Curtis RCD672 Bedienungsanleitung

PORTABLE CD PLAYER WITH RADIO

MODEL NO. RCD672

OWNER'S MANUAL

PLEASE READ BEFORE OPERATING THIS EQUIPEMNT

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR BACK). NO

USER-SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

DANGEROUS VOLTAGE

The lightning ﬂash with arrowhead symbol,

within an equilateral triangle is intended to alert

the user to the presence of uninsulated

dangerous voltage within the product’s

enclosure that may be of sufficient magnitude to

constitute a risk of electric shock to persons.

ATTENTION

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

DANGER:

Invisible and hazardous laser radiation

when open and interlock failed or defeated.

Avoid direct exposure to beam.

LASER SAFETY: This unit employs a laser. Only qualified service

personnel should attempt to service this device due to possible injury.

CAUTION: USE OF CONTROLS, ADJUSTMENTS OR PERFORMANCE

HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

PREPARATION FOR USE

Unpacking and Setup

•

Power Sources

This portable audio system is designed to operate on AC 120V~60Hz or by

using eight (8) "C" batteries, (batteries not included). Attempting to operate this

unit from any other power source may cause damage to the unit, which is not

covered by your warranty.

AC Operation

Unwind the AC cord and extend it to its full length. Insert the small end of the

AC cord into the AC power socket on the rear of the unit. Insert the other end of

the AC cord into any convenient AC 120V~60Hz household outlet.

Battery Installation

To use this unit with battery power, remove the battery compartment on the

bottom of the unit by sliding it towards the rear of the unit and lifting the battery

door off. Insert eight (8) "C" size batteries (batteries not included) following the

diagram in the compartment.

NOTE: The power cord must be disconnected from the AC power socket on the

rear of the unit in order for the unit to operate on battery power.

Carefully remove the unit from the display carton and remove all packing

material from the unit itself.

The detachable AC power cord is packed in the carton separately from the

unit. Make sure the AC power cord is not accidentally discarded with the

carton or packing material.

Press the CD Door OPEN/CLOSE area to open the CD compartment door.

There is a white card in the CD compartment which intended to prevent the

CD pickup from moving during shipment of the product. Remove this card

from the CD compartment before use.

LOCATION OF CONTROLS

1. VOLUME CONTROL

2.  ALBUM BUTTON

3.  STOP BUTTON

4.  SKIP / TUNER DOWN BUTTON

5.  MEMORY / CLOCK SET BUTTON

6.  FM ROD ANTENNA

7.  POWER BUTTON

8.  FUNCTION BUTTON

9.  PLAY / PAUSE / MEMORY UP

 BUTTON

10.  SKIP / TUNER UP BUTTON

11.  P-MODE / MEMORY DOWN BUTTON

12.  DISPLAY WITH BACK LIGHT

13.  SPEAKER

14.  CARRYING HANDLE

15.  CD DOOR OPEN / CLOSE

16.  CD COMPARTMENT

17.  BATTERY COMPARTMENT

 (BOTTOM OF UNIT)

18.  AC POWER SOCKET

 (REAR OF UNIT)

19.  PHONE JACK (SIDE OF UNIT)

20.  BASS BOOST BUTTON

21. BAND BUTTON

13 13

819

921 1817

4 10

OPERATING INSTRUCTIONS

SETTING THE CLOCK

LINE IN Jack (FRONT OF UNIT)

By using a home audio connection cable (not included), you can listen to an

external audio unit through this unit's speakers. Before making any

connections, turn off the power to all equipment.

Plug a connection cable (not included) between the LINE OUT jack on the

external audio unit and this unit's LINE IN jack. (Do not connect it to this unit's

PHONES jack.)

With the power off, press and hold the MEMORY/CLOCK button;"12H" will

blink.

Press the REW SKIP TUNER-DN or FEW. SKIP/TUNER-UP button to set the

unit to the 24 hour (24H) mode (also known as military time), or 12 hour

(12H) mode.

Press the MEMORY/CLOCK SET button and the hours will blink.

Press the REW SKIP TUNER-DN or FEW. SKIP/TUNER-UP button to set the

current hour, then press the MEMORY/CLOCK SET button again; the minute

digits will blink.

Press the REW SKIP TUNER-DN or FEW. SKIP/TUNER-UP button to set the

current minute, then press the MEMORY/CLOCK SET.

OPERATING INSTRUCTIONS

PLAYING COMPACT DISCS

NOTES:

CD PAUSE CONTROL

Press the POWER button to turn the unit on.

Open the CD compartment lid by pressing the CD Door OPEN/CLOSE area.

Insert a disc, label side up, into the compartment. Press the CD Door

OPEN/CLOSE area to close the CD compartment lid; the total tracks will

appear in the display.

Press the PLAY/PAUSE button to begin playback; the current track will

appear in the display.

When the disc is through playing, it will stop. Press the STOP button to stop

the disc before it is finished.

Press the POWER button to turn the CD off.

If a disc is inserted incorrectly, dirty, damaged or not present at all, "no" will

appear in the display.

As each track is playback, the track number is shown in the display

To prevent damage to the disc, never open the CD door while the disc is

rotating. Wait for the disc to stop before opening the CD door. Never touch

the lens when the CD compartment door is open.

DO NOT use the carrying handle when playing a CD. The CD should only be

used on a steady surface.

This unit will play 3" CD singles, no adapter is needed.

The maximum playing time is 74 minutes.

During CD playback, if you wish to pause the disc momentarily, press the

PLAY/PAUSE button. Playback stops but the disc continues to spin and the

playback symbol blinks in the display.

Press the PLAY/PAUSE button again to release pause and resume normal

CD playback.

OPERATING INSTRUCTIONS

TO REPEATEDLY PLAY BACK ONE TRACK/ALL TRACKS

RANDOM PLAY BACK CD

PROGRAMMED PLAYBACK

The CD player in this unit has a 20 track programmable memory that allows you

to program up to 20 tracks on any disc for playback in any desired order. You

may program 20 different tracks or you may also program certain tracks to play

more than once.

To perform programmed playback, proceed as follows:

To repeat a single track, press the P-MODE/M-DN button once while in the

Stop mode; will show in the display. Press the REW SKIP TUNER-DN

or FEW. SKIP/TUNER-UP button to select the specific track that you wish to

repeat. When the desired track number appears in the display, press the

PLAY/PAUSE button to begin playback. The specific track you selected will

be repeated continuously.

To repeat all of the tracks on a disc continuously, press the P-MODE/M-DN

button twice while in the Stop mode; ALL will show in the display. Press

the PLAY/PAUSE button to begin playback; all the tracks on the CD will

repeat continuously.

To cancel Repeat Playback, press the P-MODE/M-DN button until the Repeat

indicator disappears from the display or press the STOP button.

Press P-MODE/M-DN button three times while in STOP MODE; "RAND" will

show in the display. Press PLAY/PAUSE button to begin RANDOM play.

To cancel RANDOM play, press the P-MODE/M-DN button until RANDOM

indicator disappears from the display.

Press the POWER button to turn the unit on.

Open the CD compartment lid by pressing the CD Door OPEN/CLOSE area

and insert your disc in the CD player with label side up. Close the CD

compartment door.

At STOP MODE, press the MEM/PROG CLK SET button; "P-01" (Program

Number) will show in the display and flash.

OPERATING INSTRUCTIONS

When the last programmed track has been played, the player will stop. To

begin the programmed playback again, press the PLAY/PAUSE button to begin

programmed playback again. To cancel the Programmed Playback mode, press

the POWER button or OPEN the CD door.

NOTES ON PROGRAMMED PLAYBACK:

LISTENING TO THE RADIO

Press the REW SKIP TUNER-DN or FEW. SKIP/TUNER-UP button to select

the track number (Example: Track 5) appears in the display, press the

MEMORY/CLOCK SET button. "P-02" indicating program 2 is ready to be

set. Then press the REW SKIP TUNER-DN or FEW. SKIP/TUNER-UP button

repeatedly to select a second track, press the MEMORY/CLOCK SET button

again.

After programming up to 20 tracks in the CD program Memory, press the

PLAY/PAUSE button to begin programmed playback; "PROG" will appear in

the display and playback will begin on the first track that you programmed.

The player will continue to play all of the tracks that you programmed in the

order in which you programmed them.

Press the STOP/BAND button to stop the program before it is finished.

You can skip through the program while it is playing using the REW SKIP

TUNER-DN or FEW. SKIP/TUNER-UP button.

Press the POWER button to turn the unit on.

Press the Function button to select the Tuner mode. Press the STOP/BAND

button to select AM or FM.

Use the REW SKIP TUNER-DN or FEW. SKIP/TUNER-UP button to select

the desired AM or FM station. When a strong FM Stereo signal is received,

the (ST) symbol will show in the display.

If you press and hold the REW SKIP/TUNER-DN or TUNER-UP button for

one second, then release, the unit will automatically scan to the next

broadcasting station.

Press the POWER button to turn the radio off.

OPERATING INSTRUCTIONS

HINTS FOR BETTER RECEPTION

FM - Make sure that the telescopic FM Rod Antenna is raised and extended to

its full length. You may have to vary the direction of the antenna to find the

strongest signal for each FM station.

AM - The AM ferrite bar antenna is located inside the cabinet. It may be

necessary to turn the unit slightly so that the internal antenna is pointing in the

direction of the AM transmitter. You may have to experiment to find the position

that provides the strongest reception for each your favorite AM section.

TO SET/RECALL THE RADIO PRESETS (20 FM/AM)

Press the POWER button to turn the unit on. Press the Function button to

select the Tuner mode.

Press the STOP/BAND button to select AM or FM. Use the REW SKIP

TUNER DN or TUNER UP button to select the desired AM or FM station.

Press the MEMORY/CLOCK SET button; "P-01" will blink in the display.

Press the MEMORY/CLOCK SET button again to set the preset. Repeat

steps 2 through 4 to set more presets.

The unit can preset 20 station totally for AM and FM.

When "P01-P20" is blinking, press REW SKIP TUNER-DN or FEW.

SKIP/TUNER-UP button to select the Preset number.

Press M-UP or M-DN to select your preset station.

OPERATING INSTRUCTIONS

PROGRAMMED REPEAT

PLAYING MP3 DISCS

MP3 SKIP/SEARCH

It is also possible to use the Program and Repeat functions together to repeat

a specific program indefinitely. First, program the tracks you wish to hear in

the order you wish to hear them, as described on the previous page. Then,

press the PLAY/PAUSE button to begin program playback.

Press the P-MODE/M-DN button twice; both indicators ALL will appear

in the display. The player will play the tracks you selected in the order in

which you programmed them. When the last track in the program has been

played, the entire program will begin again.

Programmed Repeat operation will continue indefinitely until you press the

STOP button, or turn the unit off.

Press the POWER button to turn the unit on and press the function button to

CD mode.

Open the door. Insert an MP3-encoded CD label side up. Close the CD door.

Press the PLAY/PAUSE Button. All the of the tracks will be played once.

Press the REW SKIP TUNER-DN or FEW.SKIP/TUNER-UP button to select

a particular track.

Press and hold REW SKIP TUNER-DN or FEW.SKIP/TUNER-UP button to

quickly advance through music.

Press ALBUM button once to select the current folder. Press ALBUM button

twice to select folder. When playing MP3 disc, press REW SKIP TUNER-DN

or FEW.SKIP/TUNER-UP button to select another track. Press ALBUM

button to indicate the current folder and press again to select the other folder.

Inhaltsverzeichnis

Andere Curtis CD-Player Handbücher

Curtis

Curtis CD182 Bedienungsanleitung

Curtis

Curtis CDMP364 Bedienungsanleitung

Curtis

Curtis RCD858 Bedienungsanleitung

Curtis

Curtis CD290 Bedienungsanleitung

Curtis

Curtis RCD824 Bedienungsanleitung

Curtis

Curtis CD156 Bedienungsanleitung

Curtis

Curtis Curtis RCD163A RCD163A RCD163A Bedienungsanleitung

Curtis

Curtis CD145 Bedienungsanleitung

Curtis

Curtis CD181 Bedienungsanleitung

Curtis

Curtis CD266 Bedienungsanleitung

Curtis

Curtis CD084B Bedienungsanleitung

Curtis

Curtis CD156UK Bedienungsanleitung

Curtis

Curtis CDMP366 Bedienungsanleitung

Curtis

Curtis iMODE IP2604UK Bedienungsanleitung

Curtis

Curtis CD150 Bedienungsanleitung

Curtis

Curtis RCD 310 Bedienungsanleitung

Curtis

Curtis RCD951 Bedienungsanleitung

Curtis

Curtis CD360 Bedienungsanleitung

Curtis

Curtis KCR2606 Bedienungsanleitung

Curtis

Curtis CD156UK Bedienungsanleitung

Curtis

Curtis CD149 Bedienungsanleitung

Curtis

Curtis IP2604 Bedienungsanleitung

Curtis

Curtis RCD670 Bedienungsanleitung

Curtis

Curtis RS59A Bedienungsanleitung

Beliebte CD-Player Handbücher anderer Marken

RCA

RCA RP-7923 Bedienungsanleitung

Pioneer

Pioneer DEH-P3550MP XM Bedienungsanleitung

Philips

Philips AZ1207 Bedienungsanleitung

Philips

Philips CD582 Bedienungsanleitung

Philips

Philips AZ 6821 Bedienungsanleitung

Lasonic

Lasonic MSU-2020 Bedienungsanleitung

THOMSON

THOMSON RCD150 Bedienungsanleitung

Denon

Denon DCD-1420 Bedienungsanleitung

Panasonic

Panasonic SJ-MR100 Bedienungsanleitung

Onkyo

Onkyo DX-7210 Bedienungsanleitung

Sony

Sony MZ-R3 Bedienungsanleitung

Denon

Denon DVM-4800 Bedienungsanleitung

JBL

JBL MR-32 Bedienungsanleitung

RCA

RCA RCD152 Bedienungsanleitung

Technics

Technics SL-PS770A Bedienungsanleitung

Clarion

Clarion compact disc Bedienungsanleitung

Sony

Sony MZ-M10 Bedienungsanleitung

Philips

Philips Expanium AZ 1538 Bedienungsanleitung