Further Inquiries 21

Return and Warranty Policies 22

Merchandise Returns / Repair Service 22

CRESTRON Limited Warranty 22

Appendix A: AT Scan Code 23

Operations Guide - DOC. 5700A Contents •i

CRESTRON

Wireless Mouse

Description

Functional Description

The wireless mouse is a hand-held user interface that uses radio frequency (RF) to

communicate with the CRESNET system, SmarTouch STS or the portable

SmartPresenter system. As part of the CRESNET system, the wireless mouse

communicates with the system via the CNRFGWA, RF receiver. As part of the

SmarTouch STS, the wireless mouse communicates with the system via the ST-CP,

control processor. When used with the SmartPresenter system, the wireless mouse

communicates with the system control processor, SP-1.

NOTE: The CNRFGWA must have PROM # 2251 for wireless mouse support. A

CNRFGWA with this PROM reports on the network with software version 2.00.

Early versions of the CNRFGWA do not support the wireless mouse.

Models

There are two CRESTRON wireless mice available: CNWM and CNWML. The

only difference between the two configurations is that one, the CNWML, is

equipped with a laser pointer. The laser can be turned ON and OFF by depressing

the center button (button 5) or button 4 on the keypad of the unit.

CNWM/L used with Cresnet

By design, the most logical application for the wireless mouse is as the user interface

in a presentation system. The wireless mouse and PC keyboard/mouse controller,

CNMK, can be added to control your PC presentation. These devices in conjunction

with CRESTRON’s simple-to-use Windows software improve the portability of the

user interface. They facilitate the transmission of programmed PC mouse and

keyboard operations as well as serial and IR device commands remotely.

CNWM/L used with SmarTouch™

The CNWM/L can be used in a SmarTouch system. SmarTouch is a radio frequency

(RF) control system that offers unprecedented performance and value. Adding the

CNWML to the SmarTouch system offers keyboard and mouse emulation (with

optional CNMK) and multi-purpose AV control.

Operations Guide - DOC. 5700A Wireless Mouse •1

CRESTRON

CNWM/L used with SmartPresenter™

The wireless mouse serves as the RF transmitter for the SmartPresenter™system.

This is a unique presentation system that is fully operational using the wireless

mouse. With only the compact SP-1 control processor and the wireless mouse, users

can control up to four IR devices and one RS-232 device. SmartPresenter has the

potential to control up to six functions per device. Functions are assigned to the four

positions of the mouse button, the mouse trigger, and the center keypad button on

the wireless mouse. The SmartPresenter system can be programmed easily in the

field using the CNWM/L. Refer to the SmartPresenter Quick Guide (DOC. 5742)

for additional information on field programming.

Physical Description

The wireless mouse, shown below, is housed in a black plastic enclosure that can

easily fit in the user’s palm. Nearly all the buttons, except for the trigger, can be

found on the topside of the unit. The trigger can be found on the bottom of the unit.

Button placement has been carefully designed into the unit for ease of use.

Wireless Mouse Physical Views

1.775"

45.09mm

1.775"

45.09mm

CNWML

6.036"

153.31mm

(lg. btn. 5)

1.775"

45.09mm

CNWM

5.331"

135.41mm

Lazer

Button Device

Buttons

Mouse

Button

1.362"

34.59mm

Trigger

(button 6)

Notice the lined paper beneath the clear plastic cover that surrounds the keypad

buttons. Once functionality has been assigned to the keypad buttons, a brief

description can be written on the lined paper. For a more professional look, a label

kit (SP-LK) is available for the wireless mice. The SP-LK label kit provides a sheet

of the most common control functions and several pre-cut mouse inlay cards.

To access the inlay card, refer to "Accessing the Inlay Card" on page 18.

Two AAA-sized batteries are provided with the wireless mouse. Access to the

battery compartment is permitted after the battery cover is removed. A sensor (photo

transistor) used to program the RF identity code is also located in the battery

compartment.

2 •Wireless Mouse Operations Guide - DOC. 5700A

CRESTRON

Battery Compartment (Rear View)

Leading Specifications

The table below provides a summary of leading specifications for the wireless

mouse. Dimensions and weight are approximations rounded to the nearest

thousandth unit.

Leading Specifications of the Wireless Mouse

SPECIFICATION DETAILS

Battery 2 disposable "AAA" cells

SIMPL™ Windows®Version 1.18 or later

CRESNET Operating System 3.17.29 or later

CNRFGWA Software version 2.00/PROM # 2251

SmarTouch (ST-CP) Operating

System* 4.00.38-s or later

SmarTouch (ST-CP) Monitor Version* 1.29 or later

VisionTools Pro™ Version 1.1.3 or later

Dimensions & Weight Height: 5.331 in (13.541 cm) for CN-WM

(without batteries) 6.036 in (15.33 cm) for CN-WML

Width: 1.775 in (4.509 cm)

Depth: 1.380 in (3.505 cm)

Weight: 0.140 lb (0.064 kg) for CN-WM

0.270 lb (0.122 kg) for CN-WML

* NOTE: Upload the SmarTouch Monitor before uploading the SmarTouch

Operating System.

Laser Specifications of the CNWML

SPECIFICATION DETAILS

Wavelength 670 nm (Class IIIa Product)

Output Power Less than 5 mW

Operations Guide - DOC. 5700A Wireless Mouse •3

CRESTRON

NOTE: This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. The equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which

can determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

As of the date of manufacture, the unit has been tested and found to comply with

specifications for CE marking.

Setup

General Use and Safety

DANGER: The CNWML contains a Class IIIa laser. Avoid direct eye exposure.

Compliance to the following suggestions may extend the life of the wireless mouse

and laser.

• If the unit is not going to be used for a month or longer, remove

batteries. Never leave weak or dead batteries in the unit; they might

leak chemicals that can damage the unit.

• Use care when handling the unit. Dropping the unit can unfocus the

lens, damage circuit boards, and cause the unit to work improperly.

• Operate and store the unit in moderate temperatures. Do not place the

unit in environments below freezing or exceeding 110°F. Temperature

extremes can shorten the life of electrical devices, damage the batteries,

and distort or melt plastic parts.

• Keep the unit away from dust and dirt that can cause premature wear

on parts. Use a damp cloth to wipe the unit. Do not use harsh

chemicals, cleaning solvents, or strong detergents to clean the device.

RF Identity Code

Every hand-held wireless transmitter communicating with either the SmartPresenter,

ST-CP or CNRFGWA requires a unique RF identity (ID) code. The code is a two-

4 •Wireless Mouse Operations Guide - DOC. 5700A

CRESTRON

digit hexadecimal number. To maintain code diversity within a system, use codes

between 10 and FE for the transmitters. There are two methods to change the RF ID

code on the wireless mouse: via the CNIDC (Identity Code Cable) and Viewport

software or depressing buttons on the unit that represent a binary code.

NOTES: The RF ID CODE on the wireless mouse is factory set to 30.

Only use 10 through FE as RF ID code.

Do not confuse RF ID with network (NET) ID.

Match CNWM/L ID to SP-1 Receiver

(SmartPresenter)

Depress and hold the recessed button #1 on the SP-1 for at least 5 seconds (use a

paper clip or similar object) or until the red RF LED flashes on the SP-1.

Depress (position A) button on the CNWM/L while the RF LED flashes.

Observe that RF LED stops flashing and remains illuminated for about 4 seconds.

NOTE: An extinguished LED indicates a match of CNWM/L ID to that of the SP-1.

If the RF ID does not match, refer to "Change RF ID via CNWM/L Button Presses"

on page 7.

Verify RF ID with Crestron Software

(not required for SmartPresenter)

Use the Crestron Performance VeiwPort to view transmitter ID codes. Using either

SIMPL Windows or VisionTools Pro, select ViewPort from the Tools menu; the

“Crestron Performance Viewport” dialog box, shown below, appears.

From the Diagnostics menu in the dialog box, select Identify Transmitter ID to

open the “Transmitter Identification” dialog box. Press a button on the transmitter,

ViewPort will display the transmitter ID in hexadecimal format.

Operations Guide - DOC. 5700A Wireless Mouse •5

CRESTRON

Change RF ID Crestron Software

(not required for SmartPresenter)

Use the Crestron Performance ViewPort to set a RF ID CODE. Using either SIMPL

Windows or VisionTools Pro, select ViewPort from the Tools menu; the “Crestron

Performance Viewport” dialog box, shown below, appears.

Crestron Performance Viewport Dialog Box

From the Options menu in the dialog box, select Set Transmitter ID to open the

“Set Transmitter ID” dialog box. Enter a two-digit hexadecimal number ranging

from 10 to FE. Click OK to confirm.

Set Transmitter ID Dialog Box

6 •Wireless Mouse Operations Guide - DOC. 5700A

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Crestron Maus Handbücher

Crestron

Crestron TPMC-10-MS Bedienungsanleitung

Beliebte Maus Handbücher anderer Marken

Sven

Sven RX-G720 Bedienungsanleitung

3DConnexion

3DConnexion CadMouse Pro Bedienungsanleitung

Canyon

Canyon Puncher GM-20 Bedienungsanleitung

Sharkoon

Sharkoon Light2 180 Bedienungsanleitung

Cherry

Cherry MW 8C ERGO Bedienungsanleitung

NGS

NGS HIT RB Bedienungsanleitung

Sharkoon

Sharkoon FireGlider Bedienungsanleitung

Lenovo

Lenovo Wireless Mouse N3902 Bedienungsanleitung

BASETech

BASETech BN-S11 Bedienungsanleitung

Dell

Dell WM326 Bedienungsanleitung

Areson

Areson B213 Bedienungsanleitung

HP M17587-371 Bedienungsanleitung

Chatpen

Chatpen CHA-30 Bedienungsanleitung

GAMDIAS

GAMDIAS DEMETER GMS5000 Bedienungsanleitung

HP KJ453AA - Wireless Laser Mouse Bedienungsanleitung

Trust

Trust GRAPHIN GXT 960 Bedienungsanleitung

Lenovo

Lenovo SD-9082 Bedienungsanleitung

Alienware

Alienware AW320M Bedienungsanleitung