Crypto F330 Bedienungsanleitung

USERS MANUAL

F330

ADSL ROUTER

Table of Contents

1. Introduction 4

2. Specifications 4

2.1 System requirements 4

2.2 ADSL Standards supported (Annex A & B): 4

2.3 Ports for Connectivity 4

2.4 LED’s 4

2.5 Back Panel Connectors 5

2.6 Software Features 5

3. Hardware Installation Procedures 6

3.1 Network Ethernet cable Setup 6

3.2 Powering on the F330 ADSL Router 6

4. Software Configuration Procedures 7

4.1 Preparing your network information 7

4.2 Setup your TCP/IP parameters for Window XP 8

4.3 Connection through LAN 9

4.4 USB Driver Installation under Windows XP 10

4.5 Router Protocol setup 11

5. Troubleshooting 15

1. Introduction

F330 ADSL Router is high-speed ADSL device and is a complete solution for

home and office use. The F330 ADSL Router can have a maximum downstream

data rate of up to 8Mbps and an upstream of up to 1Mbps. When configured as

a DHCP server, it will assign IP address to every connected PC and acts as the

only externally recognized Internet device on your local area network. With built-

in NAT, F330 ADSL Router serves as an Internet firewall, protecting your network

from being accessed by outside users. You can safely enjoy the new generation

broadband Internet with the F330 ADSL Router.

2. Specifications

2.1 System requirements

ñPentium II 233 MHz processor

ñ32 MB RAM minimum memory

ñ20 MB minimum available disk space on hard drive

ñEthernet Network Interface Controller (NIC) RJ45 port

ñOr 1 USB port

ñCD-ROM

2.2 ADSL Standards supported (Annex A & B):

ñANSI T1.413 Issue 2

ñITU-T G.992.1(G.DMT)

ñG.992.2 (G.LITE)

2.3 Ports for Connectivity

ñOne RJ-45 for 10/100 Base-T Ethernet

ñOne RJ-11 for ADSL line

ñOne AC power jack for power supply

ñOne USB port

2.4 LED’s

ñADSL – Indicates active synchronized ADSL connection / non

synchronized when blinking

ñDATA – Indicates active data transmission session

ñLAN - Indicates an active Ethernet connection

ñUSB – Indicates an active connection by USB

ñPWR– Indicates the router is powered on.

2.5 Back Panel Connectors

Table 2 shows the function of each connector of the F330 ADSL

Router’s back panel. Figure 1 illustrates the connectors.

Table 2: Function Description of Connectors

Connector Description

LINE Connects to your ADSL-ready telephone line

USB Connects to the USB port of your computer

RESET Resets the ADSL router to its default values

LAN

RJ-45 (Ethernet Cable) connection to your PC, or HUB

AC 9V Connects to your ADSL router 12V AC power adaptor

Figure1: Rear View of the F330 ADSL Router

2.6 Software Features

ADSL Compliant

ñANSI T1.413 issue 2

ñITU G.dmt (G.992.1)

ñITU G.lite (G.992.2)

ñG.994.1 (G.hs, Multimode)

ñADSL over POTS (Annex A) or ADSL

over ISDN (Annex B / UR2)

ñTone detection for low power mode

ñMaximum downstream rate up to 8 Mbps

ñMaximum upstream rate up to 1 Mbps

ATM

ñATM Forum UNI 3.1/4.0 PVC

ñUp to 8 VCs (Virtual Circuit)

ñATM SAR (Segmentation and Reassembly)

ñATM supports AAL5, UBR & CBR

ñRFC 2516 (PPP over Ethernet)

ñRFC 2364 (PPP over ATM)

ñRFC 1577 (Classical IP over ATM)

ñRFC 1483 BPDU (Bridge Ethernet over ATM)

ñOAM F4 and F5 segment end-to-end

loopback (F4 on all VPIs, F5 on VPI 0 only)

Bridging / Routing

ñEthernet to ADSL self-learning

Transparent Bridging (IEEE 802.1D)

ñSupports up to 128 MAC learning

address

ñIP routing-RIPv2 (backward compatible

with RIPv1)

ñStatic IP routing

ñDHCP (Dynamic Host Configuration

Protocol) Server and Client

ñNAPT (Network Address and Port

Translation)

ñNAT (Network Address Translation)

ñPAT (Port Address Translation)

ñICMP (Internet Control Message

Protocol)

ñIGMP (Internet Group Management

Protocol)

ñSimultaneous USB and Ethernet

operation

Security

ñPAP (Password Authentication Protocol)

ñCHAP (Challenge Authentication

Protocol)

ñUser authentication for PPP

ñPassword Protected System

Management

ñFirewall

HTTP Web-based management

ñFirmware upgrade

ñConfiguration of NAT/NAPT

ñWAN and LAN connection statistics

ñSelection of Bridge or Router Mode

ñConfiguration of VCs (Virtual Circuits)

ñCustomized Web pages

3. Hardware Installation Procedures

1. Plug the power cable into the back of the unit.

2. Connect the Ethernet cable (refer to section 3.1).

3. Connect the telephone line to the line socket of the router.

3.1 Network Ethernet cable Setup

You can choose to connect your ADSL Router to a single computer through

either an Ethernet LAN card through a crossover cable or a USB cable

(Figure 2), or to connect it to a Switch/HUB through a usual cable (Figure 3).

Please refer to the following figures:

Figure 2: Single User Connection example (LAN or USB)

Figure 3: Multi-user Connection with hub example (LAN)

3.2 Powering on the F330 ADSL Router

Note! Use only the manufacturer-approved power supply that shipped

with the F330 ADSL Router

Connect the power to the F330 ADSL Router by plugging the power supply

into an appropriate electrical outlet.

4. Software Configuration Procedures

4.1. Preparing your network information

To configure your ADSL router smoothly, it is required that you contact your ISP

(Internet Service Provider) and acquire the following information:

Type of Mode Encapsulation used:

ñPPPoE, PPPoA, IPoA, Bridged, or Routed.

ñAnnex A (ADSL over PSTN) or Annex B (ADSL over ISDN)

DSL connection parameters:

ñFor PPPoE or PPPoA, refer to Table 3 and fill-in all values (provided by your ISP).

ñFor Bridged, Routed, or IPoA, refer to Table 4 and fill-in all values (provided

by your ISP).

Table 3 (PPPoE/PPPoA Parameters).

Information Values

PVC Settings VPI

VCI

Encapsulation (LLC or VC Mux)

Password

IP Information Preferred DNS address

Alternate DNS address (If available)

Table 4 (Bridged/Routed/IPoA Parameters)

Information Values

PVC Settings VPI

VCI

Encapsulation (LLC or VC Mux)

IP Information IP Address

Subnet Mask

Gateway IP Address

Preferred DNS address

Alternate DNS address (If available)

NOTE: THIS MANUAL CONSISTS OF PROCEDURES ONLY FOR PPPoA

MODE

4.2 Set up your TCP/IP parameters for Windows XP

Step 1:

Click on

"Start --> Control Panel”.

Step 2:

Click on

" Switch to Classic View ".

Step 3:

Double click on "Network

Connections" to continue.

Step 4:

Single right click on " Local Area

connection " then click

" Properties ".

Step 5:

Double click on " Internet Protocol (TCP/IP) ".

Step 6:

Check " Obtain an IP address automatically "

and “Obtain DNS server address automatically”

then click on " OK " to continue.

Step 7:

Click " Show icon in notification area when

connected " then Click on " OK " to

complete the setup procedures.

4.3 Connection through LAN

You can connect the F330 directly to your computer through the LAN port, if

you have a LAN card in your PC, by using a crossover cable (included in the

package).

If you have a LAN network with more than one user, then you must connect

the F330 Router to the HUB/Switch of your network.

For the next step refer to point 4.5.

4.4 USB Driver Installation under Windows XP

Step-1:

Connect the F330 to the computer by

using the USB cable. Windows will

detect a new hardware. Click Cancel

Insert the CD and the next window

(Step 02) will appear.

Step -2:

Click “Install USB Driver”

The procedure will automatically

install the USB

Step -3:

To complete installation click “OK”

To ensure that the F330 has been

successfully installed, open the Device

Manager which is located in the Control

Panel and check to see the following.

"Crypto F330 ADSL ROUTER Adapter"

"Crypto F330 ADSL ROUTER Interface"

Inhaltsverzeichnis

Andere Crypto Netzwerk-Router Handbücher

Crypto

Crypto WF200 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise