Cypress PSoC 4 M Series Bedienungsanleitung

CY8CKIT-043

PSoC®4 M-Series Prototyping Kit Guide

Doc. #: 001-97606 Rev. **

Cypress Semiconductor

198 Champion Court

San Jose, CA 95134-1709

Phone (USA): +1.800.858.1810

Phone (Intnl): +1.408.943.2600

www.cypress.com

Copyrights

CY8CKIT-043 PSoC® 4 M-Series Prototyping Kit Guide, Doc. #: 001-97606 Rev. ** 2

Copyrights

Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress

product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor

intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express

written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-

support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The

inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use

and in doing so indemnifies Cypress against all charges.

Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by

and subject to worldwide patent protection (United States and foreign), United States copyright laws and international treaty

provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create

derivative works of, and compile the Cypress Source Code and derivative works for the sole purpose of creating custom

software and or firmware in support of licensee product to be used only in conjunction with a Cypress integrated circuit as

specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this

Source Code except as specified above is prohibited without the express written permission of Cypress.

Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS

MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS

FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials

described herein. Cypress does not assume any liability arising out of the application or use of any product or circuit

described herein. Cypress does not authorize its products for use as critical components in life-support systems where a

malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product

in a life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies

Cypress against all charges.

Use may be limited by and subject to the applicable Cypress software license agreement.

PSoC and CapSense are registered trademarks and PSoC Creator, PRoC, and EZ-BLE are trademarks of Cypress

Semiconductor Corp. All other trademarks or registered trademarks referenced herein are property of the respective

corporations.

Flash Code Protection

Cypress products meet the specifications contained in their particular Cypress PSoC Data Sheets. Cypress believes that its

family of PSoC products is one of the most secure families of its kind on the market today, regardless of how they are used.

There may be methods, unknown to Cypress, that can breach the code protection features. Any of these methods, to our

knowledge, would be dishonest and possibly illegal. Neither Cypress nor any other semiconductor manufacturer can

guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as ‘unbreakable’.

Cypress is willing to work with the customer who is concerned about the integrity of their code. Code protection is constantly

evolving. We at Cypress are committed to continuously improving the code protection features of our products.

CY8CKIT-043 PSoC® 4 M-Series Prototyping Kit Guide, Doc. #: 001-97606 Rev. ** 3

Contents

Safety Information 5

1. Introduction 7

1.1 Kit Contents .................................................................................................................7

1.2 PSoC Creator ..............................................................................................................8

1.2.1 PSoC Creator Code Examples ........................................................................9

1.2.2 Kit Code Example ..........................................................................................10

1.2.3 PSoC Creator Help ........................................................................................10

1.3 Getting Started...........................................................................................................11

1.4 Additional Learning Resources..................................................................................11

1.5 Technical Support......................................................................................................12

1.6 Document Conventions .............................................................................................12

2. Software Installation 13

2.1 Before You Begin.......................................................................................................13

2.2 Install Software ..........................................................................................................13

2.3 Uninstall Software......................................................................................................15

3. Kit Operation 16

3.1 Theory of Operation...................................................................................................16

3.2 KitProg .......................................................................................................................17

3.3 Programming and Debugging the PSoC 4 Target Device .........................................17

3.3.1 Programming Using PSoC Creator ................................................................17

3.3.2 Debugging Using PSoC Creator ....................................................................19

3.3.3 Programming Using PSoC Programmer ........................................................19

3.4 USB-UART Bridge .....................................................................................................19

3.5 USB-I2C Bridge .........................................................................................................19

3.6 Updating the KitProg Firmware..................................................................................19

4. Hardware 20

4.1 Board Details .............................................................................................................20

4.2 Hardware Details .......................................................................................................22

4.2.1 Target Board...................................................................................................22

4.2.2 KitProg Board.................................................................................................23

4.2.3 Power Supply System ....................................................................................24

4.2.4 Board Separation (Snapping).........................................................................24

4.2.5 Header Connections ......................................................................................25

4.2.6 User and Passive Inputs ................................................................................28

4.2.7 EZ-BLE PRoC Module ...................................................................................30

CY8CKIT-043 PSoC® 4 M-Series Prototyping Kit Guide, Doc. #: 001-97606 Rev. ** 4

Contents

5. Code Examples 33

5.1 Using the Kit Code Example......................................................................................33

5.2 Using Built-in PSoC Creator Code Examples with the Kit .........................................37

Appendix 42

PSoC 4 M-Series Prototyping Kit Schematics ....................................................................42

Programming the PSoC 4 M-Series Prototyping Kit Using MiniProg3/KitProg ...................44

Bill of Materials ....................................................................................................................45

Revision History 47

CY8CKIT-043 PSoC® 4 M-Series Prototyping Kit Guide, Doc. #: 001-97606 Rev. ** 5

Safety Information

Regulatory Compliance

The CY8CKIT-043 PSoC®4 M-Series Prototyping Kit is intended for use as a development platform

for hardware or software in a laboratory environment. The board is an open system design, which

does not include a shielded enclosure. This may cause interference to other electrical or electronic

devices in close proximity. In a domestic environment, this product may cause radio interference. In

such cases, take adequate preventive measures. In addition, this board should not be used near any

medical equipment or RF devices.

Attaching additional wiring to this product or modifying the product operation from the factory default

may affect its performance and cause interference with other apparatus in the immediate vicinity. If

such interference is detected, suitable mitigating measures should be taken.

The CY8CKIT-043 PSoC 4 M-Series Prototyping Kit, as shipped from the factory, has been verified

to meet with requirements of CE as a Class A product.

The kit contains ESD-sensitive devices. Electrostatic charges readily

accumulate on the human body and any equipment, and can discharge

without detection. Permanent damage may occur on devices subjected

to high-energy discharges. Proper ESD precautions are recommended

to avoid performance degradation or loss of functionality. Store unused

kit boards in the protective shipping package.

End-of-Life/Product Recycling

This kit has an end-of life five years from the date of manufacture

mentioned on the back of the box. Contact your nearest recycler to

dispose the kit.

CY8CKIT-043 PSoC® 4 M-Series Prototyping Kit Guide, Doc. #: 001-97606 Rev. ** 6

General Safety Instructions

ESD Protection

ESD can damage boards and associated components. Cypress recommends that you perform

procedures only at an ESD workstation. If such a workstation is not available, use appropriate ESD

protection by wearing an antistatic wrist strap attached to the chassis ground (any unpainted metal

surface) on your board when handling parts.

Handling Boards

The CY8CKIT-043 PSoC 4 M-Series Prototyping boards are sensitive to ESD. Hold the board only

by its edges. After removing the board from its box, place it on a grounded, static-free surface. Use a

conductive foam pad if available. Do not slide board over any surface.

CY8CKIT-043 PSoC® 4 M-Series Prototyping Kit Guide, Doc. #: 001-97606 Rev. ** 7

1. Introduction

Thank you for your interest in the CY8CKIT-043 PSoC®4 M-Series Prototyping Kit. This kit is

designed as an easy-to-use and inexpensive prototyping platform. It supports the PSoC 4 M-Series

device family, delivering a complete system solution for a wide range of embedded applications at a

very low cost. The PSoC 4200M device is an expansion of the PSoC 4 device family, which offers

more flash, GPIOs, and programmable analog and digital blocks. The PSoC 4200M device is a true

programmable embedded system-on chip, integrating custom analog and digital peripheral

functions, memory, and an ARM®Cortex®-M0 microcontroller on a single chip. The programmable

analog and digital peripheral functions allow higher flexibility, in-field tuning of the design, and faster

time-to-market.

The PSoC 4 M-Series Prototyping Kit offers an open footprint breakout board to maximize the end-

utility of the PSoC 4200M device. This kit provides a low-cost alternative to device samples while

providing a platform to easily develop and integrate the PSoC 4200M device into your end-system.

In addition, the board includes the following features:

■Onboard CMOD capacitors to enable CapSense®development

■Bypass capacitors to ensure high-quality ADC conversions

■An LED to provide feedback

■A push button to provide a simple user input

■Load capacitors to connect the 32-kHz external crystal oscillator

■3.3-V to 5.5-V operation

The PSoC 4 M-Series Prototyping Kit also integrates the Cypress KitProg, which enables onboard

programming, debugging, and bridging functionality, such as USB-UART and USB-I2C. The KitProg

is used to program and debug the target PSoC 4200M device (see Figure 1-1). The prototyping kit

allows you to separate the KitProg board from the PSoC 4 M-Series target board.

1.1 Kit Contents

This kit contains only the PSoC 4 M-Series Prototyping Kit board.

Figure 1-1. CY8CKIT-043 PSoC 4 M-Series Prototyping Kit

PSoC 4200M Target

KitProg

CY8CKIT-043 PSoC® 4 M-Series Prototyping Kit Guide, Doc. #: 001-97606 Rev. ** 8

Introduction

1.2 PSoC Creator

PSoC Creator™ is a state-of-the-art, easy-to-use integrated design environment (IDE). It introduces

revolutionary hardware and software co-design, powered by a library of preverified and

precharacterized PSoC Components. With PSoC Creator, you can:

1. Drag and drop Components to build your hardware system design in the main design workspace

2. Codesign your application firmware with the PSoC hardware

3. Configure Components using configuration tools

4. Explore the library of 100+ Components

5. Review Component datasheets

Figure 1-2. PSoC Creator Features

PSoC Creator also enables you to tap into an entire tool ecosystem with integrated compiler chains

and production programming programmers for PSoC devices.

For more information, visit www.cypress.com/psoccreator. Visit PSoC Creator training page for video

tutorials on learning and using PSoC Creator.

CY8CKIT-043 PSoC® 4 M-Series Prototyping Kit Guide, Doc. #: 001-97606 Rev. ** 9

Introduction

1.2.1 PSoC Creator Code Examples

PSoC Creator includes a large number of code examples. These examples are available from the

PSoC Creator Start Page, as Figure 1-3 shows.

Code examples can speed up your design process by starting you off with a complete design,

instead of a blank page. The code examples also show how PSoC Creator Components can be

used for various applications. Code examples and documentation are included, as shown in

Figure 1-4 on page 10.

In the Find Example Project dialog shown in Figure 1-4, you have several options:

■Filter for examples based on architecture or device family, that is, PSoC 3, PSoC 4, or

PSoC 5LP; project name; or keyword.

■Select from the menu of examples offered based on the Filter Options.

■Review the example project’s description (on the Documentation tab).

■Review the code from the Sample Code tab. You can copy the code from this window and paste

to your project, which can help speed up code development.

■Create a new project (and a new workspace if needed) based on the selection. This can speed

up your design process by starting you off with a complete, basic design. You can then adapt that

design to your application.

Figure 1-3. Code Examples in PSoC Creator

CY8CKIT-043 PSoC® 4 M-Series Prototyping Kit Guide, Doc. #: 001-97606 Rev. ** 10

Introduction

Figure 1-4. Code Example Projects with Sample Code

1.2.2 Kit Code Example

In addition to the examples built into PSoC Creator, this kit includes a simple example, which can be

used to quickly evaluate the functionality of this kit. The example is described in the Code

Examples chapter on page 33. In addition, the chapter also includes a section explaining how to use

PSoC Creator code examples with the kit by taking one example.

1.2.3 PSoC Creator Help

Visit the PSoC Creator home page to download the latest version of PSoC Creator. Then, launch

PSoC Creator and navigate to the following items:

■Quick Start Guide: Choose Help > Documentation > Quick Start Guide. This guide gives you

the basics for developing PSoC Creator projects.

■Simple Component example projects: Choose File > Example project.... These example

projects demonstrate how to configure and use PSoC Creator Components.

■Starter designs: Choose File > New > Project > PSoC 4100M / PSoC 4200M Starter Designs.

These starter designs demonstrate the unique features of the PSoC 4 M-Series.

■System Reference Guide: Choose Help > System Reference Guides. This guide lists and

describes the system functions provided by PSoC Creator.

■Component datasheets: Right-click a Component and select Open Datasheet, as shown in

Figure 1-5 on page 11. Visit the PSoC 4 Component Datasheets page for a list of all PSoC 4

Component datasheets.

■Document Manager: PSoC Creator provides a document manager to help you to easily find and

review document resources. To open the document manager, choose the menu item Help >

Document Manager.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cypress Mikrocontroller Handbücher

Cypress

Cypress Perform PSOC 5LP PROTOTYPING KIT Bedienungsanleitung

Cypress

Cypress PSOC 3 FIRSTTOUCH STARTER KIT Bedienungsanleitung

Cypress

Cypress CY8CKIT-001 Handbuch

Cypress

Cypress CY3250-PLC20QFN Bedienungsanleitung

Cypress

Cypress FM0+ S6E1C-Series Bedienungsanleitung

Cypress

Cypress CY3668 Bedienungsanleitung

Cypress

Cypress FR Series Bedienungsanleitung

Cypress

Cypress PSoC CY8CKIT-048 Bedienungsanleitung

Cypress

Cypress PSoC CY8CPROTO-062-4343W Bedienungsanleitung

Cypress

Cypress MB2146-301A-E Bedienungsanleitung

Cypress

Cypress CY8CKIT-147 Handbuch

Cypress

Cypress FR81S CY91F52 Series Betriebsanleitung

Cypress

Cypress Traveo II Bedienungsanleitung

Cypress

Cypress CE219490 Bedienungsanleitung

Cypress

Cypress EZ-USB FX3 CYUSB3KIT-003 Bedienungsanleitung

Cypress

Cypress SPANSION FM4 MB9BF568 Series Bedienungsanleitung

Cypress

Cypress CY3652 Bedienungsanleitung

Cypress

Cypress CY3276 Bedienungsanleitung

Cypress

Cypress PSoC 3 Bedienungsanleitung

Cypress

Cypress CY14NVSRAMKIT-001 Bedienungsanleitung

Cypress

Cypress MB95310L Series Bedienungsanleitung

Cypress

Cypress CY8CKIT-062-BLE Bedienungsanleitung

Cypress

Cypress S6E2DH series Bedienungsanleitung

Cypress

Cypress CY4531 EZ-PD CCG3 EVK Bedienungsanleitung

Beliebte Mikrocontroller Handbücher anderer Marken

AMS

AMS AS7261 Demo Kit Bedienungsanleitung

Novatek

Novatek NT6861 Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266 SDK Einrichtungshandbuch

Nuvoton

Nuvoton ISD61S00 ChipCorder Leitfaden

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Bedienungsanleitung

Texas Instruments

Texas Instruments Chipcon CC2420DK Bedienungsanleitung

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Bedienungsanleitung

NEC

NEC 78GK0S/K 1+ Series Montage- und Bedienungsanleitung

Mikroe

Mikroe SEMITECH N-PLC Click Montage- und Bedienungsanleitung

Intel

Intel Agilex Bedienungsanleitung

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Bedienungsanleitung

Texas Instruments

Texas Instruments TMS320F2837 D Series Bedienungsanleitung

CYPRES

CYPRES CY14NVSRAMKIT-001 Bedienungsanleitung

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266EX Betriebsanleitung

Abov

Abov AC33M8128L Bedienungsanleitung

Laird

Laird BL654PA Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories C8051F800 Bedienungsanleitung