CTC Union STE-10 Bedienungsanleitung

OPERATION MANUAL

Table of Contents

CHAPTER 1

1.0 Introduction ..................................................................... 1

1.1 Features ………………………………………………….. 1

1.2 Specifications ................................................................... 2

1.3 Configuration ................................................................... 4

1.4 Configuration with Telnet ................................................. 8

1.5 Raw Data Server Mode .................................................... 9

1.6 Telnet IAC Data Server Mode ......................................... 16

1.7 Terminal Server Mode .................................................... 17

1.8 Auto Connect After Power Up Mode .............................. 20

CHAPTER 2

2.0 Application Examples ...................................................... 23

2.1 Raw Data Server Application ....................................... 23

2.2 Terminal Server Application ........................................ 24

2.3 Auto Connect Application ........................................... 26

APPENDIX

A.1 RS-232 Port Pin Definition ............................................. 29

A.2 RJ-45 Ethernet Pin Definition ......................................... 29

A.3 Null Modem Cable Pinout ............................................... 30

Table of Contents

This page left blank intentionally.

Chapter 1: Configuration and Operation

1.0 Introduction

The STE-10 Serial Access Unit is a low cost, compact, serial

access server or terminal server for connecting asynchronous serial

devices (RS-232) over Ethernet (10Base-T) using a TCP/IP protocol

stack. The STE-10 may operate in either a client mode or as a server,

allowing connection of serial data directly over a LAN or WAN.

Configuration may be performed either via the DB25 pin RS-232 port

with an ASCII terminal or via Telnet and Ethernet connection on the

RJ-45 LAN port. The serial port is DTE, which allows direct

connection to DCE equipment such as Modems. For connection to

other DTE equipment such as a PC or terminal, a NULL Modem or

crossover cable is required. One is provided with the unit.

1.1 Features

•Low cost, compact design.

•Serial connection over Ethernet.

•Operates in either server or client mode.

•Complete TCP/IP protocol stack (OSI Network Layer 3).

•Provides packetization of serial data.

Chapter 1: Configuration and Operation

1.2 Specifications

Hardware

•CPU Intel® 80188

•ROM 256K bytes Flash

•RAM 256K bytes DRAM

•LAN Interface IEEE802.3 10Base-T Ethernet, RJ-45

connector, DTE connection straight to HUB

•Serial interface EIA RS-232 ASYNC, DB25M connector

•Baud rates 1200, 2400, 4800, 9600, 19200, 38400,

57600, 115200, 230400, or 460800

•Data length 5, 6, 7, or 8 bits

•Parity None, Odd, or Even

•Stop bits 1 or 2 bits

•Handshaking None, RTS/CTS, or Xon/Xoff

Software

•Flash ROM Boot without network host; provision for easy

software upgrades

•Protocols TCP/IP, ARP, ICMP protocols

•Functions Telnet / Reverse Telnet

•Configuration Telnet or ASCII terminal direct or via Dial-in

•LED indicators Power, LAN Tx/Rx, Serial Tx and Rx

Chapter 1: Configuration and Operation

Ethernet connection: straight cable to HUB,

crossover cable to NIC

Ethernet activity indicator LED

Connect to

AC Adapter

Power

indicator

LED

RS-232 activity

LED indicators

RS-232 Async Port

D-type 25 pin Male

Config.

Switch

Chapter 1: Configuration and Operation

1.3 Configuration

Before any Ethernet connection is made to the STE-10, the

device must have a valid IP address, which is accessible through the

network. Initial IP setting is accomplished with a terminal connection

to the RS-232 serial port. Connect a serial terminal to the RS-232 port

of the STE-10 at 9600 baud, 8 bits, no parity and 1 stop bit. Since the

STE-10 is DTE and a terminal is also DTE, please use the provided

crossover cable. Set the configuration switch on the STE-10 to

"SETUP" and apply power.

If a serial terminal is not available, a PC with Windowsmay be

used along with the HyperTerminalprogram. To start and configure

HyperTerminalfollow these simple steps:

Using your mouse, browse to HyperTerminal; Start =>Programs

=>Accessories =>Communications =>HyperTerminal.

Double-click the "Hypertrm.exe" icon. Enter a name (such as

STE-10) and choose an icon for the connection. When the "Connect

to" dialogue box appears, click the down arrow on the "Connect

using:" pull-down tab and select "Direct to COMx" where "x" is the

COM port number that will connect to the STE-10.

Click the "OK" button and set the COM port parameters for; 9600

baud, 8 bits, no parity, 1 stop bit and no flow control. Refer to the

following page graphic.

Chapter 1: Configuration and Operation

Example of port setting under HyperTerminal.

An initial message like the one below will be displayed while the

port checks whether it is connected to a modem, followed by the main

configuration menu display.

CHECKING MODEM ABOUT 10 SECONDCHECKING MODEM ABOUT 10 SECOND

AT&C1V1AT&C1V1

Chapter 1: Configuration and Operation

If your connection is a direct one, your terminal should display

the first menu for the STE-10.

SERIAL DEVICE SERVERSERIAL DEVICE SERVER

a). DEVICE SETTINGSa). DEVICE SETTINGS

b). UPGRADE FIRMWAREb). UPGRADE FIRMWARE

c). GENERAL DIAGNOSTICc). GENERAL DIAGNOSTIC

SELECT:SELECT:

Main configuration menu, terminal mode.

Select option a): Device Settings

DEVICE SETTINGSDEVICE SETTINGS

a). DEVICE IP ADDRESSa). DEVICE IP ADDRESS <192.168.2.1><192.168.2.1>

b). DEVICE SUBNET MASKb). DEVICE SUBNET MASK <255.255.255.0><255.255.255.0>

c). DEVICE NAMEc). DEVICE NAME <STE-10><STE-10>

d). DEVICE PASSWORDd). DEVICE PASSWORD <><>

e). MODE SETTINGSe). MODE SETTINGS <<RAW SERVER>RAW SERVER>

f). GATEWAY ADDRESSf). GATEWAY ADDRESS <0.0.0.0><0.0.0.0>

g). LOAD DEFAULT SETTINGSg). LOAD DEFAULT SETTINGS

h). APPLY AND SAVE SETTINGSh). APPLY AND SAVE SETTINGS

q). PREVIOUS MENUq). PREVIOUS MENU

SELECT:SELECT:

Inhaltsverzeichnis

Andere CTC Union Netzwerk-Hardware Handbücher

CTC Union

CTC Union SC150 Series Bedienungsanleitung

CTC Union

CTC Union IMC-100-PD Bedienungsanleitung

CTC Union

CTC Union FRM220-TM-10GMUX Bedienungsanleitung

CTC Union

CTC Union INJ-G30 Bedienungsanleitung

CTC Union

CTC Union FMUX101 Bedienungsanleitung

CTC Union

CTC Union IP DSLAM for ADSL IPDSLAM-A8/A16 Bedienungsanleitung

CTC Union

CTC Union VDSM2-1524 Bedienungsanleitung

CTC Union

CTC Union IPM-E1 Series Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Lanner

Lanner NCA-1525 Bedienungsanleitung