Cub Cadet Double Bagger Bedienungsanleitung

CONTENTS OF CARTON

42”/46” Double Bagger

Before beginning installation, remove all parts from the carton to make sure

everything is present. Carton contents are listed below and shown in Figure 1. The

hardware pack(s) included in this kit are detailed at the end of this section.

• Boot Assembly - 731-09329A

• Grass Bag Assembly (2) - 664-05104

• Vertical Bagger Support - 683-04519C

• Grass Bag Support - 683-05329A

• End Plugs (4) - 735-0246A (pre-installed)

• Bagger Cover - 631-05474B

• Bagger Vent Wall Assembly - 631-05491B

• Bagger Cover Left Side Wall - 731-12350B

• Hose - 764-05082

• Lower Hose Connection - 731-12353A (pre-installed)

• Hinge Pin - 711-06701

• Adapter Bracket - 789-02518

• Hitch Adapter Bracket - 789-02298

• RZT Bagger Weight - 719-04271A

• Weight Plates (3) - 789-02137

• Weight Hanger Bracket Left - 789-02197

• Weight Hanger Bracket Right - 789-02198

• Hardware Pack - 689-01419

• Anti-marking Adhesive Strips - 777X52246

• Bagger Boot Hardware Pack - 689-00636

50”/54” Double Bagger

Before beginning installation, remove all parts from the carton to make sure

everything is present. Carton contents are listed below and shown in Figure 2. The

hardware pack(s) included in this kit are detailed at the end of this section.

• Boot Assembly - 631-05103

• Grass Bag Assembly (2) - 664-05104

• Vertical Bagger Support - 683-04519C

• Grass Bag Support - 683-05329A

• Chute Adapter - 731-10133

• End Plugs (4) - 735-0246A (pre-installed)

• Bagger Cover - 631-05474B

• Bagger Vent Wall Assembly - 631-05491B

• Bagger Cover Left Side Wall - 731-12350B

• Hose - 764-05135

• Lower Hose Connection - 731-12353A (pre-installed)

• Hinge Pin - 711-06701

• Adapter Bracket - 789-02518

• Hitch Adapter Bracket - 789-02298

• RZT Bagger Weight - 719-04271A

• Weight Plates (3) - 789-02137

• Weight Hanger Bracket Left - 789-02197

• Weight Hanger Bracket Right - 789-02198

• Hardware Pack - 689-01419

• Anti-marking Adhesive Strips - 777X52246

• Bagger Boot Hardware Pack - 689-02199

Figure 1 Figure 2

Thank You

Thank you for purchasing a bagging attachment. It was carefully engineered to provide excellent performance when properly operated and maintained.

Please read this entire manual prior to operating the equipment. It instructs you how to safely and easily set up, operate and maintain your equipment. Please be sure that you, and any other persons who will

operate the machine, carefully follow the recommended safety practices at all times. Failure to do so could result in personal injury or property damage.

All information in this manual is relative to the most recent product information available at the time of printing. Review this manual frequently to familiarize yourself with the equipment, its features and

operation. Please be aware that this Operator’s Manual may cover a range of product specifications for various models. Characteristics and features discussed and/or illustrated in this manual may not be

applicable to all models. We reserve the right to change product specifications, designs and equipment without notice and without incurring obligation.

If you have any problems or questions concerning this equipment, phone your local dealer or contact us directly. We want to ensure your complete satisfaction at all times.

Throughout this manual, all references to right and left side of the machine are observed from the operating position.

CONTENTS OF CARTON

Contents of Hardware Pack

Please check your hardware packs against the illustrations below. The quantities for each item are listed in parenthesis.

Hardware Pack 689-01419

(1)

(2) (4)

(2)

(5)

(2) (2)

(7)

(12)

710-0276

710-0376

710-3056

710-3085

712-04063

712-04065

720-04122

735-05938

736-0117

736-0242

42”/46” Hardware Pack 689-00636

738-1225 712-04064

(1)

747-06043

(2)(2)

50”/54”Hardware Pack 689-02199

(2)

712-04064

738-1225

747-06309

(2)

(1)

ASSEMBLY & INSTALLATION

NOTE: References to left, right, front and rear of the tractor are from the operator’s position, unless

otherwise stated.

• Before assembly, place the tractor on a firm, level surface, disengage the

PTO, stop the tractor engine and set the parking brake.

Assemble Mounting Brackets

1. Install 12 rubber pads (735-

05938) into adapter bracket

(789-02518) using the mounting

holes shown in Figure 3.

NOTE: Check the bumper pads after

each season for excessive wear and

replace as necessary.

Install Bracket Assembly

on Tractor

NOTE: When assembling this mounting assembly,

it is best to not fully tighten the bracket at this

time. This will facilitate the mounting process in

later steps, which will then require fully

tightening this mounting assembly.

Install mounting bracket assembly on tractor as follows:

1. Remove hitch bracket.

2. For ZT1 installation only:

Place two flat washers

(736-0117) between

hitch bracket adapter

(789-02298) and the hitch

bracket removed in Step 1.

3. Install bracket assembly to

the tractor’s lower frame

with two capscrews (710-

0376). See Figure 4.

4. Hang adapter bracket

assembly onto upper frame

square tube and connect to

hitch bracket adapter (789-

02298) with two screws

(710-0376), two cup

washers (736-0242) ,and

two flange lock nuts (710-

04063). See Figure 5.

NOTE: Make sure that the adapter

bracket is seated firmly on the

upper tube frame.

5. Tighten all of the hardware

installed at this time.

Install Vertical Support

NOTE: This manual covers various bagger configurations. Please follow the instructions

applicable to your machine.

1. Using Figure 6 and the chart below, locate the correct mounting hole location

on the mounting bracket for your tractor:

Model No. Description Position

19A70054* 42”/46” Double Bagger 4

19A70055* 50”/54” Double Bagger 3

NOTE: Hole position 2 is

currently not used.

2. Install the vertical support

bracket onto the mounting

assembly on the tractor

by hooking it over the

mounting assembly as

shown in Figure 7.

3. Secure the upright

support bracket to the

mounting assembly using

a hex bolt (710-0376)

and flange lock nut (712-

04063) from hardware

pack 689-01419. See

Figure 7.

Install Hanger Assembly

1. Install and secure the

hanger assembly onto the

upright support bracket

using two carriage bolts

(710-0276), two cup

washers (736-0242) and

two flange lock nuts (712-

04063) from hardware

pack 689-01419. See

Figure 8.

NOTE: The carriage bolts (710-0276),

from hardware pack 689-01419, go in the

top hole with the nut facing the engine.

The hex bolt (710-0376), from the same

hardware pack, goes in the bottom hole.

Install Top Bagger

Components

With the mounting brackets

assembled and in place on the

tractor, follow these steps to

assemble the remaining bagger

components.

1. If not already installed

by the factory, snap

the vent cover into the

holes found on the chute

support assembly.

Figure 3

Figure 4

Figure 5

Figure 6

Figure 7

Figure 8

ASSEMBLY & INSTALLATION

2. Snap the plastic upper chute support in place by first clipping the side

portion onto the bagger support rail (1) as shown in Figure 9.

3. Snap the front side of the chute support to the rail (2) as shown in Figure 9.

4. Snap the top cover support on to the bagger support rail at a slight angle.

Rotate the assembly down and into the chute support assembly, making sure

that the tab (shown in inset of Figure 10) is locked into place.

5. Install the bagger top cover by aligning the tabs of the cover and sliding the

mounting pin into the channel as shown in Figure 11.

6. Open hood by pushing in on the rear side tabs with your hand (1), and lifting

the cover with your other hand in the center rear of the bagger cover (2) as

shown in Figure 12.

7. Install both bag assemblies onto the bag support brackets by inserting the

front edge in first (1), and then setting the back edge down until it fits into the

assembly (2) as shown in Figure 13.

Installing the Boot Rod and Hardware

Model 19A70054*:

1. From the inside of the boot, put

the two hex head screws (738-

1225) through the holes at the

bottom front of the boot. See

Figure 14.

2. Put the mounting rod (747-06043)

in place over the hex head screws.

Make sure the tip of the rod is

facing out from the boot. See

Figure 14.

3. Begin threading the flange lock nuts (712-04064) onto the hex head screws.

See Figure 14.

4. Using a 7/16” wrench or socket on the screw and a 7/16” box wrench on the

lock nuts, tighten down so flange is flush to secure the assembly.

Model 19A70055*:

1. From the inside of the boot,

put the two hex head screws

(738-1225) through the holes at

the bottom front of the boot. See

Figure 15.

2. Put the mounting rod (747-06309)

in place over the hex head screws.

Make sure the tip of the rod is

facing out from the boot. See

Figure 15.

3. Begin threading the flange lock

nuts (712-04064) onto the hex head screws. See Figure 15.

4. Using a 7/16” wrench or socket on

the screw and a 7/16” box wrench

on the lock nuts, tighten down

so flange is flush to secure the

assembly.

Installing the Discharge

Chute - 42/46” Double

Bagger

1. With the tractor’s discharge chute

raised up and held open (1), install

the chute elbow by placing the

chute elbow mounting rod into

the chute mounting tab (2), as

shown in Figure 16.

2. Secure the chute elbow to

the deck using a wing knob

(720-04122) from hardware pack

689-01419. See Figure 17.

NOTE: If present, remove the protective

cap off of the mounting stud on the

mowing deck as shown in the upper inset

of Figure 17.

IMPORTANT: Be certain that the

bottom of the discharge chute is

located inside of the lip of the deck

opening, as shown in Figure 18.

Installing the Discharge

Chute - 50/54” Double

Bagger

When installing the discharge chute,

two different installation instructions

exist. For the 54” Fabricated deck units, the discharge chute elbow mounts directly

onto the cutting deck. For the 50” and 54” stamped decks, an adapter must first be

installed. Be sure to follow the instructions that pertain to the unit you are installing

this bagger on.

54” Fabricated Deck Units:

1. Raise the deck to its highest

position.

2. Raise the chute deflector (1 in

Figure 19) on the deck and hold it

while you position the discharge

chute over the chute opening.

Figure 14

Figure 15

Figure 16

Figure 17

Figure 18

Figure 19

Figure 9 Figure 10 Figure 11 Figure 12 Figure 13

ASSEMBLY & INSTALLATION

3. Insert the end of the discharge chute

elbow (2) into the hole provided in

the deck wheel mount as shown

in the inset of Figure 19.

4. Pivot the discharge chute

rearward until the hole in the

discharge chute elbow aligns with

the pin on the deck. Move the

discharge elbow down onto that

pin as shown in 3 of Figure 19.

5. Secure the discharge chute elbow

to the cutting deck using a wing

knob (720-04122) included with

the bagger kit. Refer to Figure 20.

On 50” and 54” Stamped Decks:

1. Raise the deck to its highest

position.

2. Remove the deck pin rubber

protective cap (1) in Figure 21.

3. Raise the chute deflector (2 in

Figure 21) on the deck and hold

it while you install the chute

adapter (731-10133) (3) onto the

deck as shown in Figure 21.

4. Insert the end of the discharge

chute elbow (1) into the hole

provided in the deck wheel mount

as shown in the inset of Figure 22.

5. Pivot the discharge chute

rearward until the hole in the

discharge chute elbow aligns

with the pin on the deck adapter.

Move the discharge elbow down

onto that pin as shown in 2 of

Figure 22.

6. Secure the discharge chute elbow

to the cutting deck using a wing

knob (720-04122) included in

hardware pack 689-01419. Refer

to Figure 23.

Installing the Upper Chute

Tube

1. Thread the upper end of the chute

tube securely into the upper chute

support. There are two tabs on

the lower inside part of the upper

chute support to allow for secure

threading. See Figure 24.

NOTE: The chute tube and upper chute

support are left-hand threaded. Thread

counterclockwise until secure.

2. Lift by the handles at the bottom

of the chute tube. Slide the

chute tube over the chute elbow

mounted on the cutting deck, as

shown in Figure 25.

3. Make sure the connection is

secure and there are no gaps

between the chute tube and the

chute elbow.

4. If open, close the grass catcher

cover prior to mowing.

Install The Counter Weight

WARNING

This front-weight kit is required when operating any compatible zero turn

tractor models equipped with a grass collector. Failure to install this kit

may result in serious injury or death.

WARNING

Before beginning installation, place the zero turn tractor on a firm and

level surface, set the parking brake, place the PTO in the disengaged

(OFF) position, stop the motor and remove the ignition key to prevent

unintended starting.

1. Before assembly, peel the

adhesive decals from the sheet

and apply to the inside faces of

the right and left weight hanger

brackets, as shown in Figure 26.

2. Attach the weight and three

weight plates to the weight

hanger brackets with two 3/8” hex

head capscrews (710-3085) and

two nuts (712-04065) as shown in

Figure 27.

3. Visually center the weight bar

assembly on the tractor and using

two 7/16” hex head capscrews

(710-3056) and two nuts (712-

04063) secure the counter weight

assembly to the tractor as shown

in Figure 28.

Figure 20

Figure 21

Figure 22

Figure 23

Figure 24

Figure 25

Figure 26

Figure 27

Figure 28

Inhaltsverzeichnis

Andere Cub Cadet Rasenmäher Handbücher

Cub Cadet

Cub Cadet LTX 1046 Bedienungsanleitung

Cub Cadet

Cub Cadet Z-Force S 60 Bedienungsanleitung

Cub Cadet

Cub Cadet 18M Bedienungsanleitung

Cub Cadet

Cub Cadet SLT1550, SLT1554 Bedienungsanleitung

Cub Cadet

Cub Cadet CC 550 ES Bedienungsanleitung

Cub Cadet

Cub Cadet 2150 Bedienungsanleitung

Cub Cadet

Cub Cadet S979 Bedienungsanleitung

Cub Cadet

Cub Cadet A00 series Bedienungsanleitung

Cub Cadet

Cub Cadet GTX 2100 Bedienungsanleitung

Cub Cadet

Cub Cadet GTX 1054 Bedienungsanleitung

Cub Cadet

Cub Cadet CC-949 Bedienungsanleitung

Cub Cadet

Cub Cadet Z-Force S Bedienungsanleitung

Cub Cadet

Cub Cadet 1529 Bedienungsanleitung

Cub Cadet

Cub Cadet THE TANK S6031 Betriebsanleitung

Cub Cadet

Cub Cadet LT1042 Bedienungsanleitung

Cub Cadet

Cub Cadet SCP21E Bedienungsanleitung

Cub Cadet

Cub Cadet LTX 1146 Bedienungsanleitung

Cub Cadet

Cub Cadet LT1042 Bedienungsanleitung

Cub Cadet

Cub Cadet Z-Force S 48 Bedienungsanleitung

Cub Cadet

Cub Cadet TANK LZ 60 KW Bedienungsanleitung

Cub Cadet

Cub Cadet 979 Bedienungsanleitung

Cub Cadet

Cub Cadet 2182 Bedienungsanleitung

Cub Cadet

Cub Cadet 1863 Referenzhandbuch

Cub Cadet

Cub Cadet XT2 Enduro Bedienungsanleitung

Beliebte Rasenmäher Handbücher anderer Marken

RHINO

RHINO 1958 Bedienungsanleitung

Wolf Garten

Wolf Garten Compact plus 40 B Bedienungsanleitung

Craftsman

Craftsman 917.378461 Bedienungsanleitung

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Bedienungsanleitung

Challenge

Challenge CH18V2 Betriebsanleitung

TALEN TOOLS

TALEN TOOLS AVR HGM30 Bedienungsanleitung

DEWEZE

DEWEZE ATM-725 Bedienungsanleitung

Weed Eater

Weed Eater 180083 Bedienungsanleitung

Husqvarna

Husqvarna Poulan Pro PP185A42 Bedienungsanleitung

Better Outdoor Products

Better Outdoor Products Quick Series Bedienungsanleitung

MTD

MTD 795, 792, 791, 790 Bedienungsanleitung

Toro

Toro Groundsmaster 3505-D Bedienungsanleitung

Dennis

Dennis FT 610 Bedienungsanleitung

AIRFORCE

AIRFORCE F-15 Gen 3 Bedienungsanleitung

MTD

MTD 126-220-000 Bedienungsanleitung

Toro

Toro 74806 Bedienungsanleitung

Stihl

Stihl RMA 443 PV Bedienungsanleitung

Yard-Man

Yard-Man 3700-0 Bedienungsanleitung