CyberPower OR600ERM1U Bedienungsanleitung

OR600ERM1U

OR650ERM1UGR

User’s Manual

K01-0000812-00

IMPORTANT SAFETY INSTRUCTIONS

This manual contains important instructions that should be followed during installation and

maintenance of the UPS and batteries. Please read and follow all instructions carefully during

installation and operation of the unit. Read this manual thoroughly before attempting to

unpack, install, or operate.

CAUTION! The UPS must be connected to a grounded AC power outlet with fuse or circuit

breaker protection. DO NOT plug the UPS into an outlet that is not grounded. If you need to

de-energize this equipment, turn off and unplug the UPS.

CAUTION! DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT! CyberPower

Systems does not sell products for life support or medical applications. DO NOT use in any

circumstance that would affect the operation or safety of any life support equipment, with any

medical applications, or patient care.

CAUTION! The battery can energize hazardous live parts inside even when the AC input

power is disconnected.

CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity

controlled indoor area, free of conductive contaminants. (Please see specifications for

acceptable temperature and humidity range).

CAUTION! To reduce the risk of electric shock, do not remove the cover, except to service

the battery. There are no user serviceable parts inside, except for the battery.

CAUTION! To avoid electrical shock, turn off the unit and unplug it from the AC power source

before servicing the battery or installing a computer component.

CAUTION! DO NOT USE WITH OR NEAR AQUARIUMS! To reduce the risk of fire, do not

use with or near aquariums. Condensation from the aquarium can come in contact with metal

electrical contacts and cause the machine to short out.

INSTALLING YOUR UPS SYSTEM

UNPACKING

The box should contain the following:

(1) USB cable (A+B type) x1; (2) power cord x4; (3) user manual x1; (4) UPS unit x1.

*PowerPanel® Business software is available on our website.

Please visit www.cyberpower.com and go to the Software Section for free download.

OVERVIEW

The OR600ERM1U/OR650ERM1UGR provides automatic voltage regulation for inconsistent utility

power. The OR600ERM1U/OR650ERM1UGR features 1030 Joules of surge protection, and provides

battery backup during power outages. The OR600ERM1U/OR650ERM1UGR ensures consistent

power to your computer system and its included software will automatically save your open files and

shutdown your computersystem during a utility power loss.

HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT

1.Make sure that the total Volt-Amp (VA) requirements of your computer, monitor, and

peripheral equipment does not exceed 600VA.

2.Ensure that the equipment plugged into the battery power-supplied/surge outlets does

not exceed the UPS unit's rated capacity (600VA/360W for OR600ERM1U; 650VA/360W for

OR650ERM1UGR). If the rated unit capacities are exceeded, an overload condition may occur and

cause the UPS unit to shut down and the circuit breaker to trip.

BASIC OPERATION

DESCRIPTION

1. LCD Module Display

High resolution and intelligent LCD display shows all the UPS information with icons and

messages. For more information please check the “Definitions for Illuminated LCD Indicators”

section.

2. Power On Indicator

It illuminates when the UPS outlets are providing power, free of surges and spikes.

3. Power Switch

Used as the master on/off switch for equipment connected to the battery power supplied outlets.

4. LCD Display Toggle/Selected Switch

The switch can be used to select the LCD display contents including Input Voltage, Output Voltage

and Estimated Run Time.

5. Battery and Surge Protected Outlets

The unit has four battery powered/surge protected outlets for connected equipment and ensures

temporary uninterrupted operation of your equipment during a power failure.

6. Full-Time Surge Protection Outlets

The unit has two always on surge suppression outlets.

7. Expansion Port

Allows users to add the optional SNMP card.

8. Communication Protection Ports

Communication protection ports will protect any standard modem, fax, telephone line, broadband

network or Ethernet connection.

9. USB Port to PC

The USB port allow communication from the UPS to the computer. The UPS communicates its

status to the PowerPanel® Business software when connected with a USB port.

10. Serial Port to PC

The port allows connection and communications from the DB-9 serial on the computer to the UPS

unit.

11. Circuit Breaker

Located on the side of the UPS, the circuit breaker serves to provide overload and fault protection.

12. AC Input

Connect the AC Power cord to a properly wired and grounded outlet.

HARDWARE INSTALLATION GUIDE

1. Your new UPS may be used immediately upon receipt. However, recharging the battery for

at least 8 hours is recommended to ensure that the battery's maximum charge capacity

is achieved. Charge loss may occur during shipping and storage. To recharge the battery,

simply leave the unit plugged into an AC outlet. The unit will charge in both the on and off

position.

2. With the UPS unit off and unplugged, connect the computer, monitor, and any externally

powered data storage device (Zip drive, Jazz drive, Tape drive, etc. into the battery power

supplied outlets. DO NOT plug a laser printer, copier, space heater, vacuum, paper

shredder or other large electrical device into the UPS. The power demands of these

devices will overload and possibly damage the unit.

3. To protect a fax, telephone, modem line or network cable, connect a telephone cable or

network cable from the wall jack outlet to the IN jack of the UPS. Then connect a telephone

cable or network cable from the OUT jack on the UPS to the modem, computer, telephone,

fax machine, or network device.

4. Plug the UPS into a 2 pole, 3 wire grounded receptacle (wall outlet). Make sure the wall

branch outlet is protected by a fuse or circuit breaker and does not service equipment with

large electrical demands (e.g. air conditioner, refrigerator, copier, etc. Avoid using

extension cords. If used, the extension cord must be grounded and rated for 15 amps.

5. Depress the power switch to turn the unit on. The power on indicator light will illuminate

and the unit will "beep".

6. If an overload is detected, an audible alarm will sound and the unit will emit one long beep.

To correct this, turn the UPS off and unplug at least one piece of equipment from the

battery power supplied outlets. Wait 10 seconds. Make sure the circuit breaker is

depressed and then turn the UPS on.

7. To maintain optimal battery charge, leave the UPS plugged into an AC outlet at all times.

8. To store your UPS for an extended period, cover it and store with the battery fully

charged. Recharge the battery every three months to ensure battery life.

CYBERPOWER GREENPOWER UPS TECHNOLOGY

CyberPower’s Green Commitment

CyberPower is dedicated to the development of green products, and has adopted

Green practices throughout its business, including: membership in Climate Savers

Computing Initiative (CSCI), accordance with the Restriction on Hazardous

Substances (RoHS), Waste Electrical and Electronic Equipment (WEEE) protocols,

as well as ISO 14001 and IECQ QC080000. CyberPower pledges to provide the

advanced energy solution for the environment and become a leading eco-friendly

organization in the UPS industry.

Reduce Energy Cost with GreenPower UPSTM Technology

CyberPower’s goal is not only to provide eco-friendly products but also to bring the best value for

consumers. The advanced energy-saving design improves the operating efficiency and eliminates

waste energy consumption. As a result, consumers will enjoy significant energy cost savings with the

adoption of GreenPower UPSTM technology.

BATTERY REPLACEMENT

CAUTION! Read and follow the IMPORTANT SAFETY INSTRUCTIONS before servicing the

battery. Service the battery under the supervision of personnel knowledgeable of

batteries and their precautions.

CAUTION! Use only the specified type of battery. See your dealer for replacement batteries.

CAUTION! The battery may present the risk of electrical shock. Do not dispose of batteries in

a fire, as they may explode. Follow all local ordinances regarding proper disposal of batteries.

CAUTION! Do not open or mutilate the batteries. Released electrolyte is harmful to the skin

and eyes and may be toxic.

CAUTION! A battery can present a high risk of short circuit current and electrical shock. Take

the following precautions before replacing the battery:

1. Remove all watches, rings or other metal objects.

2. Only use tools with insulated handles.

3. DO NOT lay tools or other metal parts on top of battery or any battery terminals.

4. Wear rubber gloves and boots.

5. Determine if the battery is inadvertently grounded. If inadvertently grounded, remove source

of ground. CONTACT WITH A GROUNDED BATTERY CAN RESULT IN ELECTRICAL

SHOCK! The likelihood of such shock will be reduced if such grounds are removed during

installation and maintenance (applicable to a UPS and a remote battery supply not having a

grounded circuit)

BATTERY REPLACEMENT PROCEDURE:

REMINDER: Batteries are consider HAZARDOUS WASTE and must be disposed of properly. Almost any

retailer that sells lead-acid batteries collects used batteries for recycling, as required by most state laws.

2. Remove the three retaining screws on the

cable protection cover then remove the cover

faceplate.

1. Remove the right-side of the faceplate.

3. Disconnect the black and red cables.

4. Remove the retaining screw of the cable

connectors.

5. Replace the new battery pack. Assemble the screws, cover,

cable and front panel in the reverse sequence of above steps.

Recharge the unit for 4-8 hours to ensure the UPS performs

expected runtime.

LCD FUNCTION SETUP GUIDE

Power Switch

Power On:

Press and hold the POWER button. You will hear a

constant tone for 1 second, followed by a short beep.

Release the button after the short beep.

Power Off:

Press and hold the POWER button. You will hear a

constant tone for 1 second, followed by two short

beeps. Release the button after the two short beeps.

LCD Display Toggle/Selected Switch

Enter Setup Mode:

Press the select button for approximately 3 seconds to

access the 11 functions of the setup mode: Local

Power Quality, High Transfer Voltage, Low Transfer

Voltage, Sensitivity, Low Battery Warning, Self Test,

Buzzer Setting, LCD Sleep, Last Fault Reason, Back to

default, Escape item.

Select Function:

Short press the toggle to switch from the current item to

the next item.

Confirm Option:

When an option is selected, press the toggle for 3

seconds. The icons will stop flashing after the setting

has been confirmed

Function LCD Display Options Default Description

Local

Power

Quality

▃ Low

▃▄ Normal

▃▄▅▆ High

Customer

(CUS)

*Only when high/ low

transfer voltage is

configured

Normal

(195V-25

7V)

This function

determines how the

UPS switch to Battery

Mode.

3 different output

voltage ranges can be

chosen according to the

quality of the AC utility

service in your location.

If your utility service is

not stable, you can

select Low

(189V~271V). The UPS

will go to Battery Mode

less often to tolerate the

utility power

fluctuations.

If your utility service is

stable, you can select

High (207V~253V). The

unit will go to Battery

Mode more often.

High

Transfer

Voltage

253V-271V 257V In Local Power Quality

settings, 10 fixed

voltage ranges can be

chosen. However, you

can fine tune the High

Transfer Voltage in this

function.

If the utility voltage is

usually high, and the

connected equipment

can work in this

condition, you can set

the output voltage

range higher to reduce

the UPS from going to

Battery Mode as often.

Low

Transfer

Voltage

189V-207V 195V In Local Power Quality

settings, 10 fixed

voltage ranges can be

chosen. However, you

can fine tune the Low

Transfer Voltage in this

function.

If the utility voltage is

usually low, and the

connected equipment

can work in this

condition, you can set

the output voltage

range lower to reduce

the UPS from going to

AVR Mode or Battery

Mode as often.

Sensitivity ▃ Low

▃▄ Normal

▃▄▅▆ High

Normal If the connected

equipment can tolerate

more power events

(Example: unstable

power often associated

with stormy weather),

select Low Sensitivity.

The UPS will go to

Battery Mode less

often. If the connected

equipment is more

sensitive to power

events, select High

Sensitivity. The UPS

will go to Battery Mode

more often.

Low Battery

Warning 5/6/7/8 mins 5 mins The audible alarm will

continuously beep

when the remaining

runtime is less than the

selected value.

Self Test Yes

Escape to function menu

No Action

In Line Mode, select

YES to perform a Self

Test on the battery.

Buzzer

Setting Buzzer on

Buzzer off

Buzzer on

“b.on” is buzzer

enabled; “b.oF” is

buzzer disabled.

If b.oF is selected, the

unit will mute all alarms

except for fault or

overload condition.

LCD Sleep

Auto off

Always on

L.on

“L.on” (Auto Off is on):

In Line Mode, LCD

screen will off

automatically after 1

min of inactivity; in

Battery Mode, LCD

screen is always on.

“L.oF” (Auto Off is off):

LCD screen is always

on.

Last Fault

Reason

There is no confirm

page for this item. It will

only show the error

code for last fault

reason.

E01 : Charger fault

(Over Charge).

E02 : Charger fault (No

Charge)

E11 : Battery Fault

E21 : Output short.

E22 : Over load.

Back to

Default

No Action

Select Yes to restore

the UPS factory default

settings.

Escape

Item

Return to the previous

page.

TECHNICAL SPECIFICATIONS

Model OR600ERM1U OR650ERM1UGR

Capacity (VA) 600VA/360W 650VA/360W

Input

Frequency Range 47Hz-63Hz (Auto Sensing)

AVR Function Yes

Output

On Battery Output

Voltage 230Vac +/-10%

On Battery Output

Frequency 50/60Hz +/-1%

Overload Protection On Utility: Circuit Breaker, On Battery: Internal Current Limiting

Surge Protection

Lightning / Surge

Protection Yes

Network/ Phone/ Fax/

Modem Protection RJ45 ( One In/ One Out )

Operating

Temperature +32F to 104F ( 0C to 40C )

Physical

Total # of UPS outlets 6 ( Backup x 4 ) 4

Maximum

Dimensions(LxWxH) 1U Rack 433x235x44mm

Weight 7.8 kg

Battery

Sealed Maintenance

Free Lead Acid

Battery

6V / 8Ah x 2

Typical Recharge

Time 8 hours

User Replaceable Yes

Status Indicators

Indicators Power On, Wiring Fault, LCD Display

Audible Alarms On Battery, Low Battery, Overload

Management

Self -Test Yes

Auto-Charger Yes

Auto-Restart Yes

USB interface Yes

Dry Contact Yes

SNMP/HTTP

Networking Option

TROUBLESHOOTING

Problem Possible Cause Solution

Full

time surge protection

outlets stop providing power

to equipment. Circuit

breaker button is projecting

from the side of the unit.

Circuit breaker has

tripped due to an

overload.

Turn the UPS off and unplug at least one

piece of equipment. Wait 10 seconds, reset

the circuit breaker by depressing the button,

and then turn the UPS on.

The UPS does not perform

expected runtime.

Battery not fully

charged.

Recharge the battery by leaving the UPS

plugged in.

Battery is slightly worn

out.

Contact CyberPower Systems about

replacement batteries at

support@cpsww.eu

The UPS will not turn on.

The on/off switch is

designed to prevent

damage by rapidly

turning it off and on.

Turn the UPS off. Wait 10 seconds and then

turn the UPS on.

The battery is worn out.

Contact CyberPower Systems about

replacement batteries at

support@cpsww.eu

Mechanical problem.

Contact CyberPower Systems at

support@cpsww.eu

PowerPanel® Business is

inactive.

USB cable is not

connected.

Connect USB cable to the UPS

unit and an

open USB port on the back of the computer.

The unit is not providing

battery power.

Shutdown your computer and tu

rn the

UPS off. Wait 10 seconds and turn the

UPS back on. This should reset the unit.

Additional troubleshooting information can be found at www.CyberPower.com

For more information, visit www.CyberPower.com or contact

Cyber Power Systems, Inc.

E-MAIL: sales@cpsww.eu

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere CyberPower UPS Handbücher

CyberPower

CyberPower Value Pro 700VA Bedienungsanleitung

CyberPower

CyberPower OLS1000ERT2U Bedienungsanleitung

CyberPower

CyberPower Value1200ELCD Bedienungsanleitung

CyberPower

CyberPower STP3T10KE Bedienungsanleitung

CyberPower

CyberPower OR1000PFCRT2U Bedienungsanleitung

CyberPower

CyberPower OR1500LCDRTXL2U Bedienungsanleitung

CyberPower

CyberPower Surge Buster SB501BA-FR Bedienungsanleitung

CyberPower

CyberPower 649532012855 Bedienungsanleitung

CyberPower

CyberPower CP750LCD Bedienungsanleitung

CyberPower

CyberPower 649532006854 Bedienungsanleitung

CyberPower

CyberPower SE450G1 Bedienungsanleitung

CyberPower

CyberPower PowerPanel Cloud Bedienungsanleitung

CyberPower

CyberPower OR1000LCDRM1U Bedienungsanleitung

CyberPower

CyberPower OfficePower 1250AVR Bedienungsanleitung

CyberPower

CyberPower CPS1000EI Bedienungsanleitung

CyberPower

CyberPower CyberShield CS16U48V-8 Bedienungsanleitung

CyberPower

CyberPower ST425 Bedienungsanleitung

CyberPower

CyberPower CST625G Bedienungsanleitung

CyberPower

CyberPower PR3000LCDRT2U Bedienungsanleitung

CyberPower

CyberPower PR1500 Bedienungsanleitung

CyberPower

CyberPower Professional Tower UPS PP1100E Bedienungsanleitung

CyberPower

CyberPower CPS600E Bedienungsanleitung

CyberPower

CyberPower PR3000LCDRT2U Bedienungsanleitung

CyberPower

CyberPower UT400EG Bedienungsanleitung

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Mecer

Mecer ME-1000-WTU Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

Eaton

Eaton 3S Montageanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung

ZincFive

ZincFive BC Series Bedienungsanleitung

BPC

BPC 1.5K SMART Bedienungsanleitung

IBM

IBM 5595-1AX Bedienungsanleitung