Crestron DM-TX-4K-202-C Betriebsanleitung

DM-TX-4K-202-C/DM-TX-4K-302-C

4K DigitalMedia 8G+®Transmitters

Supplemental Guide

Crestron Electronics, Inc.

The product warranty can be found at www.crestron.com/warranty.

The specific patents that cover Crestron products are listed at patents.crestron.com.

Certain Crestron products contain open source software. For specific information, please visit www.crestron.com/opensource.

Crestron, the Crestron logo, Crestron Connect It, Crestron Toolbox, DigitalMedia, DigitalMedia 8G+, DM, and DM 8G+ are either trademarks

or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. HDBaseT and the HDBaseT Alliance logo

are either trademarks or registered trademarks of the HDBaseT Alliance in the United States and/or other countries. HDMI and the HDMI logo

are either trademarks or registered trademarks of HDMI Licensing LLC in the United States and/or other countries. Other trademarks,

registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their

products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or

photography.

This document was written by the Technical Publications department at Crestron.

Supplemental Guide – DOC. 7932A Contents •i

Contents

Introduction 1

Physical Description 2

Side View, Left ........................................................................................................ 2

Side View, Right...................................................................................................... 4

Configuration 5

EDID Configuration.................................................................................................. 5

HDBaseT Configuration........................................................................................... 7

USB HID Control Configuration ............................................................................... 8

HDCP 2.2 Compliance 8

Troubleshooting 9

Appendix: Pin Assignments 11

Supplemental Guide – DOC. 7932A DM-TX-4K-202-C/DM-TX-4K-302-C: 4K DigitalMedia 8G+ Transmitters •1

DM-TX-4K-202-C/DM-TX-4K-302-C:

4K DigitalMedia 8G+®Transmitters

Introduction

The Crestron®DM-TX-4K-202-C and DM-TX-4K-302-C are DigitalMedia 8G+®transmitters

and switchers that provide support for the transport of 4K and Ultra HD video signals.

The DM-TX-4K-202-C and DM-TX-4K-302-C provide two HDMI®inputs. In addition to the

HDMI inputs, the DM-TX-4K-302-C provides one VGA input and one analog audio input.

The DM-TX-4K-202-C and DM-TX-4K-302-C also function as control modules, providing

RS-232 and IR control ports. An Ethernet port and a USB HID port are also provided.

This guide provides information about the following:

•Physical description of the side views of the DM-TX-4K-202-C and

DM-TX-4K-302-C

•Configuration of some of the capabilities of the DM-TX-4K-202-C and

DM-TX-4K-302-C, for example, automatic audio/video signal format management

via EDID

•HDCP 2.2. compliance

•Troubleshooting

•Pin assignments

For additional information, refer to the DM-TX-4K-202-C/DM-TX-4K-302-C DO Guide

(Doc. 7743) at www.crestron.com/manuals.

2•DM-TX-4K-202-C/DM-TX-4K-302-C: 4K DigitalMedia 8G+ Transmitters Supplemental Guide – DOC. 7932A

Physical Description

This section provides information about the connectors, controls, and indicators on the left

and right sides of the DM-TX-4K-202-C and DM-TX-4K-302-C.

Side View, Left

The following illustration shows the left side of the DM-TX-4K-302-C.

NOTE: The left side of the DM-TX-4K-202-C provides the same connectors and indicators

as the DM-TX-4K-302-C with the exception of the VGA IN connector and indicator and the

AUDIO IN connector.

Side View, Left (DM-TX-4K-302-C Shown)

VGA IN LED: (DM-TX-4K-302-C only) Green LED, indicates video signal presence at

the VGA input

VGA IN: (DM-TX-4K-302-C only) HD15 female, analog VGA/RGB/video input;

Signal Types: VGA, RGB, component, S-Video, or composite;

Formats: RGBHV, RGBS, RGsB, YPbPr, Y/C, NTSC, PAL;

Input Levels: 0.5 to 1.5 Vp-p with built-in DC restoration;

Input Impedance: 75 Ohms;

Sync Input Type: Autodetect RGBHV, RGBS, RGsB, YPbPr, Y/C, composite;

Sync Input Level: 3 to 5 Vp-p;

Sync Input Impedance: 510 Ohms

NOTE: The VGA IN port requires an appropriate passive adapter or breakout cable to

accommodate a component, S-video, or composite video signal.

AUDIO IN: (DM-TX-4K-302-C only) 3.5 mm TRS mini phone jack;

Unbalanced stereo line-level audio input;

Input Level: 2 Vrms maximum;

Input Impedance: 10k Ohm





















Supplemental Guide – DOC. 7932A DM-TX-4K-202-C/DM-TX-4K-302-C: 4K DigitalMedia 8G+ Transmitters •3

HDMI IN 1–2 LEDs:Green LEDs, each indicates HDMI signal presence at the

corresponding HDMI input

HDMI IN 1–2: 19-pin Type A HDMI female;

HDMI digital video/audio inputs;

(DVI and Dual-Mode DisplayPort compatible)

NOTE: The HDMI IN ports require an appropriate adapter or interface cable to

accommodate a DVI or Dual-Mode DisplayPort signal. The CBL-HD-DVI interface cable

is available separately.

DM OUT: 8-pin RJ45 female, shielded;

DM 8G+®output, HDBaseT®standard compliant;

PoDM+ PD (Powered Device) port (IEEE 802.3at Type 2 Class 4 [25.5 W] compliant

and HDBaseT PoE+ compatible) on DM-TX-4K-302-C;

PoDM PD port (IEEE 802.3at Type 1 Class 3 [12.95 W] compliant and HDBaseT PoE

compatible) on DM-TX-4K-202-C;

Connects to the DM 8G+ input of a DM®switcher, receiver, or other DM device, or to

an HDBaseT device via CAT5e, Crestron DM-CBL-8G, or Crestron DM-CBL-ULTRA

cable;

Green LED indicates DM link status;

Solid amber LED indicates HDCP video;

Blinking amber LED indicates non-HDCP video

NOTE: Receiving PoDM+ or PoDM requires connection to a switcher or other

equipment that has a corresponding PoDM+ or PoDM PSE (Power Sourcing

Equipment) port. Receiving HDBaseT PoE+ or HDBaseT PoE requires connection to a

switcher or other equipment that has a corresponding HDBaseT PoE+ or HDBaseT

PoE PSE port. Any wiring that is connected to a PoDM+, PoDM, HDBaseT PoE+, or

HDBaseT PoE PSE port is for intrabuilding use only and should not be connected to a

line that runs outside of the building in which the PSE is located.

NOTE: If the DM-TX-4K-302-C does not connect to the included power pack, the

DM-TX-4K-302-C requires PoDM+ or HDBaseT PoE+ to power a USB device

connected to the USB HID port. Standard PoDM or HDBaseT PoE can be used to

power the DM-TX-4K-302-C if no USB device connects to the USB HID port. Unlike for

the DM-TX-4K-302-C, standard PoDM or HDBaseT PoE can be used to power a USB

device connected to the USB HID port of the DM-TX-4K-202-C.

Power LED: Green LED, indicates operating power supplied via PoDM+, PoDM,

HDBaseT PoE+, or HDBaseT PoE for the DM-TX-4K-302-C; PoDM or HDBaseT PoE

for the DM-TX-4K-202-C; or local power pack

24 VDC 0.75A: 2.1 x 5.5 mm dc power connector;

24 Vdc power input;

Power pack included

Ground ()::6-32 screw, chassis ground lug

For pin assignment information, refer to the Appendix on page 11.

4•DM-TX-4K-202-C/DM-TX-4K-302-C: 4K DigitalMedia 8G+ Transmitters Supplemental Guide – DOC. 7932A

Side View, Right

The following illustration shows the right side of the DM-TX-4K-302-C.

NOTE: The right side of the DM-TX-4K-202-C provides the same connectors, controls, and

indicators as the right side of the DM-TX-4K-302-C.

Side View, Right (DM-TX-4K-302-C Shown)

USB HID: USB Type A female;

USB 2.0 host port for connection of a mouse, keyboard, or other USB HID compliant

device (USB signal extension and routing), or for connection of a Crestron TT-100 series

device (Crestron Connect It™ Cable Caddy. sold separately)

COMPUTER: USB Type B female;

USB 2.0 device port for computer console (setup) or for connection to a computer or

other USB HID compliant host (USB signal extension and routing)

LAN: 8-pin RJ-45 female;

10BASE-T/100BASE-TX Ethernet port;

Green LED indicates Ethernet link status;

Amber LED indicates Ethernet activity

NOTE: Do not connect the LAN port to an Ethernet switch if the DM OUT port

connects to a DigitalMedia™ switcher.

HDMI OUT: 19-pin Type A HDMI female;

HDMI digital video/audio output (DVI compatible)

NOTE: The HDMI OUT port requires an appropriate adapter or interface cable to

accommodate a DVI signal. The CBL-HD-DVI interface cable is available separately.

HDMI OUT LED: Green LED, indicates HDMI signal presence at the HDMI output

COM:5-pin 3.5 mm detachable terminal block;

Bidirectional RS-232 port;

Up to 115.2k baud, hardware and software handshaking support



















Supplemental Guide – DOC. 7932A DM-TX-4K-202-C/DM-TX-4K-302-C: 4K DigitalMedia 8G+ Transmitters •5

IR: 2-pin 3.5 mm detachable terminal block;

IR/serial port;

IR output up to 1.1 MHz;

1-way serial TTL/RS-232 (0-5 volts) up to 19200 baud

SETUP: (Applicable only to a configuration in which a DigitalMedia switcher is not

used) Red LED and recessed push button for Ethernet setup of the default static IP

address of the device

NOTE: The default static IP address of the DM-TX-4K-302-C and the

DM-TX-4K-202-C is 192.168.1.205.

RESET: Recessed push button for reboot of the device

For pin assignment information, refer to the Appendix on page 11.

Configuration

This section provides information about the following:

•EDID configuration

•HDBaseT configuration

•USB HID control configuration

EDID Configuration

EDID (Extended Display Identification Data) configuration allows management of the EDID

that is to be sent to the upstream device connected to an HDMI input of the

DM-TX-4K-202-C or to an HDMI or VGA input of the DM-TX-4K-302-C. By default, the

EDID is set to DM default 4k 60Hz 2 ch for an HDMI input or to 01 DM default for a VGA

input.If a different EDID is desired, use DMTool to configure the EDID. An overview of the

steps necessary to configure the EDID is as follows:

NOTE: For detailed information, refer to the Crestron Toolbox™ help file.

1. Connect to the DM-TX-4K-202-C or DM-TX-4K-302-C.

2. Open the Setup window of the HDMI input for the DM-TX-4K-202-C or the Setup

window of the HDMI or VGA input for the DM-TX-4K-302-C.

3. In the EDID Configuration dialog box, configure the EDID by doing any of the

following:

oCustomize the current EDID.

oLoad an EDID template and modify it.

oCreate a new EDID file.

oLoad the existing EDID and modify it.

oObtain an EDID from the output and then save or customize it.

oApply an EDID that is saved on a computer.

6•DM-TX-4K-202-C/DM-TX-4K-302-C: 4K DigitalMedia 8G+ Transmitters Supplemental Guide – DOC. 7932A

EDID Configuration Dialog Box for HDMI Input (DM-TX-4K-302-C Dialog Box Shown)

EDID Configuration Dialog Box for VGA Input (DM-TX-4K-302-C Only)

Andere Handbücher für DM-TX-4K-202-C

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Crestron Sender Handbücher

Crestron

Crestron DM-TX-4KZ-100-C-1G Bedienungsanleitung

Crestron

Crestron DM-TX-4KZ-202-C Bedienungsanleitung

Crestron

Crestron HD-TX-4KZ-111-1G Bedienungsanleitung

Crestron

Crestron DigitalMedia DM-TX-100F Bedienungsanleitung

Crestron

Crestron ST-4T Bedienungsanleitung

Crestron

Crestron HD-TXC-4KZ-101-1G Bedienungsanleitung

Crestron

Crestron HD-TX-4KZ-401 Bedienungsanleitung

Crestron

Crestron DigitalMedia 8G+ DM-TX-201-C Betriebsanleitung

Crestron

Crestron CNIRHT-MM Bedienungsanleitung

Crestron

Crestron DigitalMedia 8G+ DM-TX-4KZ-100-C-1G Bedienungsanleitung

Crestron

Crestron DigitalMedia DM-TX-300N Bedienungsanleitung

Crestron

Crestron Digitalmedia 8G+ Transmitter 401 Bedienungsanleitung

Crestron

Crestron DigitalMedia DM-TX-100F Bedienungsanleitung

Crestron

Crestron IM-WCC Anleitung zur Verwendung

Crestron

Crestron CNIRHT-15 Bedienungsanleitung

Crestron

Crestron CNRFHT-15A Bedienungsanleitung

Crestron

Crestron DigitalMedia DMF-TX-4K-SFP Maßzeichnung

Crestron

Crestron IM-WCVI Bedienungsanleitung

Crestron

Crestron DM-TX-4KZ-202-C Maßzeichnung

Crestron

Crestron DM-TX-201-S Maßzeichnung

Crestron

Crestron HD-TXC-4KZ-101 Bedienungsanleitung

Crestron

Crestron DM-TX-4K-202-C Bedienungsanleitung

Crestron

Crestron DM-TX-200 Anleitung zur Verwendung

Crestron

Crestron DigitalMedia 8G+ DM-TX-4KZ-202-C Betriebsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung