Crown Royal Stoves PRISTINE Series Bedienungsanleitung

TABLE OF CONTENTS

INTRODUCTION ....................................................................................................................................... 5

BEST BURN PRACTICES............................................................................................................................. 6

ADDITIONAL INSTALLATION AND OPERATIONAL CONSIDERATIONS ........................................................ 7

GUIDE TO BURNING WOOD ..................................................................................................................... 8

SAFETY INSTRUCTIONS & PRECAUTIONS.................................................................................................. 9

PRECAUTIONARY LABELING ................................................................................................................... 10

INSTALLATION ....................................................................................................................................... 11

FURNACE FLOOR PLAN........................................................................................................................... 13

CHIMNEY ............................................................................................................................................... 14

TRANSFER LINE - INSTALLATION ............................................................................................................ 15

INSTALLATION ....................................................................................................................................... 16

EXISTING HOT WATER HEAT INSTALLATION........................................................................................... 17

DOMESTIC HOT WATER & FORCED AIR INSTALLATION .......................................................................... 18

BRAZED PLATE SETUP - INSTALLATION................................................................................................... 19

WATER TO AIR SET UP - INSTALLATION.................................................................................................. 20

STOVE COMPONENTS ............................................................................................................................ 21

CONTROL PANEL .................................................................................................................................... 23

START UP & OPERATION........................................................................................................................ 24

OPERATION............................................................................................................................................ 25

WEEKLY MAINTENANCE......................................................................................................................... 27

GENERAL MAINTENANCE....................................................................................................................... 28

TROUBLESHOOTING............................................................................................................................... 30

ELECTRICAL WIRE DIAGRAM .................................................................................................................. 31

HPBA SMOKE TROUBLESHOOTING CHECKLIST ....................................................................................... 33

AUTHORIZED FURNACE TREATMENT ..................................................................................................... 38

FURNACE TREATMENT PROCEDURE....................................................................................................... 39

MANDATORY WATER TREATMENT & TESTING ...................................................................................... 40

EMERGENCY PROCEDURE FOR CHEMICAL.............................................................................................. 41

20 YEAR LIMITED WARRANTY ................................................................................................................ 42

WARRENTY CLAIM FORM ...................................................................................................................... 43

ELECTRONIC TEMPERATURE CONTROL MANUAL (16E09-101) ............................................................... 46

Greentech Manufacturing would like to thank you for your recent purchase of a Crown Royal Stove. We sincerely appreciate the

trust you have placed in us and we look forward to continuing to serve you. We know that you will be pleased with our continued

commitment to your satisfaction while you enjoy the benefits of heating with a Crown Royal Stove. Crown Royal Stoves are

manufactured with quality workmanship and designed to offer you value now and for years to come. We are so confident in the

quality of our furnace each Crown Royal Stove comes with a 20 year limited warranty.

To ensure maximum benefits from your furnace, read the complete manual prior to using or installing your furnace.

Always keep this manual for future references.

Crown Royal Stoves –EPA 2020 Step 2 Certified

U.S. ENVIRONMENTAL PROTECTION AGENCY Certified to comply with the 2020 particulate emission standards using cord wood.

7200E: Tested to ASTM E2618-13, average emission rate .08 lbs/mmbtu, maximum emission rate 0.120 lbs/mmbtu.

7300E: Tested to ASTM E2618-13, average emission rate .08 lbs/mmbtu, maximum emission rate 0.118 lbs/mmbtu.

7400E: Tested to ASTM E2618-13, average emission rate .06 lbs/mmbtu, maximum emission rate 0.069 lbs/mmbtu.

The outdoor series furnaces are designed to be located next to your firewood storage for convenience and is normally filled once or

twice a day, depending on the temperature outside. Our outdoor series furnaces are often used to heat residential home, garages,

shops, barns, businesses, greenhouses, swimming pools, spas, domestic hot water, radiant in-floor heat, and snow melt applications.

Model

7200E

7300E

7400E

Estimated Btu’s*

125,000

221,000

325,000

Heating Capacity**

2,000-3,000 sq ft

4,000 –5,000 sq ft

8,000-10,000 sq ft

Dimensions (L X W X H)

70” x 47” x 71-1/2”

plus chimney length

76” x 49” x 80-1/2”

plus chimney length

84” x 53” x 86-1/2”

plus chimney length

Approx Weight

1950 lbs

2650 lbs

2950 lbs

Firebox Length

28”

32”

36”

Wood Load Capacity

26”

30”

34”

Chimney Size

6”

8”

Firebox Door Size (L X H)

18” x 18”

20” x 24”

22” x 26”

Supply/Return Size

1-1/4” (1 Each)

1-1/4” (2 Each)

Water Capacity

180 Gallons

235 Gallons

290 Gallons

Electrical Rating

115 VAC/60HZ/1 PH

*Btu’s are estimated and will vary with the type of wood burned.

**Ensure to properly size unit to buildings thermal demands.

Crown Royal High Efficiency Wood Gasification Furnaces are designed to burn only clean, dry wood. Clean wood means wood that

has no paint, stains, or other type of coatings. It also includes wood that has not been treated with preservatives, including but not

limited to, copper chromium arsenate, creosote or pentachlorophenol. Wood must be cured between 6-9 months and dried to 20%

moisture or less.

Warranty will be voided if the furnace is used to burn materials for which the unit is not certified by the EPA and void if not

operated according to the owner’s manual. Burning any other material other than “Clean, Dry Wood” will VOID warranty.

For Outdoor Use Only!

This wood heater needs periodic inspection and repair for proper operation. It is against federal regulations to operate this wood

heater in a manner inconsistent with operating instructing in this manual.

INTRODUCTION

Learn how to get the best burn possible from your Crown Royal Stove.

Instructions –Read and follow all operating instructions supplied by Greentech Manufacturing, Inc.

Fuels –Only burn clean wood, which is the only approved fuel in your Crown Royal Stove. Burning materials not recommended play

a major role in visible emissions. Never burn: trash, plastics, gasoline, rubber, naphtha, household garbage, material treated with

petroleum products, particle board, railroad ties, pressure treated wood, leaves, paper products and cardboard.

Loading of Fuels –Burning wood creates visible emissions. In order to complete the combustion process, there is a minimum

amount of space needed. For instance, if a person were to load a relatively small firebox completely and load a larger firebox with

the same amount of fuel, with all of the other factors being the same, the larger firebox would burn cleaner. In the smaller firebox,

the combustion process does not have enough room to expand heat up and mix before exiting the firebox (insufficient time,

temperature and turbulence). Just because a firebox is large does not mean that is should be filled completely. This large volume is

used in part for what happens after it is loaded. Fireboxes should be loaded based on outdoor temperatures, and anticipated heat

load required to maintain sufficient levels to ensure the fire doesn’t go out before next fill.

Starting –Always start fire with wood kindling to eliminate unnecessary smoke. Never use gasoline, lighter fluids, chemicals, or oils.

Furnace Sizing –The size of a furnace should be large enough to provide sufficient heat without constant reloading. Targeted burn

times are around 12 hours; an adequately sized furnace will provide enough heat for 90% of all heating days. Inadequate size of

furnace will lead to unattended fires that leave colder fireboxes and relighting will be dirtier because the flame quenching on the

cool firebox walls. A good rule to follow is that if the furnace cannot stay within 20% of its set temperature under regular reloading,

then the unit is undersized and larger furnace is needed.

Operation –Improper combustion air can be associated with several factors. The air inlet and chimney may be restricted by debris

(creosote, ash, etc). The blower starts and stops properly and runs at proper speed. The door seal is in satisfactory condition.

Maintenance –Excessive creosote buildup can be a result of restricted air flow from combustion fan, flame baffle or chimney

blockage.

Local and State Regulations –Always remember to comply with all applicable state and local codes.

BEST BURN PRACTICES

DANGER!!! Do not start fire with chemicals, volatile fluids, rubber, plastics or garbage. Some processed wood contain resins and

should be avoided. Only competent persons with a sound understanding of this heating method should operate this furnace.

Improper firing could result in personal injury and/or damage to unit, and void warranty. Do not burn garbage, gasoline, drain

oil, naphtha, engine oil, railroad ties, particle board, leaves, cardboard, or any other flammable liquids.

Installation

Person (s) operating a Crown Royal Stove must comply with all applicable laws or other requirements, such as state laws or

regulations and local ordinances. Person (s) is/are also responsible for operation in a manner that does not create a public or private

nuisance condition. The distance and stack height Greentech Manufacturing recommends and the requirements in any applicable

laws or other requirements may not always be adequate to prevent nuisance conditions due to terrain or other factors.

The EPA offers tips on how to properly use a moisture meter to test firewood before using in a wood-burning stove or fireplace. Wet

wood can create excessive smoke which is wasted fuel.

The EPA’s Burnwise Program

http://www.epa.gov/burnwise

How to Use a Moisture Meter Video

http://www.youtube.com/watch?v=jM2WGgRcnm0

The EPA offers four simple steps to properly dry firewood before using in a wood-burning stove or fireplace. Wet wood can create

excessive smoke which is wasted fuel. Burning dry, seasoned firewood with a moisture content of 20% or less can save money and

help reduce harmful air pollution.

Split, Stack, Cover and Store Video

http://www.youtube.com/watch?v=yo1--Zrh11s

This tri-fold brochure provides colorful illustrations of the four easy steps to dry firewood.

Wet Wood is a Waste Brochure

http://www.epa.gov/burnwise/pdfs/wetwoodwastebrochure.pdf

ADDITIONAL INSTALLATION AND OPERATIONAL CONSIDERATIONS

The quality of the firewood you burn can have a big effect on the overall performance and efficiency of your furnace. The main

factors that affect the burning characteristic of firewood are moisture, tree species, and size. It is important that you understand

and follow our guidelines when choosing wood as a fuel source.

Fresh cut wood will have a moisture content between 35 and 50 percent by weight. If you try to burn wet wood, it will not only be

difficult to ignite but will hiss and sizzle in the firebox. Burning wet wood consumes energy that will normally be used to efficiently

complete the combustion process. Properly seasoned wood will ignite easily and burn efficiently. Hardwoods like oak and maple dry

more slowly than softer woods like spruce and poplar. Properly seasoned wood would have a moisture content of less than 20%.

Firewood dries slowly and may take a full year or more to season.

Ways to tell if firewood is dry enough to burn:

•Test wood with a moisture meter. Moisture meters can be purchased at a local hardware store for around $25.00.

•Wood darkens with aging, from white or cream in color to yellow or gray.

•There are cracks in the end grain.

•Banging two pieces together, dry wood sounds hollow. While wet wood sounds dull.

•Split a piece and if the fresh surface feels damp and cool, the wood is wet. If it feels dry and warm it is seasoned.

•When you burn it, if it hisses, it is too wet.

Types of Wood:

Wood can be classified as softwood or hardwood. Pines, spruces and firs are common softwoods and oaks, elms, birches, and

maples are hardwoods. Softwoods burn rapidly and are more resinous than the hardwoods; therefore, they will cause a greater

creosote build-up. Hardwoods produce a long-lasting fire with uniform heat. Hardwoods are the most desirable and are used by the

majority of wood burners.

Proper Wood Storage:

1. Cut the wood to the desired length. It should easily fit in your firebox.

2. Split your wood before stacking it –Splitting the wood in advance of stacking it increases exposure to air, which improves

drying time.

3. Check the moisture content –Place the moisture meter tip into the longest side of a piece of split wood. (Goal is 20%

moisture content)

4. Stack your wood in alternate directions –Spacing is needed to provide better circulation and helps in the drying process.

5. Store your wood off the ground –Store wood six inches or more off the ground to prevent moisture.

6. Cover wood, but leave the sides exposed –Use a tarp or best option is to build a structure that has a roof. If using a tarp,

make sure your sides are open, so moisture is not trapped.

7. Properly seasoned wood could take up to 12 months or more to dry.

8. Storage of your wood must be in a debris free, dry environment that is at least sixty (60) inches from the front of the stove

and thirty-six (36) inches from the sides or back of the stove.

Purchasing Wood:

A cord of wood is a ranked stack of logs 4’ x 4’ x 8’. Usually when you purchase firewood, it is sold by the “face cord”. A face cord is

a ranked stack of logs 4 feet high, 16 inches deep and 8 feet long. Wood is sometimes sold by the ton; a ton of dry hardwood is

equivalent to approximately ½ full cord. Whenever possible it is best to burn hardwood that has been split and air dried for one

year.

GUIDE TO BURNING WOOD

•All installation and operation must follow federal, provincial, state, and local codes for wire plumbing, and installing a

chimney.

•All work must be performed by qualified personnel only.

•Read and understand all precautions before operating the furnace.

•The furnace is not to be used as a standalone unit. It is recommended that a backup system be in place.

•Retain this manual for as long as you own your Crown Royal Stove. Carefully read and follow these directions.

•Regularly read over this manual to keep you informed.

WARNINGS!!

•All installations and operations of your furnace must follow STATE, PROVINCIAL and LOCAL LAWS pertaining to operations,

wiring, plumbing, and building codes. The installation must be performed by a qualified installer.

•Only burn wood in this unit. (Check with provincial, state and local regulations that obtain to banned fuels in designated

locations.)

•Only use wood with 20% or less moisture content.

•Do not install this unit on a combustible surface.

•All models operate at atmospheric pressure. DO NOT obstruct, block or plug the overflow vent tube in any way, which is

located on top of the furnace.

•This unit cannot be hooked to a chimney that is already serving another appliance. When installing a chimney that is higher

than twelve feet, guidelines must be used.

•This unit must never be pressurized.

•Do not use an automatic stoker with this unit.

•Risk of fire: Do not operate with fuel loading heat exchanger door or secondary combustion door open.

•Do not store fuel or other combustible materials within marked installation clearances.

•Inspect, clean flues and chimney regularly.

•All cover plates, enclosures, and guards must be always maintained in place, except during maintenance and servicing.

CAUTIONS!!!

•Hot Surfaces: Keep children away. Do not touch during operation.

•Do not start or operate furnace without checking heating fluid.

•Check for buried cables and utility lines before digging trench.

•For safety and proper temperature control, keep fuel door closed tightly during operation.

•Do not fire up furnace until filled with water.

•Do not start the unit during a prolonged power failure

•Load fuel carefully to avoid injury to hands, fingers and other body parts that may come in contact with the unit’s loading

door opening.

•Cleaning of the heat exchanger, flue pipe, chimney and combustion motor if used, is especially important at the end of the

heating season to minimize corrosion during the summer months caused by accumulated ash.

•Do not open secondary combustion door while in operation. Doing so will result in fire hazard and/or severe burns.

•Always check for adequate water levels.

SAFETY INSTRUCTIONS & PRECAUTIONS

DANGER!!! Do not start fire with chemicals, volatile fluids, rubber, plastics or garbage. Some processed wood can

contain resins and should be avoided. Only competent persons with a sound understanding of this heating method

should operate this furnace. Improper firing could result in personal injury and/or damage to unit, and void

warranty. Do not burn garbage, gasoline, drain oil, naphtha, engine oil, railroad ties, particle board, leaves,

cardboard, or any other flammable liquids.

Please read and follow these precautionary labels that are also found on the outdoor furnace.

PRECAUTIONARY LABELING

The quality of the firewood you burn can have a big effect on the overall performance and efficiency of your furnace. The main

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Crown Royal Stoves Herd Handbücher

Crown Royal Stoves

Crown Royal Stoves RS7200E Bedienungsanleitung

Crown Royal Stoves

Crown Royal Stoves RS7200 Bedienungsanleitung

Crown Royal Stoves

Crown Royal Stoves RS7300MP Gebrauchsanweisung

Crown Royal Stoves

Crown Royal Stoves RS7300E Bedienungsanleitung

Beliebte Herd Handbücher anderer Marken

Arada

Arada Cassette Stove Bedienungsanleitung

Parmco

Parmco FS 600 Bedienungsanleitung

MCZ

MCZ SUITE AIR 10 M2 Bedienungsanleitung

HearthStone

HearthStone Stowe DV 8321 Fehlerbehebungshandbuch

Cattara

Cattara FAMILY Bedienungsanleitung

Stanley

Stanley Argon F500 OVAL Bedienungsanleitung

Avalon

Avalon B-VENT Bedienungsanleitung

Nordpeis

Nordpeis Vega Bedienungsanleitung

Exquisit

Exquisit EKC601-5 Bedienungsanleitung

Stanley

Stanley Oisin Oil MK II Betriebsanleitung

Thermocet

Thermocet Brookfield S/CC Bedienungsanleitung

HASE

HASE delhi Bedienungsanleitung

Vermont Castings

Vermont Castings Intrepid 2 Bedienungsanleitung

Italiana Camini

Italiana Camini CLASSICA Kurzanleitung

Avalon

Avalon Vashon Avanti DVS FS Bedienungsanleitung

Spartherm

Spartherm ambiente a1 Bedienungsanleitung

Dimplex

Dimplex MCFSTV12AU Bedienungsanleitung

Warmlite

Warmlite WL46040 Bedienungsanleitung