Cross Technologies 2016-75-213 Bedienungsanleitung

Artisan Technology Group is your source for quality

new and certied-used/pre-owned equipment

• FAST SHIPPING AND

DELIVERY

• TENS OF THOUSANDS OF

IN-STOCK ITEMS

• EQUIPMENT DEMOS

• HUNDREDS OF

MANUFACTURERS

SUPPORTED

• LEASING/MONTHLY

RENTALS

• ITAR CERTIFIED

SECURE ASSET SOLUTIONS

SERVICE CENTER REPAIRS

Experienced engineers and technicians on staff

at our full-service, in-house repair center

WE BUY USED EQUIPMENT

Sell your excess, underutilized, and idle used equipment

We also offer credit for buy-backs and trade-ins

www.artisantg.com/WeBuyEquipment

REMOTE INSPECTION

Remotely inspect equipment before purchasing with

our interactive website at www.instraview.com

LOOKING FOR MORE INFORMATION?

Visit us on the web at www.artisantg.com for more

information on price quotations, drivers, technical

specications, manuals, and documentation

View

Instra

Instruction Manual Model 2016-75-213

Downconverter

April 2009 Rev A

EXECUTE

MODEL 2016

CROSS TECHNOLOGIES INC.

719 to 201 MHZ

G=+10 REF=INT

MUTE

REMOTE

POWER

ALARM

DOWNCONVERTER

Data, drawings, and other material contained herein are proprietary to Cross Technologies, Inc.,

but may be reproduced or duplicated without the prior permission of Cross Technologies, Inc.

for purposes of operating the equipment.

When ordering parts from Cross Technologies, Inc., be sure to include the equipment

model number, equipment serial number, and a description of the part.

CROSS TECHNOLOGIES, INC.

6170 Shiloh Road

Alpharetta, Georgia 30005

(770) 886-8005

FAX (770) 886-7964

Toll Free 888-900-5588

WEB www.crosstechnologies.com

E-MAIL [email protected]

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

INSTRUCTION MANUAL

MODEL 2016-75-213 Downconverter

TABLE OF CONTENTS PAGE

Warranty 2

1.0 General 3

1.1 Equipment Description 3

1.2 Technical Characteristics 4

1.3 Monitor & Control Interface 5

1.4 Environmental Use Information 7

2.0 Installation 8

2.1 Mechanical 8

2.2 Rear I/O’s 9

2.3 Front Panel Controls, Indicators 10

2.4 Operation 11

2.5 Menu Settings 12

WARRANTY - The following warranty applies to all Cross Technologies, Inc. products.

All Cross Technologies, Inc. products are warranted against defective materials and

workmanship for a period of one year after shipment to customer. Cross Technologies,

Inc.’s obligation under this warranty is limited to repairing or, at Cross Technologies, Inc.’s

option, replacing parts, subassemblies, or entire assemblies. Cross Technologies, Inc. shall

not be liable for any special, indirect, or consequential damages. This warranty does not

cover parts or equipment which have been subject to misuse, negligence, or accident by the

customer during use. All shipping costs for warranty repairs will be prepaid by the

customer. There are not other warranties, express or implied, except as stated herein.

CROSS TECHNOLOGIES, INC.

6170 Shiloh Road

Alpharetta, Georgia 30005

(770) 886-8005

FAX (770) 886-7964

Toll Free 888-900-5588

WEB www.crosstechnologies.com

E-MAIL [email protected]

2016-75-213, Rev. A Manual Page 2 4/16/09

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

MODEL 2016-75-213 Downconverter

1.0 General

1.1 Equipment Description

The 2016-75-213 Downconverter converts 719 MHz to 201.143 or 213.143 ± 3 MHz with low group delay and

flat frequency response. Synthesized local oscillators (LO) provide output frequency selection. Multi-function

push button switches select the output frequency, gain, and other parameters. Front panel LEDs provide

indication of DC power (green), remote operation (yellow), and PLL alarm (red). Variable attenuators for the

RF input provide a gain range of 0 to +40 dB as adjusted by the front panel multi-function pushbutton switches.

Remote operation allows selection of output frequency and gain. Parameter selection and frequency translation

and gain settings appear on the LCD display. Connectors are Type F female for the RF and BNC female for IF

and optional 10 MHz input and output signals (option -E). A high stability (±0.01ppm) (option -H) is also

available. The unit is powered by a 100-240 ± 10% VAC power supply, and housed in a 1 3/4” X 19“ X 16”

rack mount chassis.

EXECUTE

MODEL 2016

CROSS TECHNOLOGIES INC.

719 to 201 MHZ

G=+10 REF=INT

MUTE

REMOTE

POWER

ALARM

DOWNCONVERTER

FRONT PANEL

RF OUT

GND

J18

10 MHZ REF

10 MHZ

IF IN

EXT REF

OUTPUT

INPUT

DS7

VDC on RF

J10

AND

MONITOR

CONTROL

REAR PANEL

FIGURE 1.1 Model 2016-75-213 Front and Rear Panels

719

MHz

350 to 750 MHz

CONTROLLER

201 to 719 MHZ

G=+10 REF=INT

LO1

LO2

VAR

ATT

10MHz*

+24VDC*

EXT

10 M*

INT/EXT

10 M

VAR

ATT

1751

201.143

213.143

MHz

OUT

Block Diagram

FIGURE 1.2 Model 2016-75-213 Downconverter Block Diagram

2016-75-213, Rev. A Manual Page 3 4/16/09

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

1.2 Technical Characteristics

TABLE 1.0 2016-75-213 Downconverter Specifications*

Input Characteristics

Impedance/Return Loss 75 Ω/12 dB (see TABLE 2.2 for connector options)

Frequency 719 MHz ± 3 MHZ

Input Level -60 to -20 dBm

Output Characteristics

Impedance/Return Loss 75 Ω/12 dB (see Table 2.2 for connector options)

Frequency 201.143 or 213.143 ± 3 MHz

Level Range -30 to -20 dBm

Output 1 dB Compression -15 dBm

Channel Characteristics

Gain range (adjustable) 0.0 to +40 dB

Image Rejection <50 db, min.

Frquency Reponse 201.143 or 213.143 ± 3 MHz out; ± 0.5 dB

Spurious Response <-45 dBC, in band

Group Delay, max. 0.01 ns/MHz2parabolic; 0.03 ns/MHz linear; 1 ns ripple

Frequency Sense Non-inverting

Synthesizer Characteristics

Frequency Accuracy ± 1.0 ppm max over temp (± 0.01 ppm option -H) internal reference

Frequency Step 1.0 MHz minimum

10 MHz In/Out Level 3 dBm, ± 3 dB, 75 (option -E)

-110

-95

-80

-70

1MHz

100kHz

10kHz

1kHz

10Hz

dBC/Hz

Phase Noise @ Freq

Controls, Indicators

Frequency/Gain Selection direct readout LCD; manual or remote

Power Green LED

Alarm Red LED

Remote Yellow LED; RS232C (RS485, option -Q), 9600 baud

Other

RF, IF Connector Type F (female) (see TABLE 2.2 for other options)

IF Connector BNC (female) (see TABLE 2.2 for other options)

Ext 10 MHz Conn. (In/Out) BNC (female) (option -E)

Alarm/Remote Connector DB9 - NO or NC contact closure on Alarm

Size 19 inch, 1RU standard chassis 1.75”high X 16.0” deep

Power 100-240 ±10% VAC, 47-63 Hz, 45 watts max

Options Available

E - External 10 MHz ref input & output Connectors/Impedance

H - High Stability Internal Ref (±0.01 ppm) B - 75ΩBNC (RF), 75ΩBNC (IF)

Q - RS485 Remote Interface C - 50ΩBNC (RF), 75ΩBNC (IF)

X - 125 kHz Frequency Steps D - 50ΩBNC (RF), 50ΩBNC (IF)

N - 50ΩN-type (RF), 75ΩBNC (IF)

M - 50ΩN-type (RF), 50ΩBNC (IF)

S - 50ΩSMA (RF), 50ΩBNC (IF)

*+10˚C to +40˚C; Specifications subject to change without notice.

2016-75-213, Rev. A Manual Page 4 4/16/09

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

1.3 Monitor and Control Interface

A) Remote serial interface

Protocol: RS-232C, 9600 baud rate, no parity, 8 data bits, 1 start bit, and 1 stop bit.

(RS-232C, RS-422, or RS-485 - option -Q)

Female DB-9

PC Com Port

Male DB-9

2015/16/17 M&CPort

M&C Cable Diagram - Cross Technologies Frequency Converters

Connector: Rear panel, DB-9 male

J10 Pinouts (RS-232C/422/485)

Pin Function

1 Rx-

2 Rx+ (RS-232C)

3 Tx+ (RS-232C)

4 Tx-

5 GND

6 Alarm Relay: Common

7 Alarm Relay: Normally Open

8 Not Used

9 Alarm Relay: Normally Closed

2016-75-213, Rev. A Manual Page 5 4/16/09

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

B) Status Requests Table 1.1 lists the status requests for the 2016-75-40 and briefly describes them

*PLEASE NOTE: The two character {aa}(00-31) prefix, in the table below,

should be used ONLY when RS-485, (OPTION-Q), is selected.

TABLE 1.1 2016-75-213

STATUS REPORT

Command Syntax * Description

Command Status {aaS1} Returns {aaS1bccAM} where:

• b = 0 if input frequency = 201 MHz

• b = 1 if input frequency = 213 MHz

• cc = Tx gain

• A = 0 - summary alarm

Reference Status {aaS2} Returns {aaS2E} where:

• E = Ext 10MHz Status (1 = on, 0 = off)

C) Commands Table 1.2 lists the commands for the 2016-75-213 and briefly describes them. After a

command is sent the 2016-75-213 sends a return “>” indicating the command has been received and executed.

General Command Format - The general command format is {aaCND...}, where:

{ = start byte

aa = address (RS-485 only - option -Q)

C = 1 character, either C (command) or S (status)

N = 1 character command or status request

D = 1 character or more of data (depends on command)

} = stop byte

*PLEASE NOTE: The two character {aa}(00-31) prefix, in the table below,

should be used ONLY when RS-485, (OPTION-Q), is selected.

Talbe 1.2 2016-75-213 COMMANDS

Command Syntax* Description

Set Input Frequency {aaC1x} where:

• x = 1 characters

• x = 0 for 201 MHz

• x = 1 for 213 MHz

Set Transmit Gain {aaC3xx} • Range: 0 to 40 dB

Set External Reference {aaCEx} where x =

• 0 to disable External 10MHz ref signal

Enable Remote # • 1 to enable External 10MHz ref signal

Disable Remote {aaCR0} Just # sign

{CR and zero}

2016-75-213, Rev. A Manual Page 6 4/16/09

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

1.4 Environmental Use Information

A.Rack-Mounting - To mount this equipment in a rack, please refer to the installation instructions

located in the user manual furnished by the manufacturer of your eqipment rack.

B. Mechanical loading - Mounting of equipment in a rack should be such that a hazardous condition

does not exist due to uneven weight distribution.

C.Elevated operating ambient temperature - If installed in a closed or multi-unit rack assembly,

the operating ambient temperature of the rack may be greater than room ambient temperature.

Therefore, consideration should be given to Tmra.

D. Reduced air flow - Installation of the equipment in a rack should be such that the amount of air flow

required for safe operation of the equipment is not compromised. Additional space between unit

may be required.

E. Circuit Overloading - Consideration should be given to the connection of the equipment to the supply

circuit and the effect that overloading of circuits could have on over current protection and supply wiring.

Appropriate consideration of equipment name plate rating should be used, when addressing this concern.

F. Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular

attention should be given to supply connections other than direct connection to the Branch

(use of power strips).

G. Top Cover - There are no servicable parts inside the product so, the Top Cover should not be removed.

If the Top Cover is removed the ground strap and associated screw MUST BE RE-INSTALLED

prior to Top Cover screw replacement. FAILURE TO DO this may cause INGRESS and/or EGRESS

emission problems.

2016-75-213, Rev. A Manual Page 7 4/16/09

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

2.0 Installation

2.1 Mechanical - The 2016-75-213 consists of one RF/Controller PCB housed in a 1 RU (1 3/4 inch high) by

16 inch deep chassis. A switching, ± 12, +24, +5 VDC power supply provides power for the assemblies.

The 2016-75-213 can be secured to a rack using the 4 holes on the front panel.

Figure 2.0 shows how the 2016-75-213 is assembled.

POWER

SUPPLY

FIGURE 2.0 2016-75-213 Mechanical Assembly

2016-75-213, Rev. A Manual Page 8 4/16/09

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

2.2 Rear Panel Input/Output Signals - Figure 2.1 shows the input and output connectors on the rear panel.

AC1 - POWER IN

AC input for switching

power supply.

100-240 ±10% VAC,

47-60 Hz.

J10 - MONITOR AND CONTROL

DB9 female connector. see Table 2.1.

J3 - 10 MHz EXT REF INPUT (Option -E)

10 MHz external reference input, 3 ± 3 dBm, 75

ohms, BNC female connector.

GND

J18

10 MHZ REF

OUTPUT

J10

AND

MONITOR

CONTROL

RF OUT

10 MHZ

IF IN

EXT REF

J5 - RF OUT

250-750 MHz,

0 to -20 dBm output

see Table 2.2.

J4 - IF IN

70 MHz,

-10 to -40 dBm input

see Table 2.2.

DS7

VDC on RF

INPUT

DS7 - SSPB ALARM LED (option -V)

Lights yellow when +24 VDC SSPB

voltage is present on RF OUT, J5,

center pin.

J18 - 10 MHz REF OUTPUT (option -E)

10 MHz reference output. 75ΩBNC

female connector.

FIGURE 2.1 2016-75-213 Rear Panel I/Oʼs

TABLE 2.1 J10 Pinouts (RS-232C/422/485*)

Pin Function

1 Rx-

2 Rx+ (RS-232C)

3 Tx+ (RS-232C)

4 Tx-

5 GND

6 Alarm Relay: Common

7 Alarm Relay: Normally Open

8 Not Used

9 Alarm Relay: Normally Closed

*Remote Serial Interface

Interface: DB-9 Male

Protocol: RS-232C (RS-232C/422/485 option -Q), 9600 baud rate, no parity,

8 data bits, 1 start bit, 1 stop bit.

TABLE 2.2 IF/RF Connector Options

Option IF RF

STD BNC, 75ΩType F, 75Ω

-B BNC, 75ΩBNC, 75Ω

-C BNC, 75ΩBNC, 50Ω

-D BNC, 50ΩBNC, 50Ω

-N BNC, 75ΩType N, 50Ω

-M BNC, 50ΩType N, 50Ω

-S BNC, 50ΩSMA, 50Ω

2016-75-213, Rev. A Manual Page 9 4/16/09

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Inhaltsverzeichnis

Andere Cross Technologies Medienkonverter Handbücher

Cross Technologies

Cross Technologies 3117-3338 720 Series Bedienungsanleitung

Cross Technologies

Cross Technologies 2016-8085 Bedienungsanleitung

Cross Technologies

Cross Technologies 2017-1727-140 Bedienungsanleitung

Cross Technologies

Cross Technologies 2117-7172 Bedienungsanleitung

Cross Technologies

Cross Technologies 2099-10 Bedienungsanleitung

Cross Technologies

Cross Technologies 2016-12 Bedienungsanleitung

Cross Technologies

Cross Technologies 2016-57 Bedienungsanleitung

Cross Technologies

Cross Technologies 2416 25 Series Bedienungsanleitung

Cross Technologies

Cross Technologies 2416 02I Series Bedienungsanleitung

Cross Technologies

Cross Technologies 2017-93 Bedienungsanleitung

Cross Technologies

Cross Technologies 4117-14 Bedienungsanleitung

Cross Technologies

Cross Technologies 2009-2425-1750 Bedienungsanleitung

Cross Technologies

Cross Technologies 2005-10 Bedienungsanleitung

Cross Technologies

Cross Technologies 2016-03A Bedienungsanleitung

Cross Technologies

Cross Technologies 2117 Bedienungsanleitung

Cross Technologies

Cross Technologies 2005 Bedienungsanleitung

Cross Technologies

Cross Technologies 4115-41-212 Bedienungsanleitung

Cross Technologies

Cross Technologies 4116-31-184 Bedienungsanleitung

Cross Technologies

Cross Technologies 2116-116 Bedienungsanleitung

Cross Technologies

Cross Technologies 2116-140T120 Bedienungsanleitung

Cross Technologies

Cross Technologies 4116-31-2831 Bedienungsanleitung

Cross Technologies

Cross Technologies 3116-145-1600 Bedienungsanleitung

Cross Technologies

Cross Technologies 2016-95 Bedienungsanleitung

Cross Technologies

Cross Technologies 2017-03 Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung