Cub Cadet ZT1 42E Gebrauchs- und Pflegehandbuch

Instruction Sheet 1 of 8

The VCM buttons are shown in Figure1.

Calibration Of The Ultima ZT1 42E

ECO

PTO

HEADLIGHT

LOW SPEED

PRECISION

DRIVE

START

FIGURE 1

KEY SLOT

Throttle Position Sensor (TPS)

INSTRUCTION SHEET

769-26105/01

DRM

Vehicle Control Module (VCM) Buttons: Page 1.

Pre Calibration Steps: Page 2.

Calibration Steps: Pages 3 through 8.

INDEX:

VCM

NOTE: Videos are available for the Operation and Calibration of the Ultima ZT1 42E by clicking on one of the

How to Operate the Ultima ZT1 42E: https://youtu.be/NV9wlv-cf5k

How to Calibrate the Ultima ZT1 42E Throttle Position Sensor: https://youtu.be/IUNXIiuQQGw

links below.

05.13.21

FIGURE 3

4. Confirm that the lap bars are aligned evenly across from each other by adjusting the adjust knobs shown in Figure 3.

Adjust Knob

Instruction Sheet 2 of 8

INSTRUCTION SHEET

5. In a large area free of bystanders and obstacles, drive the mower in both “Low Speed Precision Drive” and

“Standard Drive” modes. Operate the mower through turns, starts and stops, etc. If the experience is unsatisfactory in

the operation of the mower, proceed to the “Calibration Steps” on Page 3.

DRM

FIGURE 2

Rivnut

Adjustment

Bolt

1. Park the mower on a flat level surface. Chock the rear wheels.

2. Equal air pressure and tire size is important on zero turn mowers and is especially important on the electrically

powered drive motors of the ZT1 42E. Check and maintain both rear tires at 10 psi and the front tires at 20 psi.

3. Confirm that both lap bar drive control lever stop adjustment bolts are adjusted all the way out so that the bolt is flush

with the end of the Rivnut. See Figure 2.

Pre Calibration Steps:

769-26105/01

FIGURE 2

3. Simultaneously press and hold the ECO

the HEADLIGHT

until the screen displays FNRas shown in Figure 2,

then release the ECO and HEADLIGHT

NOTE: If the VCM will not accept calibration inputs,

retry Steps 1 through 3. If the VCM still will not

accept calibration inputs, contact your local

Cub Cadet Service Dealer.

and

buttons for 7 seconds or

buttons.

Instruction Sheet 3 of 8 DRM

INSTRUCTION SHEET

4. Leave the right lap bar in the “OUTWARD”

position and move the left lap bar to the inward

“NEUTRAL” position as shown in Figure 3.

Right Lap Bar “OUTWARD” Position

Left Lap Bar Inward

“NEUTRAL” Position

FIGURE 3

1. Insert the key into key slot.

2. Make sure both lap bars are in the “OUTWARD”

position as shown in Figure 1.

Calibration Steps:

FIGURE 1

Lap Bars In The

“OUTWARD”

Position

IMPORTANT: The Brake must be released. DO NOT touch the brake pedal during any of the calibration procedures.

NOTE: If during the calibration procedures, an error code shows up on the screen. Start the calibration

procedures over beginning at Step 1 after removing the key.

769-26105/01

5. Move the left lap bar forward until it hits a hard stop

on the lap bar drive control lever stop adjustment bolt

6. Press the LOW SPEED PRECISION DRIVE

button.

7. Release the lap bar and allow it to return to the

8. The “F” on the screen should have a box around it as

shown in Figure 5.

FIGURE 4

FIGURE 5

Rivnut as shown in Figure 4.

“NEUTRAL” position.

INSTRUCTION SHEET

Instruction Sheet 4 of 8 DRM

769-26105/01

Instruction Sheet 5 of 8

INSTRUCTION SHEET

DRM

button.

10. The “N” on the screen should have a box around it

as shown in Figure 7.

FIGURE 6

FIGURE 7

9. Place the left lap bar in the “OUTWARD”

START

position as shown in Figure 6 and press the

769-26105/01

Instruction Sheet 6 of 8

INSTRUCTION SHEET

DRM

12. The FNRdisplay will disappear and the screen will

switch to the start screen as shown in Figure 9. This

indicates that the calibration for the left lap bar

13. Release the lap bar and allow it to return

FIGURE 8

FIGURE 9

11. Move the left lap bar to the “NEUTRAL”

PTO button.

NOTE: If you hold the button for more than

7 seconds, you will get an error code.

position and pull rearward until it hits a

hard stop as shown in Figure 8 and press the

to the “NEUTRAL” position.

has been completed and saved.

769-26105/01

Instruction Sheet 7 of 8

INSTRUCTION SHEET

DRM

16. Simultaneously press and hold the PTO

the HEADLIGHT buttons for 7 seconds or

and HEADLIGHT

14. For the right side lap bar calibration, proceed as follows.

15. Place both lap bars in the “OUTWARD” position as

FIGURE 11

and

until the screen displays FNRas shown in Figure 11,

then release the PTO

buttons.

FIGURE 10

Lap Bars In The

“OUTWARD”

Position

shown in Figure 10.

769-26105/01

INSTRUCTION SHEET

Instruction Sheet 8 of 8 DRM

If you feel that there is no difference, please contact us directly. We would like to speak to you about your feedback and

points of concern. Please send an email to ElectricRidingMowers@mtdproducts.com so that we can coordinate a time

to discuss this at your convenience.

17. Leave the left lap bar in the “OUTWARD”

position and move the right lap bar to the inward

“NEUTRAL” position as shown in Figure 12.

FIGURE 12

Left Lap Bar

Right Lap Bar Inward

“NEUTRAL” Position

“OUTWARD”

Position

18. For the completion of the right lap bar calibration,

repeat Steps 5 through 13, then proceed to

Step 19.

19. After performing the calibration procedures for both

lap bars, test drive the mower again in a large area

in both drive modes to verify that the recalibration

is satisfactory.

769-26105/01

Inhaltsverzeichnis

Andere Cub Cadet Rasenmäher Handbücher

Cub Cadet

Cub Cadet LTX1042KW Bedienungsanleitung

Cub Cadet

Cub Cadet LT1050 Bedienungsanleitung

Cub Cadet

Cub Cadet CC 500 EL Bedienungsanleitung

Cub Cadet

Cub Cadet GT1554 Bedienungsanleitung

Cub Cadet

Cub Cadet CS 552 Bedienungsanleitung

Cub Cadet

Cub Cadet RZT-S Bedienungsanleitung

Cub Cadet

Cub Cadet Z-Force 44 Bedienungsanleitung

Cub Cadet

Cub Cadet RZT 42 Bedienungsanleitung

Cub Cadet

Cub Cadet LTI050 Bedienungsanleitung

Cub Cadet

Cub Cadet LT1024 Bedienungsanleitung

Cub Cadet

Cub Cadet 949 Bedienungsanleitung

Cub Cadet

Cub Cadet 979 Bedienungsanleitung

Cub Cadet

Cub Cadet GSS-1291 Bedienungsanleitung

Cub Cadet

Cub Cadet 2165 Bedienungsanleitung

Cub Cadet

Cub Cadet Fabricated Deck InDirect Injection Diesel Betriebsanleitung

Cub Cadet

Cub Cadet 148 Bedienungsanleitung

Cub Cadet

Cub Cadet 53AH8CTX750 Einrichtungshandbuch

Cub Cadet

Cub Cadet 38" Bedienungsanleitung

Cub Cadet

Cub Cadet LTX 1045 Bedienungsanleitung

Cub Cadet

Cub Cadet RZT 50 (w/50" Mower Deck) Bedienungsanleitung

Cub Cadet

Cub Cadet 387 Bedienungsanleitung

Cub Cadet

Cub Cadet 19A70040100 Bedienungsanleitung

Cub Cadet

Cub Cadet i1050 Bedienungsanleitung

Cub Cadet

Cub Cadet LTX 1040 Bedienungsanleitung

Beliebte Rasenmäher Handbücher anderer Marken

RHINO

RHINO 1958 Bedienungsanleitung

Wolf Garten

Wolf Garten Compact plus 40 B Bedienungsanleitung

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Bedienungsanleitung

Challenge

Challenge CH18V2 Betriebsanleitung

TALEN TOOLS

TALEN TOOLS AVR HGM30 Bedienungsanleitung

DEWEZE

DEWEZE ATM-725 Bedienungsanleitung

Weed Eater

Weed Eater 180083 Bedienungsanleitung

Husqvarna

Husqvarna Poulan Pro PP185A42 Bedienungsanleitung

Better Outdoor Products

Better Outdoor Products Quick Series Bedienungsanleitung

MTD

MTD 795, 792, 791, 790 Bedienungsanleitung

Toro

Toro Groundsmaster 3505-D Bedienungsanleitung

Dennis

Dennis FT 610 Bedienungsanleitung

MTD

MTD 126-220-000 Bedienungsanleitung

Toro

Toro 74806 Bedienungsanleitung

Stihl

Stihl RMA 443 PV Bedienungsanleitung

Yard-Man

Yard-Man 3700-0 Bedienungsanleitung

AIRFORCE

AIRFORCE F-15 Gen 3 Bedienungsanleitung

MTD

MTD 050 thru 062 Bedienungsanleitung