CTRLink EIPR series Bedienungsanleitung

EIPR Series

Skorpion Wired and Wireless VPN Routers

Installation Guide

The EIPR Series provides routing between a wide-area-network (WAN) and a local-area-

network(LAN)—which features a four-port10/100 Mbps Ethernet switch. The two models

are identical except for their USB port functions. The EIPR-E can act as a Wi-Fi access

point with the connection of a Wi-Fi adapter. The EIPR-V does the same, but the USB port

can also support a cellular adapter for wireless WAN communication (in which case the

wired WAN port is automatically deactivated). The EIPR-V also adds virtual private

network (VPN) firmware and a real-time clock —sothat it can function as a VPN client.

Each port automatically negotiates with connected devices. Thus, the EIPR can provide

plug-and-playoperationwithnoconfigurationunlessrequiredforadvancedroutingfeatures

or when non-default operating parameters are required. In these cases, default behaviour

can be modified from a LAN port via its built-in web server located at 192.168.92.1. By

default, its WAN port is assigned an IP address via the built-in DHCP client. An internal

DHCP server assigns IP addresses to LAN-connected devices. Through its WAN port, the

built-in DNS forwarder passes DNS requests from a LAN host to a remote DNS server.

Powering. Aninternalhalf-waverectifierallowssharingacommonACpowersourcewithother

half-wave devices. Voltage must deliver current commensurate with 9 VA power consumption.

Power conductors should be 16–22 AWG (solid) or 16–18 AWG (stranded). Common is

connected to 0 V. Chassis is isolated from 0 V. Inputs are reverse-polarity protected.

Mechanical

LED Indicators

The “PWR” LED glows solid green when the unit is properly powered. Each Ethernet

port has two LEDs: LED “L” glows solid if a valid link exists, flashes for activity and

shows data rate by colour: green for 100 Mbps or yellow for 10 Mbps. For full-duplex,

the “D” LED is green; for half-duplex it is unlit —but flashes if a collision occurs.

Specifications

Environmental

Operating Temp: 0°C to +60°C

Storage Temp: –40°C to +85°C

Humidity: 10–95%, non-condensing

DIN-rail Mounting TS-35

Regulatory Compliance

CE Mark; CFR 47 Part 15, Class A

UL508 Industrial Control Equipment

Functional

Compliance: ANSI/IEEE 802.3

Data Rates: 10 and 100 Mbps

Signalling: 10BASE-T and

100BASE-TX

RJ-45 Pin Assignments

Pin Function

1 TD+

2 TD–

3 RD+

6 RD–

(other pins are unused)

USB Pin Assignments

Pin Function

1 +5V

2 –Data

3 +Data

4 Ground

Wired Network Connections

Auto-MDIX allows connections to other

equipment with either crossover or

straight-through cabling.

Initial Access Setup. When first installing the EIPR, its default address could match

that of a device on the Ethernet LAN and its DHCP server could interfere with your

existing LAN devices. So the EIPR and the PC used for setup should both be temporarily

disconnected from the existing LAN. The procedure for altering the IP address creates

a temporary LAN composed of nothing but the EIPR, the PC used to configure it and a

CAT5 cable connecting the two. Either straight-through or crossover cable can be used

because the EIPR supports Auto-MDIX.

Initial Access.Your EIPRwill provide aDHCP assignedIPaddresstoyour PC.Connect

the PC directly to one of the LAN ports of the EIPR. Do not connect any other devices to

anyof the other EIPR ports at this time. On your PC, access Network Connections, then

open the Properties of the Local Area Connections. Once the Properties pop-up opens,

scroll down under the General tab and select Internet Protocol (TCP/IP).When the next

pop-up opens, choose Obtain an IP address automatically.Now close the opened pop-

ups, and under System Accessories, open a Command Prompt window and type

ipconfig to confirm that your change of IP address was successful. Remember to

restore your PC’s original IP/Subnet values when you are finished setting up the EIPR.

Initial Login. When the EIPR is first powered up, or after using the Reset button, the

setup screen will be accessible from one of the LAN ports using the IP address

192.168.92.1 and a subnet mask of 255.255.255.0. In the login screen that appears, use

the default value of admin for both the Username and Password.

Setup Tab. After login, the Setup screen appears. In both the WAN and LAN portions

of the screen, set the desired values as per the resident instructions.

Administration Tab. On this screen it is recommended that you choose your own

values of Username and Password.

Status Tab. This screen displays Firmware Version, MAC Address, WAN Status and

LAN Status (including the resident DHCP server and its LAN clients, if enabled).

Advanced Tab. Here you can select and adjust the advanced features of the router

as explained in the resident help screens.

Reset Switch.The Reset Switch (located just below the Power LED) will restore

factory default settings including the IP address, netmask and subnet settings. To reset

the router to its default values, use a paperclip or similar tool to press the Settings Reset

button for at least 3 seconds while the router is powered. Then release the reset button

and remove power from the router for 3 seconds. Restore power and the unit will now

use the default IP values and the default Username and Password. Remember, upon

reset, the issues mentioned above in the paragraph that is titled Initial Access will apply!

Need More Help Installing this Product?

More information can be found in the Technical Support part of our web site

at www.ccontrols.com. If contacting our office, ask for Technical Support.

Warranty

Warranty information can be found at the URL below:

www.ccontrols.com/warranty.htm

Warning: This is a Class A product. In a domestic environment this product may cause

radio interference in which case the user may be required to take adequate measures.

Returning Products for Repair

Return the product to the location where it was purchased by following the

instructions at the URL below:

www.ccontrols.com/rma.htm

Declaration of Conformity

Information about the regulatory compliance of this product can be found at

the URL below:

www.ccontrols.com/compliance.htm

September 2013 TD070800-0ID

Inhaltsverzeichnis

Andere CTRLink Netzwerk-Router Handbücher

CTRLink

CTRLink EIPR Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise