Culligan SILVER SERIES Bedienungsanleitung

CULLIGAN

SILVER SERIES™

AUTOMATIC

WATER CONDITIONER

MODELS FROM 2001

Cat. No. 01882319

Rev.C12/16/02

DCO#4930

Installation

and

Operating

Instructions

Printed in USA

WARNING- Prior to servicing equipment,disconnectpower

supply to prevent electrical shock.

Attention Culligan Customer:

Theinstallation, service andmaintenance of thisequipment should

berenderedby a qualifiedandtrainedservice technician.Yourlocal

independentlyoperatedCulligandealeremploystrainedserviceand

maintenance personnel who are experienced in the installation,

functionandrepair of Culligan equipment.Thispublicationis written

specificallyfor theseindividuals and isintended for theiruse.

Weencourage Culliganusers to learnabout Culliganproducts, but

we believe that product knowledge is best obtained by consulting

withyourCulligandealer.Untrained individuals whouse thismanual

assumetheriskof any resultingpropertydamageorpersonal injury.

WARNING - If incorrectly installed, operated or maintained,

this product can cause severe injury. Those who install,

operate, or maintain this product should be trained in its

proper use, warned of its dangers, and should read the

entire manual before attempting to install, operate or

maintain this product.

THIS SYSTEM IS NOT INTENDED TO BE USED FOR TREATING

WATER THAT IS MICROBIOLOGICALLY UNSAFE OR OF

UNKNOWN QUALITY WITHOUT ADEQUATE DISINFECTION

BEFORE OR AFTER THE SYSTEM.

CULLIGANINTERNATIONALCOMPANY

OneCulliganParkway

Northbrook,Illinois60062-6209

847.205.6000

Table of Contents Page

Introduction ............................................................... 2

Specifications............................................................ 3

Preparation ............................................................... 4

Installation................................................................. 6

Settings ...................................................................12

Programming............................................................15

ManualCycling ........................................................19

ServiceCheck ..........................................................20

Operation .................................................................21

SanitizingInstructions ..............................................22

Parts List .................................................................23

CULLIGAN

SILVER SERIES™

AUTOMATIC

WATER CONDITIONER

MODELS FROM 2001

Installation

and

Operating

Instructions

The Culligan Silver Series™Water Softeners are tested and validated by WQA

andcertified byULagainstANSI/NSFStandard 44 for the effectivereduction of

calcium and magnesium (hardness) as well as Barium and Radium 226/228*.

For installations in Massachusetts, the Commonwealth of Massachusetts

PlumbingCode248CMRshallbeadheredto.Consultyourlicensedplumber

for installation of the system. This system and its installation must comply

withstateand localregulations.

SAFE PRACTICES

Throughout this manual there are paragraphs set off by special headings.

NOTICE: Notice is used to emphasize installation, operation or maintenance information which is important, but

does not present any hazard.

Example: NOTICE: The nipple must extend no more than 1 inch above the cover plate.

CAUTION:Caution is used when failure to follow directions could result in damage to equipment or property.

Example:

CAUTION:Disassembly while under water pressure can result in flooding.

WARNING:Warning is used to indicate a hazard which could cause injury or death if ignored. Example:

WARNING! ELECTRICALSHOCKHAZARD! UNPLUG THE UNITBEFORE

REMOVINGTHE COVER ORACCESSINGANYINTERNALCONTROLPARTS.

SERIAL NUMBERS

The control valve serial number is located on the back of the timer case.

The media tank serial number is located on the top surface of the tank.

NOTICE: Do not remove or destroy the serial number. It must be referenced on request for warranty repair or

replacement.

This publication is based on information available when approved for printing. Continuing design refinement could

cause changes that may not be included in this publication.

*Verified utilizing hardness surrogate per ANSI/NSF Standard 44.

Introduction

2CULLIGANSILVERSERIES WATERSOFTENER

ANSI/NSF44

WaterSoftener

81WN

Specifications

Culligan Silver Series™Water Conditioners with Time Clock, Aqua-Sensor®Device or Soft-Minder®Meter

9” Model 12” Model

Control Valve 5-cycle, Reinforced Thermoplastic 5-cycle, Reinforced Thermoplastic

Overall Conditioner Height 51 in 51 in

1 295 mm 1 295 mm

Media Tank Dimensions (Dia x Ht) 9 x 45 in 12 x 45 in

229 x 1 143 mm 305 x 1 143 mm

Salt Storage Tank Dimensions (Dia x Ht) 16 x 43 in 18 x 43 in

406 x 1 092 mm 457 x 1 092 mm

18 x 43 in

457 x 1092 mm

Exchange Media, Type and Quantity Cullex®Media, 0.86 ft3Cullex®Media, 1.4 ft3

Cullex®Media, 24.5 L Cullex®Media, 40 L

Underbedding, Type and Quantity Cullsan®Underbedding, 12 lb Cullsan®Underbedding, 30 lb

Cullsan®Underbedding, 5.4 kg Cullsan®Underbedding, 14 kg

Exchange Capacity 17,500 gr @ 4.0 lb 24,100 gr @ 6.0 lb

@ Salt Dosage Per Recharge11 133 g @ 1.8 kg 1 560 g @ 2.7 kg

23,900 gr @ 8.0 lb 34,500 gr @ 12.0 lb

1 547 g @ 3.6 kg 2 234 g @ 5.4 kg

26,600 gr @ 12.0 lb 41,900 gr @ 18.0 lb

1 722 g @ 5.4 kg 2 713 g @ 8.1 kg

Efficiency rated dosage14 380 gr/lb 4 010 gr/lb

626 g/kg 573 g/kg

Freeboard to Media216.6-17.6 in 17.5-18.5 in

420-447 mm 444-470 mm

Freeboard to Underbedding339.2 in 38.5 in

996 mm 978 mm

Salt Storage Capacity 250 lb or 375 lb 375 lb

114 kg or 170 kg 170 kg

Rated Service Flow @ Pressure Drop 7.5 gpm @ 15 psi 7.5 gpm @ 13 psi

30 Lpm @ 102 kPa 28 Lpm @ 90 kPa

Total Hardness, Maximum 75 gpg 99 gpg

1 283 mg/L 1 692 mg/L

Total Iron, Maximum 5 ppm 5 ppm

5 mg/L 5 mg/L

Hardness to Iron Ratio, Minimum 8 gpg to 1 ppm 8 gpg to 1 ppm

140 mg/L to 1 mg/L 140 mg/L to 1 mg/L

Operating Pressure 20-125 psi 20-125 psi

140-860 kPa 140-860 kPa

Operating Temperature 33-120°F 33-120°F

1-50°C 1-50°C

Electrical Requirements 24V/60Hz 24V/60 Hz

Electrical Power Consumption, Min/Max 3 Watts/35 Watts 3 Watts/35 Watts

Drain Flow, Maximum42.3 gpm 3.5 gpm

9 Lpm 14 Lpm

Recharge Time, Average580 min 85 min

Recharge Water Consumption, Average 40 gal 82 gal

170 L 325 L

1 The efficiency rated dosage is only valid at the 4 lb. salt dosage for the 9" models and 6 lb. for the 12" models.

2 Measured from top of media to top surface of tank threads (backwashed and drained).

3 Measured from top of underbedding to top surface of tank threads.

4 Backwash at 120 psi (830 kPa).

5 10 minute backwash, 4 lb (1.8 kg) 9” model or 6 lb (2.7 kg) 12” model salt dosage. SPECIFICATIONS 3

COMPONENTDESCRIPTION

The water conditioner is shipped from the factory in a minimum of four cartons. Remove all components from their

cartons and inspect them before starting installation.

ControlValveAssembly - Includesthe 5-cycleregeneration control valve and theAccusoft®Microprocessor. Small

parts packages will contain additional installation hardware. Installation and Operations Instructions and an

Owner’s Guide are included.

MediaTank- Includes Tripl-Hull™media tank complete with Cullex®ion exchange resin, underbedding and outlet

manifold.

Salt StorageTankAssembly - Includes salt storage container with support plate and Dubl-Safe™brine refill valve

and chamber.

Bypass Valve - Includes the Cul-Flo-Valv®, interconnecting couplings, and the screws necessary for assembly.

TOOLS AND MATERIALS

The following tools and supplies will be needed, depending on installation method. Observeall applicable codes.

AllInstallations

• Safety glasses

• Phillipsscrewdrivers, smalland mediumtip.

• Gaugeassembly (PN 00-3044-50 or equivalent)

• Siliconelubricant(PN 00-4715-07 orequivalent)-DONOTUSEPETROLEUM-BASEDLUBRICANTS

• A bucket, preferably light-colored

• Towels

SpecialTools

• Torch, solder and flux for sweat copper connections

• Threading tools, pipe wrenches and thread sealer for threaded connections.

• Saw, solvent and cement for plastic pipe connections.

Materials

• Brineline,5/16” (PN 00-3031-28 orequivalent)

• Drainline,1/2”(PN 00-3030-82, gray,semi-flexible;orPN 00-3319-46, black, semi-rigid;orequivalent)

• Thread sealing tape

• Pressure reducing valve (if pressure exceeds 125 psi [860 kPa], PN 00-4909-00 or equivalent)

• Pipe and fittings suited to the type of installation

• Water softener salt (rock, solar or pellet salt formulated specifically for water softeners)

APPLICATION

Waterquality - Verify that raw water hardness and iron are within limits. Note the hardness for setting the salt

dosage and recharge frequency.

Pressure - If pressure exceeds 125 psi (860 kPa), install a pressure reducing valve (see materials checklist). On

private water systems, make sure the minimum pressure (the pressure at which the pump starts) is greater than 20

psi (140 kPa).Adjust the pressure switch if necessary.

CAUTION: The use of a pressure reducing valve may limit the flow of water in the

household.

Preparation

4CULLIGANSILVERSERIES™WATERSOFTENER

PREPARATION 5

Temperature- Do not install the unit where it might freeze, or next to a water heater or furnace or in direct sunlight.

LOCATION

Space requirements - Allow 6-12 inches (15-30 cm) behind the unit for plumbing and drain lines and 4 feet (1.3

meters) above for service access and filling the salt container.

Floor surface - Choose an area with solid, level floor free of bumps or irregularities. Bumps, cracks, stones and

otherirregularitiescan causethe saltstorage tankbottomto crackwhen filledwith saltand water.

Drain facilities - Choose a nearby drain that can handle the rated drain flow (floor drain, sink or stand pipe). Refer

tothe Drain Line Chart,Table1 (page 10), formaximum drainline length.

NOTICE: Most codes require an anti-siphon device or airgap. Observe all local plumbing codes and drain

restrictions. The system and installation must comply with all state and local laws and regulations.

Electricalfacilities -A10-foot cord and wall mount plug-in transformer are provided. The customer should provide

a receptacle, preferably one not controlled by a switch that can be turned off accidentally. Observe local electrical

codes.

6CULLIGANSILVERSERIES™WATERSOFTENER

PLACEMENT

Refer to Figure 1 for system placement.

• Set the media tank on a solid, level surface near water, drain and electrical facilities. Place the outlet (black

coupling) of the tank on the left.

• Set the brine system on a flat, smooth, solid surface as near the media tank as possible.

MOUNT THE CONTROL VALVE

See Figure 2 for a visual on mounting the control valve to the tank.

• Remove and discard the protective covers on the tank couplings.

• Lubricate the o-rings on the tank couplings with silicone lubricant.

• Place the control on the tank couplings and press down firmly.

NOTICE: The white tank coupling is the inlet, and should be located on the inlet side (right side) of the control.

• Install the u-clamps on both sides of the control and secure with the screws.

TWELVE INCH SOFTENERS

As shipped from the factory, each control is equipped as a 9-inch unit. A12-inch eductor nozzle and backwash flow

control are included with each unit for conversion for use with the 12-inch tanks.

NOTICE: To prevent injury, convert unit to a twelve-inch configuration prior to installation.

Refer to Figure 3 for a visual on changing the eductor nozzle and the backwash flow control.

Eductor Nozzle Replacement:

• Remove the three screws on the eductor cap and remove the cap.

• Remove the eductor assembly.

• Remove the eductor screen from the assembly

• Remove the blue nozzle and replace it with the beige nozzle. Make sure to put the o-ring on the beige nozzle.

• Reverse the procedure to reassemble. To prevent leaks, ensure that the gasket is in the proper position.

Backwash Flow Control Replacement:

• Remove the drain clip and pull the drain elbow straight off.

• Remove the backwash flow control located behind the elbow. Put the #3 restrictor in its place.

NOTICE: The number on the flow control should face into the valve body.

• Reverse the procedure to reassemble.

Installation

FIG. 1

INSTALLATION 7

FIG. 2

FIG. 3

PLUMBINGCONNECTIONS

Two methods of connecting the water softener to the plumbing system are available. Shipped with each softener is

a Culligan®Cul-Flo-Valv®bypass valve, either PN 01-0124-88 or 01-0102-38, which is used to connect the softener

to the plumbing system. The bypass allows the softener to be isolated from the water service line if service is

necessary while still providing water to the house. If local conditions warrant, you may use the sweat adaptor kits,

PN00-3314-44or00-3314-45.

NOTICE: The Soft-Minder®meter cannot be used with the sweat adaptors.

CAUTION:Close the inlet supply line and relieve system pressure before

cutting into the plumbing! Flooding could result!

CAUTION: When making sweat connections, remove all plastic and rubber

components which contact brass or copper. Damage to these components may

resultotherwise.

BYPASS VALVE INSTALLATION

AQUA-SENSOR®SENSING DEVICEAND TIME CLOCK UNITS ONLY

The bypass valve connects directly to the backplate of the valve with a pair of couplings and screws (Figure 4). To

facilitate this connection, remove the plate by pulling up on the u-clip on the back of the valve. Lubricate all o-rings

with silicone lubricant.

BYPASS VALVE INSTALLATION

SOFT-MINDER®METER ONLY

The Soft-Minder meter is placed between the bypass valve and the control in place of the couplings shipped with

the Cul-Flo-Valv®(Figure 5). Make sure the meter is on the outlet port of the control and that it is installed with the

arrow pointing in the direction of water flow. A pair of elongated bolts are packaged with the meter to hold the

bypass valve to the back plate of the control. Lubricate all o-rings with silicone lubricant.

SWEATADAPTOR INSTALLATION

The sweat adaptors use a snap ring to hold them to the backplate of the control valve. The back plate will need to

be removed from the valve for this connection. A pair of snap ring pliers, PN 00-5916-09, are needed for this

connection.

CAUTION: When reinstalling back plate to control valve, make sure the u-clip

fully engages the two bottom holes of the bracket (Figure 6). Secure bracket from

the top with the two mounting screws provided.

8CULLIGANSILVERSERIES™WATERSOFTENER

FIG. 4 FIG. 5

FIG. 6

FIG. 7

CONNECTTHEBRINELINE

Refer to Figures 6 & 7.

• Use the length of brine line included in the brine tank, or measure a length of brine line sufficient to reach from the

brine tank to the brine fitting, with no sharp bends. For easier access to the float it is recommended to add an extra

four feet (1.3 meters) of length to the brine line. Cut both ends of the brine line squarely and cleanly.

• Remove the brine valve from the brine tank and then remove the white nut and insert from the float rod. Return

float rod to its original position.

• Slip the white nut over one end of the tubing and press the plastic insert into the end of the tubing (Figure 7).

Connect to the brine valve and tighten nut.

• Remove white nut from the brine connection, and remove the plastic insert from the brine connection fitting.

• Slip the white nut over one end of the tubing and press the plastic insert into the end of the tubing (Figure 7).

Connect to the brine connection on the valve and tighten nut (Figure 6).

DRAINLINE CONNECTION

Refer to Table 1, page 10 under the applicable tank size for drain line length and height limitations, and to Figure 3.

• Remove 1/2” pipe clamp from the small parts pack included with the control.

• Route a length of 1/2” drain line from the drain elbow to the drain.

• Fasten the drain line to the elbow with the clamp.

• Secure the drain line to prevent its movement during regeneration. When discharging into a sink, or open floor

drain, a loop in the end of the tube will keep it filled with water and will reduce splashing at the beginning of each

regeneration.

Andere Handbücher für SILVER SERIES

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Culligan Wasserfiltersystem Handbücher

Culligan

Culligan RV-EZ Bedienungsanleitung

Culligan

Culligan Aqua-Cleer H-82 WT Bedienungsanleitung

Culligan

Culligan FM 15 Bedienungsanleitung

Culligan

Culligan FM-5 Bedienungsanleitung

Culligan

Culligan WSH-C125 Bedienungsanleitung

Culligan

Culligan Sulfur-Cleer Fiberglass Bedienungsanleitung

Culligan

Culligan SY-2650 Beilage

Culligan

Culligan ClearLink Pro Bedienungsanleitung

Culligan

Culligan Gold Arsenic Series Bedienungsanleitung

Culligan

Culligan WH-S100-O Bedienungsanleitung

Culligan

Culligan 9" Bedienungsanleitung

Culligan

Culligan Iron-Cleer Plus Bedienungsanleitung

Culligan

Culligan G1 Series Handbuch

Culligan

Culligan 01036140 Bedienungsanleitung

Culligan

Culligan HD-950A Bedienungsanleitung

Culligan

Culligan HF-360 Bedienungsanleitung

Culligan

Culligan Drinking Water System Bedienungsanleitung

Culligan

Culligan Aquasential Tankless RO Bedienungsanleitung

Culligan

Culligan HF-160 Bedienungsanleitung

Culligan

Culligan Aqua-Cleer Bedienungsanleitung

Culligan

Culligan US-EZ Bedienungsanleitung

Culligan

Culligan HF-150A Bedienungsanleitung

Culligan

Culligan FM-15A Bedienungsanleitung

Culligan

Culligan Aquasential Select Plus Series Bedienungsanleitung

Beliebte Wasserfiltersystem Handbücher anderer Marken

Wisy

Wisy LineAir 100 Bedienungsanleitung

Schaffner

Schaffner Ecosine FN3446 Series Betriebsanleitung

Pentair

Pentair FLECK 4600 SXT Benutzerhandbuch

H2O International

H2O International H20-500 Bedienungsanleitung

Renkforce

Renkforce 2306241 Bedienungsanleitung

Neo-Pure

Neo-Pure TL3-A502 Bedienungsanleitung

FLTR

FLTR OBF Bedienungsanleitung

STA-RITE

STA-RITE VERTICAL GRID DE FILTERS S7D75 Bedienungsanleitung

Applied Membranes

Applied Membranes W-G844EM Bedienungsanleitung

BEGA

BEGA 116 Bedienungsanleitung

WATA

WATA Standard Bedienungsanleitung

Price

Price FFU series Handbuch

Gaggenau

Gaggenau BRITA INTENZA 467873 Bedienungsanleitung

Brita

Brita SAFF-100 Bedienungsanleitung

HEISSNER

HEISSNER FPU24000-00 Bedienungsanleitung

BGS technic

BGS technic 1518 Bedienungsanleitung

Reverse Osmosis

Reverse Osmosis RF Series Bedienungsanleitung

ubbink

ubbink Filtramax Series Bedienungsanleitung