Cub Cadet FM48 Bedienungsanleitung

Operator's

Manual

Finishing Mower 48”, 60” & 72”

FM48

FM60

FM72

Cub Cadet Yanmar LLC.

P.O. Box 368023

Cleveland, OH 44136

PRINTED IN U.S.A.

Version 2.0

Code No.:769-03315

OPERATOR’SMANUAL

Take note! This safety alert symbol found throughout this manual is used to call

your attention to instructions involving your personal safety and the safety of

others. Failure to follow these instructions can result in injury or death.

Signal Words

Note the use of the signal words DANGER, WARNING and CAUTION with the safety

messages. The appropriate signal words for each has been selected using the following

guidelines:

DANGER: indicates an imminently hazardous situation that, if not avoided, will result in

death or serious injury.

WARNING: indicates a potentially hazardous situation that, if not avoided, could result

in death or serious injury, and includes hazards that are exposed when guards are

removed. It may also be used to alert against unsafe practices.

CAUTION: indicates a potentially hazardous situation that, if not avoided, may result in

minor or moderate injury.

This symbol means:

ATTENTION!

BECOME ALERT!

YOUR SAFETY IS INVOLVED!

8 - PARTS MANUAL

7 - PRE-DELIVERY CHECKLIST

6 - TROUBLESHOOTING

5.04 - Storage

5.03 - Suggested Spare Parts

5.02 - Blade Spindle

5.01 - Gearbox

5 - REPAIR PROCEDURES

4.07 - Transport

4.06 - Driveline

4.05 - Belt Replacement

4.04 - Belt Tension

4.03 - Blade Maintenance

4.02 - Service

4.01 - Maintenance Safety

4 - MAINTENANCE

3.10 - Removing Mower from the Tractor

3.09 - Uneven Terrain

3.08 - Operating Techniques

3.07 - Working Speed

3.06 - Start Up

3.05 - Attaching to the Tractor

3.04 - Pre-Operational Check

3.03 - Cutting Height Adjustment

3.02 - Set Up

3.01 - Operational Safety

3 - OPERATION

2.03 - Messages and Signs

2.02 - Starting and Stopping

2.01 - Preparation

2 - SAFETY PRECAUTIONS

1.03 - Assembly Instructions

1.02 - Model and Serial Number ID

1.01 - General

1 - GENERAL INFORMATION

INDEX 3CUB CADET YANMAR

1 - GENERAL INFORMATION

Thank you and congratulations for having chosen our implement.

Your new grooming mower is a technologically advanced machine constructed of high

quality sturdy components that will fulfill your working expectations.

Read this manual carefully. It will instruct you on how to operate and service your

mower safely and correctly. Failure to do so could result in personal injury and/or in

equipment damage.

1.01 - General

CAUTION: All hardware is metric. Only metric tools should be used. Other tools

that do not fit properly can slip and cause injury.

CAUTION: Right hand and left hand sides of the implement are determined by

facing in the direction the implement will travel when going forward (see fig. 4).

1.02 - Model and Serial Number ID

Attached to the frame is an ID plate showing the model and the serial number. Record

your implement model and serial number in the space provided below. Your dealer

needs this information to give you prompt, efficient service when you order parts.

FM48/FM60/FM72 OPERATOR’SMANUAL

GENERAL INFORMATION 4CUB CADET YANMAR

Model #:

Serial #:

Warranty does not cover the following:

1. Cleaning, transporting, mailing and service call charges.

2. Normal wear items such as belts, blades, bearings, drivelines, shear pins, slip

clutches, etc.

3. Depreciation or damage caused by normal wear, accidents, improper

maintenance, improper protection or improper use.

4. The use of non original spare parts and accessories.

Your Authorized Company Dealer has genuine parts in stock. Only these approved

replacement parts should be used.

This limited warranty covers defective material and workmanship. The cost of normal

maintenance or repairs for accidents or improper use and related labor will be borne by

the owner.

1.03 - Assembly Instructions

1. Unbolt the wheel arms and discard the mounting bracket.

2. Separate the wheel arms and remove the hardware bag secured between them.

3. Important: Remove the belt shields to inspect around the belt area and

under the gearbox central plate to be sure the area is clear of packing

material such as blocks of wood, paper, etc.

4. Bolt the wheel arm assemblies to the mower deck with the flat washer and lock

nuts. There is no difference between left/right or front/rear. Be sure both

assemblies are securely mounted.

5. Assemble each wheel to the yokes with one 14x140 mm. bolt and one inner

bushing. Tighten down snugly. The wheel should turn freely but have no side to

side movement.

6. Replace the belt shields.

7. Bolt up the top hitch arms to the inside of the rear support plates on the rear of

the mower (see fig. 3).

FM48/FM60/FM72 OPERATOR’SMANUAL

GENERAL INFORMATION 5CUB CADET YANMAR

Fig. 2

1. inner spacer

2. top hitch plate

3. top hitch support

4. bolt

5. top hitch arm

6. lower hitch arm

7. front support plate

8. front roller

8. Bolt up the top hitch supports to the outside of the front support plates welded to

the front of the deck (see fig. 2).

9. Bolt up the top hitch plate with the 16x150 mm. bolt. It should be bolted as

follows: bolt, top hitch support, top hitch arm, top hitch plate, spacer, top hitch

arm, top hitch support, lock nut. Tighten the lock nut down securely, the top

hitch plate should be able to swivel 360° (see fig. 2).

10.Install the lower hitch arms onto the top hitch supports. Tighten the bolts holding

the lower hitch arms. Be sure they are able to swivel (see fig. 2).

11.Grease wheel arms, and spindles. Check the gearbox for oil. It should be

approximately 1/2filled.

FM48/FM60/FM72 OPERATOR’SMANUAL

GENERAL INFORMATION 6CUB CADET YANMAR

Fig. 3

2. top hitch plate

3. top hitch support

5. top hitch arm

9. rear support plate

2 - SAFETY PRECAUTIONS

Safety is the primary concern in the design and manufacture of our products.

Unfortunately our efforts to provide safe equipment can be wiped out by a single

careless act of an operator.

In addition to the design and configuration of equipment, hazard control and accident

prevention are dependent upon the awareness, concern, prudence and proper training

of personnel involved in the operation, transport, maintenance and storage of

equipment.

It is the operator's responsibility to read and understand all safety and operating

instructions in the manual and to follow these.

Allow only properly trained personnel to operate the mower. Working with unfamiliar

equipment can lead to careless injuries. Read this manual, and the manual for your

tractor, before assembly or operating, to acquaint yourself with the machines. It is the

mower owner's responsibility, if this machine is used by any person other than yourself,

is loaned or rented, to make certain that the operator, prior to operating, reads and

understands the operator's manuals and is instructed in safe and proper use.

2.01 - Preparation

1. Before operating equipment read and understand the operator's manual and the

safety signs (see fig. 4).

2. Thoroughly inspect the implement before initial operation to assure that all

packaging materials, i.e., wires, bands, and tape have been removed.

3. Personal protection equipment including hard hat, safety glasses, safety shoes,

and gloves are recommended during assembly, installation, operation,

adjustment, maintaining and/or repairing the implement.

4. Operate the mower only with a tractor equipped with an approved

Roll-Over-Protective-System (ROPS). Always wear your seat belt. Serious injury

or even death could result from falling off the tractor.

5. Clear area to be cut of stones, branches or other debris that might be thrown,

causing injury or damage.

6. Operate only in daylight or good artificial light.

7. Ensure mower is properly mounted, adjusted and in good operating condition.

8. Ensure that all safety shielding and safety signs are properly installed and in

good condition.

SAFETY PRECAUTIONS 7CUB CADET YANMAR

FM48/FM60/FM72 OPERATOR’SMANUAL

2.02 - Starting and Stopping

1. Be sure that no one is near the machine prior to engaging or while the machine is

working.

2. Be sure the tractor is in "Neutral" before starting engine.

3. Mower operating power is supplied from tractor PTO. Refer to your tractor

manual for PTO engagement and disengagement instructions. Always operate

PTO at 540 rpm. Know how to stop the tractor and mower quickly in case of an

emergency.

4. When engaging PTO, the engine rpm should always be low. Once engaged and

ready to start cutting, raise PTO speed to 540 rpm and maintain throughout

cutting operation.

5. Check the tractor master shield over the PTO stub shaft. Make sure it is in good

condition and fastened securely to the tractor. Purchase a new shield if old shield

is damaged or missing.

6. After striking an obstacle, disengage the PTO, shut the tractor down and

thoroughly inspect for damage before restarting.

7. Never engage the PTO until the mower is in the down position and resting on the

ground. Never raise the mower until all blades have come to a complete stop.

2.03 - Messages and Signs

1. Read and adhere to all safety and operating decals on this machine (see fig. 4).

2. Before dismounting tractor: allow moving parts to stop, stop engine, set brake

and remove the key of unattended equipment.

3. Keep away from rotating blades and driveline.

4. Keep guards and shields in place and in good condition.

5. Do not mow with bystanders in area.

6. Allow no riders on tractor or mower.

7. Allow moving parts to stop before repair.

8. Securely support mower before working underneath.

Additional warning and operating decals are available at no extra charge. Please specify

model and serial number when ordering.

SAFETY PRECAUTIONS 8CUB CADET YANMAR

FM48/FM60/FM72 OPERATOR’SMANUAL

Fig. 4 - Safety Decals; Replace immediately if damaged.

SAFETY PRECAUTIONS 9CUB CADET YANMAR

FM48/FM60/FM72 OPERATOR’SMANUAL

3 - OPERATION

You have purchased a three spindle mower designed especially for the mowing of

grassy areas where a highly professional cut is required without wasting time.

This mower is perfect for the maintenance of parks, private lawns, industrial parks,

airports, hospital grounds, schools, highways, golf courses, sport complexes, etc. The

grooming mower, for tractors up to 30 HP, come in working widths of 4’, 5' and 6'. The

mower can be either tractor front or rear mounted and is available in rear discharge. On

your mower, the tractor PTO transmits its power through a driveline to a speed multiplier

gearbox. A pulley is attached to the pinion gear shaft of the gearbox which, via high

resistance belts, transmits power to pulleys coupled to the three individual spindle

shafts. Blades are secured to these shafts which turn at a high blade tip speed to cut

the grass.

Our grooming mower comes equipped with 4 swivel wheels. Aside from regulating the

cutting height, the wheels are set in such a way as to allow the mower to follow the

contour of the terrain and give a precise level cut even in undulating conditions.

3.01 - Operational Safety

CAUTION: Our mowers are designed considering safety as the most important

aspect and are the safest available in today's market. Unfortunately, human

carelessness can override the safety features built into our machines. Injury

prevention and work safety, aside from the features on our mowers, is very much

due to the responsible use of the equipment. It must always be operated

prudently following with great care, the safety instructions laid out in this manual.

1. The use of this equipment is subject to certain hazards which cannot be

prevented by mechanical means or product design. All operators of this

equipment must read and understand this entire manual, paying particular

attention to safety and operating instructions, prior to using.

2. Do not operate the tractor and mower when you are tired, sick or when using

medication.

3. Keep all helpers and bystanders at least several feet from a rotary mower. Only

properly trained people should operate this machine.

4. The majority of accidents involve entanglements on the driveline, injury of

bystanders by objects thrown by the rotating blades, and operators being

knocked off the tractor by low hanging limbs and then being run over by the

mower. Accidents are most likely to occur with machines that are loaned or

FM48/FM60/FM72 OPERATOR’SMANUAL

OPERATION 10 CUB CADET YANMAR

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cub Cadet Rasenmäher Handbücher

Cub Cadet

Cub Cadet 364 Bedienungsanleitung

Cub Cadet

Cub Cadet 13AF91AP010 Bedienungsanleitung

Cub Cadet

Cub Cadet 1863 Bedienungsanleitung

Cub Cadet

Cub Cadet 29HP Tank 53AJ8CTX750 Betriebsanleitung

Cub Cadet

Cub Cadet 23HP Z-Force 48 w/ Fabricated Deck Betriebsanleitung

Cub Cadet

Cub Cadet 1527 Bedienungsanleitung

Cub Cadet

Cub Cadet Rzt 46 Bedienungsanleitung

Cub Cadet

Cub Cadet 19A30003100 Bedienungsanleitung

Cub Cadet

Cub Cadet RZT 50 Bedienungsanleitung

Cub Cadet

Cub Cadet RZT 42 w/42" Mower Deck Bedienungsanleitung

Cub Cadet

Cub Cadet 182 Bedienungsanleitung

Cub Cadet

Cub Cadet 1863 Referenzhandbuch

Cub Cadet

Cub Cadet 1806 Bedienungsanleitung

Cub Cadet

Cub Cadet 997 Bedienungsanleitung

Cub Cadet

Cub Cadet 1000 Series Bedienungsanleitung

Cub Cadet

Cub Cadet LTX1050/KW Bedienungsanleitung

Cub Cadet

Cub Cadet GT 2544 Bedienungsanleitung

Cub Cadet

Cub Cadet Ultima ZTX6 60 Bedienungsanleitung

Cub Cadet

Cub Cadet 13WQ91AP009 Bedienungsanleitung

Cub Cadet

Cub Cadet GT 3204 Bedienungsanleitung

Cub Cadet

Cub Cadet LT1042 Bedienungsanleitung

Cub Cadet

Cub Cadet GT 2542 Bedienungsanleitung

Cub Cadet

Cub Cadet Time Saver Bedienungsanleitung

Cub Cadet

Cub Cadet XT3 enduro series Bedienungsanleitung

Beliebte Rasenmäher Handbücher anderer Marken

RHINO

RHINO 1958 Bedienungsanleitung

Wolf Garten

Wolf Garten Compact plus 40 B Bedienungsanleitung

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Bedienungsanleitung

Challenge

Challenge CH18V2 Betriebsanleitung

TALEN TOOLS

TALEN TOOLS AVR HGM30 Bedienungsanleitung

DEWEZE

DEWEZE ATM-725 Bedienungsanleitung

Weed Eater

Weed Eater 180083 Bedienungsanleitung

Husqvarna

Husqvarna Poulan Pro PP185A42 Bedienungsanleitung

Better Outdoor Products

Better Outdoor Products Quick Series Bedienungsanleitung

MTD

MTD 795, 792, 791, 790 Bedienungsanleitung

Toro

Toro Groundsmaster 3505-D Bedienungsanleitung

Dennis

Dennis FT 610 Bedienungsanleitung

MTD

MTD 126-220-000 Bedienungsanleitung

Toro

Toro 74806 Bedienungsanleitung

Stihl

Stihl RMA 443 PV Bedienungsanleitung

Yard-Man

Yard-Man 3700-0 Bedienungsanleitung

AIRFORCE

AIRFORCE F-15 Gen 3 Bedienungsanleitung

MTD

MTD 050 thru 062 Bedienungsanleitung