Crystal Vision Smart DA Bedienungsanleitung
Crystal Vision Ltd., Lion Technology Park, Station Road East, Whittlesford, Cambridge, CB22 4WL, England.
E-mail: [email protected] Website: www.crystalvision.tv Tel: +44(0) 1223 497049 Fax: +44(0) 1223 497059
Smart DA
Monitoring Distribution Amplifier
Smart DA User Manual R1.1 Crystal Vision
Smart DA User Manual R1.1 117/01/07
Contents
1 Introduction 3
2 Hardware installation 4
2.1 Rear modules and signal I/O 4
Rear module connections with RM01 4
Rear module connections with RM18 5
Rear module connections with RM02 6
2.2 General Purpose Interface (GPI) 7
3 Card edge operation 11
3.1 Card-edge switch settings 11
3.2 Reading card edge LEDs 12
4 Using the active front panel 13
4.1 Module selected 13
Updating the display 15
The Smart DA active panel menu structure 16
Selecting audio group 17
Configuring alarm delay 18
Status 19
5Statesman 20
5.1 Statesman operation 20
Selecting a monitoring audio group 21
EDH status 21
Signal status 21
Set up 22
Configuring delay 22
Smart DA User Manual R1.1 Crystal Vision
Smart DA User Manual R1.1 217/01/07
6 Trouble shooting 23
6.1 Card edge status LEDs 23
Basic fault finding guide 24
7 Specification 25
Revision 1 Statesman GUIs and descriptions updated. 17-01-07
Crystal Vision Introduction
Smart DA User Manual R1.1 317/01/07
1 Introduction
Smart DA is an SDI distribution amplifier with on board signal monitoring facilities.
Combined with an active front panel or Statesman PC control system, both video and
embedded audio status can be viewed. Depending on the rear module used, Smart DA
will give either five or eight SDI outputs.
Smart DA intelligent Distribution Amplifier
Smart DA monitors the following parameters:
•Input present
•Input standard
•Video black
•Video frozen
•Audio group present
•Audio silence
•EDH monitoring, missing, full field error and active picture error.
•GPI output of selected alarms
Smart DA is a 100mm x 266mm module, which fits in Crystal Vision’s four standard
frames and can be integrated with any boards from the company’s full product range. It
can be used with three different frame rear modules, with the RM01 giving five SDI
outputs and the RM02 and RM18 both giving eight.
Applications include immediate indication of signal or transmission problems in large
systems especially in unmanned automatic playout facilities or as a simple signal probe.
Crystal Vision Hardware installation
Smart DA User Manual R1.1 417/01/07
2Hardware installation
The Smart DA single height module can be used with the RM01, RM02 and RM18 rear
connectors, which will fit into all Crystal Vision rack frames. All modules can be
connected or removed while the frame is powered, without damaging the board.
2.1 Rear modules and signal I/O
The Indigo 4 4U frame will house up to 24 single height modules with up to three power
supplies. The Indigo 2 and FR2AV 2U frames will house up to 12 single height modules
and dual power supplies. The Indigo 1 and FR1AV 1U frames will house six single height
modules and a single power supply. The Indigo DT DTBAV and DTBAV desk top boxes
both have a built-in power supply and will house up to two single height modules.
Note: For details of fitting rear connectors please refer to the appropriate frame manual
Rear module connections with RM01
RM01 fits in all frames Description
RM01
•24 Smart DA modules per
Indigo 4 frame
•12 per Indigo 2 or FR2AV
frame
•Six per Indigo 1 or FR1AV
frame
•Two per Indigo DT
•All frame slots can be used
BNC I/O assignment
SDI OUT(1) Reclocked SDI output
SDI IN SDI input
SDI OUT(2) Reclocked SDI output
SDI OUT(3) Reclocked SDI output
SDI OUT(4) Reclocked SDI output
SDI OUT(5) Reclocked SDI output
Crystal Vision Hardware installation
Smart DA User Manual R1.1 517/01/07
Rear module connections with RM18
RM18 fits in all frames Description
RM18
•12 Smart DA modules per Indigo
4 frame
•Six per Indigo 2 or FR2AV
frame
•Six per Indigo 1 or FR1AV
frame
•Two per Indigo DT
•Card fits in upper slot
•No card fits in lower slot
BNC I/O assignment
AN/C
BSDI input
CRe-clocked SDI output
DRe-clocked SDI output
ERe-clocked SDI output
FRe-clocked SDI output
GN/C
HRe-clocked SDI output
IRe-clocked SDI output
JRe-clocked SDI output
KN/C
LRe-clocked SDI output
Crystal Vision Hardware installation
Smart DA User Manual R1.1 617/01/07
Rear module connections with RM02
RM02 fits in a 2U Indigo or FR2AV frame Description
RM02
•12 Smart DA modules per
Indigo 4 frame
•Nine modules per 2U frame
•Three modules per rear
connector
•Nine connections available
•Card 1 fits in slots 1, 5 and 9
•Card 2 fits in slots 2, 6 and 10
•Card 3 fits in slots 4, 8 and 12
•No card fits in 3, 7 or 11
BNC I/O assignment
SDI IN SDI input
1Reclocked SDI output
2Reclocked SDI output
3Reclocked SDI output
4Reclocked SDI output
5Reclocked SDI output
6Reclocked SDI output
7Reclocked SDI output
8/IN2 Reclocked SDI output
Crystal Vision Hardware installation
Smart DA User Manual R1.1 717/01/07
2.2 General Purpose Interface (GPI)
Each frame slot has up to six connections ‘a-f ‘for GPI control and monitoring. These
connections are available at the rear of the frame on the 26-way D type Remote
connectors.
GPI Default Statesman configured Low (<1V) High (+5V)
1‘a’ Input Missing
2‘b’ Input frozen or
black See table. Alarm condition Non- alarm
3‘c’ No function
4‘d’ No function
5‘e’ No function
6‘f’ No function
As supplied, each GPI output has a 220Ωresistor in series with its output. This allows for
an external LED to be driven, connected to a DC voltage of +5V.
GPI 1 and GPI 2 can be configured to show an alarm condition for any individual or
group of error conditions. Configuration of the GPI reporting can only be carried out
using either an active control panel or Statesman.
Reportable error conditions
Silence from any channel 1-4 of selected group for
longer than set interval
Video input not present
Video input standard changed
Video picture black for longer than set interval
Video picture frozen for longer than set interval
EDH error
EDH missing
Note. When set to local control, GP1 input present/missing will react immediately to a loss of input
signal. GP2 will report an error only if any of the monitored parameters are incorrect for approximately
30 seconds. Error delay is not variable in local mode.
Crystal Vision Hardware installation
Smart DA User Manual R1.1 817/01/07
4U frame GPI connections
GPI lines ‘a’ to ‘f’ of each card connect to one of eight rear remote connectors as follows:
Slot no. ‘a’ pin ‘b’ pin ‘c’ pin ‘d’ pin ‘e’ pin ‘f’ pin
18 (1) 9 (1) 18 (1) 26 (1) 19 (2) 20 (2)
27 (1) 16 (1) 17 (1) 25 (1) 10 (2) 11 (2)
38 (3) 9 (3) 18 (3) 26 (3) 19 (4) 20 (4)
47 (3) 16 (3) 17 (3) 25 (3) 10 (4) 11 (4)
55 (1) 6 (1) 15 (1) 24 (1) 1 (2) 2 (2)
64 (1) 14 (1) 13 (1) 23 (1) 3 (2) 4 (2)
75 (3) 6 (3) 15 (3) 24 (3) 1 (4) 2 (4)
84 (3) 14 (3) 13 (3) 23 (3) 3 (4) 4 (4)
93 (1) 12 (1) 22 (1) 21 (1) 12 (2) 13 (2)
10 10 (1) 11 (1) 19 (1) 20 (1) 21 (2) 22 (2)
11 3 (3) 12 (3) 22 (3) 21 (3) 12 (4) 13 (4)
12 10 (3) 11 (3) 19 (3) 20 (3) 21 (4) 22 (4)
Slot no. ‘a’ pin ‘b’ pin ‘c’ pin ‘d’ pin ‘e’ pin ‘f’ pin
18 (5) 9 (5) 18 (5) 26 (5) 19 (6) 20 (6)
27 (5) 16 (5) 17 (5) 25 (5) 10 (6) 11 (6)
38 (7) 9 (7) 18 (7) 26 (7) 19 (8) 20 (8)
47 (7) 16 (7) 17 (7) 25 (7) 10 (8) 11 (8)
55 (5) 6 (5) 15 (5) 24 (5) 1 (6) 2 (6)
64 (5) 14 (5) 13 (5) 23 (5) 3 (6) 4 (6)
75 (7) 6 (7) 15 (7) 24 (7) 1 (8) 2 (8)
84 (7) 14 (7) 13 (7) 23 (7) 3 (8) 4 (8)
93 (5) 12 (5) 22 (5) 21 (5) 12 (6) 13 (6)
10 10 (5) 11 (5) 19 (5) 20 (5) 21 (6) 22 (6)
11 3 (7) 12 (7) 22 (7) 21 (7) 12 (8) 13 (8)
12 10 (7) 11 (7) 19 (7) 20 (7) 21 (8) 22 (8)
Table shows pin number (Remote number)
Note: Remote 1, Remote 3, Remote 5 and Remote 7 are 26 way high-density D-Type female
sockets. Frame ground is pin 2 and +5V @500mA is pin 1 in each case.
Remote 2, Remote 4, Remote 6 and Remote 8 are 26 way high-density D-Type male plugs
and frame ground is pin 6 in each case and +5V @500mA is pin 15 on Remote 2 and Remote
6.
Note. The +5V output is protected by self-resetting thermal fuses, which limit the total output
current available from Remotes 1-4 to approximately 1A. Remotes 5-8 are similarly
protected.
UpperLower
Crystal Vision Hardware installation
Smart DA User Manual R1.1 917/01/07
2U frame GPI connections
GPI lines ‘a’ to ‘f’ of each card connect to one of four rear remote connectors as follows:
Slot no. ‘a’ pin ‘b’ pin ‘c’ pin ‘d’ pin ‘e’ pin ‘f’ pin
18 (1) 9 (1) 18 (1) 26 (1) 19 (2) 20 (2)
27 (1) 16 (1) 17 (1) 25 (1) 10 (2) 11 (2)
38 (3) 9 (3) 18 (3) 26 (3) 19 (4) 20 (4)
47 (3) 16 (3) 17 (3) 25 (3) 10 (4) 11 (4)
55 (1) 6 (1) 15 (1) 24 (1) 1 (2) 2 (2)
64 (1) 14 (1) 13 (1) 23 (1) 3 (2) 4 (2)
75 (3) 6 (3) 15 (3) 24 (3) 1 (4) 2 (4)
84 (3) 14 (3) 13 (3) 23 (3) 3 (4) 4 (4)
93 (1) 12 (1) 22 (1) 21 (1) 12 (2) 13 (2)
10 10 (1) 11 (1) 19 (1) 20 (1) 21 (2) 22 (2)
11 3 (3) 12 (3) 22 (3) 21 (3) 12 (4) 13 (4)
12 10 (3) 11 (3) 19 (3) 20 (3) 21 (4) 22 (4)
Table shows pin number (remote number)
Note: Remote 1 and Remote 3 are 26 way high-density D-Type female sockets. Frame ground is
pin 2 and +5V @500mA is pin 1 in each case.
Remote 2 and Remote 4 are 26 way high-density D-Type male plugs and frame ground is pin
6 in each case and +5V @500mA is pin 15 on Remote 2.
Note. The +5V output is protected by self-resetting thermal fuses, which limit the total output
current available from Remotes 1-4 to approximately 1A.
1U frame GPI connections
GPI lines ‘a’ to ‘f’ of each card connect to one of two rear remote connectors as follows:
Slot no. ‘a’ pin ‘b’ pin ‘c’ pin ‘d’ pin ‘e’ pin ‘f’ pin
18 (1) 9 (1) 18 (1) 26 (1) 19 (2) 20 (2)
27 (1) 16 (1) 17 (1) 25 (1) 10 (2) 11 (2)
35 (1) 6 (1) 15 (1) 24 (1) 1 (2) 2 (2)
44 (1) 14 (1) 13 (1) 23 (1) 3 (2) 4 (2)
53 (1) 12 (1) 22 (1) 21 (1) 12 (2) 13 (2)
610 (1) 11 (1) 19 (1) 20 (1) 21 (2) 22 (2)
Table shows pin number (remote number)
Note: Remote 1: 26 way high-density D-Type female socket. Frame ground is pin 2 and +5V
@500mA is pin 1.
Remote 2: 26 way high-density D-Type male plugs and frame ground is pin 6 and +5V
@500mA is pin 15
Note. The +5V output is protected by self-resetting thermal fuses, which limit the total output
current available from Remotes 1-2 to approximately 1A.
Inhaltsverzeichnis
Andere Crystal Vision Verstärker Handbücher
Crystal Vision
Crystal Vision Indigo AADA416FM Bedienungsanleitung
Crystal Vision
Crystal Vision 3GDA-VF Bedienungsanleitung
Crystal Vision
Crystal Vision VDA110M Bedienungsanleitung
Crystal Vision
Crystal Vision HDDA104R Bedienungsanleitung
Crystal Vision
Crystal Vision ViPA204 Bedienungsanleitung
Crystal Vision
Crystal Vision 3GDA204R Bedienungsanleitung
Crystal Vision
Crystal Vision Indigo 3GDA105 Bedienungsanleitung
Crystal Vision
Crystal Vision Indigo VDA210M HD Bedienungsanleitung
Crystal Vision
Crystal Vision Indigo AADA-STM-1 Bedienungsanleitung
Crystal Vision
Crystal Vision AADA-VF Bedienungsanleitung
Crystal Vision
Crystal Vision DADA-VF Bedienungsanleitung
Crystal Vision
Crystal Vision DDA108A Bedienungsanleitung
Crystal Vision
Crystal Vision HDDA105 Series Bedienungsanleitung
Crystal Vision
Crystal Vision Indigo 3GDA105R Bedienungsanleitung
Crystal Vision
Crystal Vision VDA110M Bedienungsanleitung
Crystal Vision
Crystal Vision VDA110R Bedienungsanleitung
Crystal Vision
Crystal Vision AADA416FR Bedienungsanleitung
Crystal Vision
Crystal Vision DDA208B Bedienungsanleitung
Crystal Vision
Crystal Vision Indigo VDA210M HD Bedienungsanleitung
Crystal Vision
Crystal Vision VDA110R Bedienungsanleitung
