Cypress CY3274-HV Bedienungsanleitung

CY3274-HV PLC DEVELOPMENT KIT

QUICK START GUIDE

Using the CY3274-HV High Voltage 110-240 V AC PLC Development Kit

To evaluate this kit, a second CY3274 kit is needed. This guide assumes that two CY3274 kits are available.

1. Install CY3274 Kit installer from the kit website. Open PSoC

Programmer from Start menu.

2. Set AutoDetection to Off, set the ‘Device Family’ to

CY8C-PLC-LED16P, ‘Device’ to CY8CPLC20-OCD, programming

mode to Reset and Verification to either option.

3. Open the CY3274_PLC_Demo.hex file from the firmware ->

CY3274_PLC_Demo inside CY3274 kit installation folder.

1. Connect the USB cable from the PC to the MiniProg programmer.

Connect the MiniProg to the ISSP header J21 on kit 1.

2. In PSoC Programmer, power the device by clicking ‘Toggle Power’

button. Click the Program button (downward arrow). When the

status says ‘Programming Successful’, remove the MiniProg from

the ISSP header.

3. Repeat the above programming operation on kit 2.

1. Connect the LCD Module to LCD1 header.

2. On kit 1, connect a jumper wire from SW (on J18) to P0[1] (on

J13), from P0[4] to one of the 8 DIP switches on J12 (the 8 DIP

switch array on S3 is connected to J12) and from P0[7] to another

DIP switch.

3. Repeat steps 1 and 2 on kit 2 as well.

4. Put the 2 DIP switches (S3) on kit 1 to ON position to set it as Tx

and the 2 DIP switches on kit 2 to OFF position to set it as Rx.

1. Connect the power cable from the AC mains to the AC power

connector on the first CY3274 kit. The blue LED (DS1) turns on.

Repeat the same for kit 2.

1. Push the reset button S2 on both nodes. A message “PLC Demo”

initially appears on the LCD. The kit will be a transmitter if the DIP

switch connected to P0[7] is pulled high, else the kit will act as a

receiver.

2. Press the push button (S4) on transmitter to start transmission of

packets upto a packet count of 1000. The LCD shows transmission

statistics.

3. Transmission can be started or halted (if transmission is in progress)

or resumed (if transmission is halted) or restarted (when the packet

count of 1000 is completed) by pressing the push button (S4) on

the transmitter kit.

4. Received packet count can be reset by pressing the push button

(S4) on the receiver kit.

CAUTION: High Voltage (Risk of Electric Shock)

All work in powerline communications must be done with extreme care.

Caution must be exercised when using power supplies or power related equipment.

CY3274-HV PLC DEVELOPMENT KIT

QUICK START GUIDE

respective owners. DOC#: 001-54836 REV *E

www.cypress.com/go/plc

For the latest information about this kit visit

CY3274-HV Top View

CAUTION: High Voltage (Risk of Electric Shock)

All work in powerline communications must be done with extreme care.

Caution must be exercised when using power supplies or power related equipment.

The protective plastic encasing must always be fixed to the board when the kit is in operation.

Potentiometer R47

(Connected to VR)

High Voltage AC-DC

Power Supply

High Voltage PLC

Coupling Circuit

RS232 Interface

I2C Connector (J15)

and Jumpers

(JP1, JP3, JP4, JP5)

LCD Connector

(Connected to Port 4)

Push-button S4

(Connected to SW)

Potentiometer R46

(For LCD Contrast)

Transmit Filter, Transmit

Amplifier, and Receive Filter

Reset Push-button (S2)

CY8CPLC20 PLC Device

with On-Chip Debugger (U1)

General LEDs

(Connected to LED1-4)

ISSP Programming

Connector (J21)

RJ45 Debugger

Connector (J14)

PLC Rx, Tx,

Band-In-Use Indicator

LEDs (DS2, DS3, DS4)

AC Power

Connector (J7)

Breadboard with

surrounding GPIO Headers

DIP Switch S3

(Connected to J12)

Andere Cypress Mikrocontroller Handbücher

Cypress

Cypress FM3 Series Bedienungsanleitung

Cypress

Cypress CY8CKIT-042-BLE-A Bedienungsanleitung

Cypress

Cypress MB95580H Series Bedienungsanleitung

Cypress

Cypress CY3274 Bedienungsanleitung

Cypress

Cypress PSoC CY8CKIT-048 Bedienungsanleitung

Cypress

Cypress CY3668 Bedienungsanleitung

Cypress

Cypress CY3280-CPM1 Bedienungsanleitung

Cypress

Cypress CY3641 Bedienungsanleitung

Cypress

Cypress CY8CKIT-062-BLE Bedienungsanleitung

Cypress

Cypress PERFORM MB96630 Series Bedienungsanleitung

Cypress

Cypress CYUSBS234 Bedienungsanleitung

Cypress

Cypress EZ-USB CYUSB3KIT-001 Bedienungsanleitung

Cypress

Cypress CY8CKIT-016 Bedienungsanleitung

Cypress

Cypress CY4531 EZ-PD CCG3 EVK Bedienungsanleitung

Cypress

Cypress FR Series Bedienungsanleitung

Cypress

Cypress CY8CKIT-030 Bedienungsanleitung

Cypress

Cypress CY8CKIT-147 Handbuch

Cypress

Cypress MB96640 Series Bedienungsanleitung

Cypress

Cypress FM0+ S6E1C SERIES Bedienungsanleitung

Cypress

Cypress MB95710M Series Bedienungsanleitung

Cypress

Cypress PSoC CY8CKIT-062-WiFi-BT Bedienungsanleitung

Cypress

Cypress CY3660 enCoRe V Bedienungsanleitung

Cypress

Cypress CY3280-BSM Bedienungsanleitung

Cypress

Cypress CY4607 HX2VL Bedienungsanleitung

Beliebte Mikrocontroller Handbücher anderer Marken

AMS

AMS AS7261 Demo Kit Bedienungsanleitung

Novatek

Novatek NT6861 Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266 SDK Einrichtungshandbuch

Nuvoton

Nuvoton ISD61S00 ChipCorder Leitfaden

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Bedienungsanleitung

Texas Instruments

Texas Instruments Chipcon CC2420DK Bedienungsanleitung

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Bedienungsanleitung

NEC

NEC 78GK0S/K 1+ Series Montage- und Bedienungsanleitung

Mikroe

Mikroe SEMITECH N-PLC Click Montage- und Bedienungsanleitung

Intel

Intel Agilex Bedienungsanleitung

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Bedienungsanleitung

Texas Instruments

Texas Instruments TMS320F2837 D Series Bedienungsanleitung

CYPRES

CYPRES CY14NVSRAMKIT-001 Bedienungsanleitung

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266EX Betriebsanleitung

Abov

Abov AC33M8128L Bedienungsanleitung

Laird

Laird BL654PA Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories C8051F800 Bedienungsanleitung