CYCROWN CycFree Bedienungsanleitung

USER MANUAL
WWW.CYCROWN.COM
CycFree
SUPPORT@CYCROWN.COM

Contents
What’s Included in the Box 01
Installation 02
How to Charge the Battery 07
Drive Modes 09
Display and Buttons 10
For Your Safety 16
Battery Maintenance 17
Storage 18
Scrap Disposal 18
Specification 19
Warranty 20
Contact Us 21

PRODUCT OVERVIEW
Gear Lever
LCD Display
Brake Lever
Stem
Front light
Hydraulic Suspension
Front Fork
Front Mudguard
Slow ReleaseMotor Pedal Disc Brake
Handle Bar
Saddle
Charging Port
On/Off Switch
Battery
Bicycle Carrier
Taillight
01
1x Bike Frame
+ Rear Wheel
1x Charger 1x Front Fender 1x User Manual 2x Battery Key
1x Front Wheel 2x Pedal 3x Hex Key
+2 x Wrench
User’s
Manual
1x Bicycle Pump
1x QR Skewer
Check the parts and accessories carefully. If there are missing or damaged parts/accesso-
ries, please contact online customer service support.

02
Step 1 Stem Installation
Insert the stem into the head
tube.
1Adjust the handlebar to make it
perpendicular to the front tire.
2Open the folding lock.
3
Put down the stem.
4Tighten the bolt into the head
tube.
5After tightening the bolt, Lift
the stem and close the
folding lock firmly.
6
90°
● Please read this manual thoroughly and follow its instructions.
● Make sure all parts are intact.
● Do not install the battery or start the computer until the bike is fully installed.
● If you have any questions or can't find the information you need in the manual, please contact
us via email.
Before Installation
Installation

03
Insert the front axle into the wheel hub from one side and
install the bushings, spacers, safety hooks, spacers, and nuts
on the axle in sequence from both sides
2
Lower the front fork onto the front wheel with the bushings
and spacers located on the inside of the front fork
dropouts. Make sure the brake caliper grips the brake rotor
3
Adjust the safety hook to hook the front fork, and check that
the front fork dropouts, safety hooks, spacers, and nuts are in
sequence from the wheel hub to the outside. After ensuring
the correct order, tighten the nuts with wrenches
4
Step 3 Front Wheel Installation
After taking out the front wheel, remove the front fork from
the fork mount
1
Step 2 Handlebar Angle Adjustment
Make sure the handlebar is perpendicular to the
front wheel.
2
To adjust the handlebar angle, Open the quick
release connecting the handlebar and stem.
1

04
Step 4 Front Light and Mudguard Installation
Put the fender through the front fork. Reinstall the
bolts, washers and nuts (in this order). Reinstall
the lower fender screws.
2
Take out the front fender and remove the nuts,
washers and bolts on the top and bottom of the
front fork.
1
Tighten the screws with the hex key and wrench.
4
Put screws into the front light bracket and align.
3
Warnings:
● The disc brake is located on the left side in the direction of riding.
● Make sure the front wheel hub is fully engaged into the front fork drop-outs.
● Ensure that the circumference of the front wheel is completely caught in the drop-outs of the
front fork, and tighten the nuts on both sides.

05
Press the pedals firmly by hand first. Tighten the
right pedal clockwise and the left pedal
counterclockwise.
2
Identify the correct side by finding ‘R’ and ‘L’
marks on the pedals.
1
Push the pedal inward to fold the pedals up or
down.
4
Fully tighten the pedals with a pedal wrench or
open-end wrench.
3
Step 5 Pedal Installation
L LR R
L R L R

06
Step 6 Seat Installation
Open the QR seatpost clamp and
adjust the seat height by pulling up
or pressing down the seat.
1Close the seatpost clamp and make sure
the seatpost is held in place. Don’t adjust
the seat too high (keep the safety line
mark lower than the top of the seat tube).
2Loosen the seat clamp and adjust
the seat to an appropriate angle.
3
Step 7 Battery Removal and Installation
To reinstall the battery, align the slot on the
bottom of the battery and reinsert the
battery into the frame. Turn the key to the
locked position. If you want to know the
battery level without turning the power on,
long press the button on the top of the
battery to display the current battery level.
( For your convenience, the bike battery can be removed.)
21 Insert the battery key, Turn it to the unlocked
position.
The battery is installed into the frame and can be
taken out from the folded position of the frame.
3The battery is installed into the frame and can be
taken out from the folded position of the frame.

07
32 Plug the charger AC plug into a wall socket
(100V-240V), and plug the DC connector into the
electric bike's charging port.
After charging for about 7 hours, the indicator light of
the power adapter will change from red to green.
Disconnect all cables when charging is complete.
Make sure the power is turned off and check the connection of the charging cable and power adapter.
1
How to Charge the Battery
For your convenience, the battery can also be charged when removed from the
CYCROWN CycFree e-bike.
Charge your e-bike before the first ride. It takes about 7 hours to fully charge the battery.

08
Battery Safety
● Please fully charge the battery before first use. It takes 7 hours.
● Periodically visually inspect the battery connector and charging cable.
● Always keep the charging environment clean and dry.
● Do not charge the e-bike if there is liquid on the charging port.
● Avoid charging your e-bike in extremely hot or cold conditions to take full advantage of the battery's maximum
efficiency. Under no circumstances should you use the bike while it is charging or connected to a charger.
● The charging time is about 7 hours. Prolonged charging may reduce battery life and performance.
● Only use the charger that comes with the e-bike. If the official charger is lost or damaged, Please contact
Customer Service for a replacement.
● Before using the e-bike, Be sure to lock the battery with the provided battery key and remove the battery key.
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere CYCROWN Fahrrad Handbücher


















