D-Link DBG-X1000 Bedienungsanleitung

This document will guide you through the

basic installation process for your new

D-Link Nuclias Cloud-Managed Wireless

VPN Gateway

DBG-X1000

Quick Installation Guide

2 D-Link Nuclias Cloud-Managed Wireless VPN Gateway

ENGLISH

About This Guide

This guide gives step by step instructions for

setting up D-Link DBG-X1000. Please note that

the model you have purchased may appear

slightly di󰀨erent from those shown in the illustra-

tions.

Item Feature Description

A LED

(Top to bottom)

Power LED: Indicates the device is

powered on.

B USB Port (1) It can support various USB 2.0, 3.0

devices below:

1.Flash Disk or Hard Disk for

network sharing.

2.Printer (It will be supported by

future rmware upgrade)

C Gigabit LAN port

(1-4)

Connect Ethernet devices, such as

computers, switches and hubs.

D Gigabit WAN

port (1)

One auto MDI/MDIX WAN ports

are the connection for the Ethernet

cable to the cable or DSL modem.

E Console Port (1) Used to access Command Line

Interface (CLI) via RJ45-to-DB9

console Cable.

Table 1: DBG-X1000 Front Panel Descriptions

Device Status LEDs and Ethernet Port LEDs

The device LEDs show information about current

device status. When the device power up, the

POWER/STATUS LED will show solid orange

during power on process. Startup takes one minute

approximately to complete, the LED will change

to solid green. If you want to turn the device o󰀨

and on again, we recommend you wait a few

seconds between shutting it down and powering it

back. The Ethernet LEDs show the status of each

Ethernet port. Table 2 lists the name, color, status

and description of each device LED.

Figure 2. Ethernet RJ-45 Port LEDs

TX/RX

Status

Link

Speed

Unpacking the Product

Open the shipping carton and carefully unpack its

contents. Please consult the packing list located

in following information to make sure all items are

present and undamaged. If any item is missing

or damaged, please contact your local D-Link

reseller for replacement.

- One (1) DBG-X1000 One (1) 12V/2A Power

Adapter

- One (1) Console Cable (RJ45-to-DB9 Cable)

- One (1) Ethernet (CAT5 UTP/Straight Through)

Cable

- Four (4) Rubber foot

- Two (2) Antenna

Product Overview

This chapter provides detailed descriptions of the

DBG-X1000 device and its components.

LED

Indicators

Color Status Description

Power Orange/

Green

Solid

Orange

Device during power-on

process

Solid Green Completion of power on

Light O󰀨 The device is power-o󰀨

Cloud Orange/

Green

Solid

Orange

Cloud Connecting

Solid Green Cloud Connected

TX/RX

Status

Green Light O󰀨 No Link.

Solid Green Link present.

Blinking

Green

Port is sending or

receiving data.

LINK

Speed

Green/

Orange

Light O󰀨 Port is operating at

10Mbps.

Solid Green Port is operating at

100Mbps

Solid

Orange

Port is operating at

1000Mbps

Table 2: Device Status LED Descriptions

Front Panel

Figure 1. DBG-X1000 Front Panel

A C ED B

D-Link Nuclias Cloud-Managed Wireless VPN Gateway 3

ENGLISH

Connecting Power and Turn the Device

On/O󰀨

Installing and Connecting the

Device

This chapter describes how to connect cables and

power to the device.

Before You Begin

Observe the following precautions to help prevent

shutdowns, equipment failures and injuries:

- Before installation, always check that the power

supply is disconnected

- Ensure that the room in which you operate the

device has adequate air circulation and that

the room temperature does Not exceed 40˚C

(104˚F)

- Allow 1 meter (3 feet) of clear space to the front

and back of the device.

- Do not place the device in an equipment rack

frame that blocks the air vents on the sides of

the chassis. Ensure that enclosed racks have

fans and louvered sides.

- Correct these hazardous conditions before

any installation: moist or wet oors, leaks,

ungrounded or frayed power cables, or missing

safety grounds.

The AC/DC Power Adapter shipped with the

device connects the device to earth ground when

plugged an AC grounding-type power outlet. The

device must be connected to earth ground during

normal operation.

To connect power to the device, plug the AC/DC

power adapter into the DC power phone jet on the

DBG-X1000 Default Interface Settings

Ethernet

Interface

Type IP Address

Web-Based

Management

DHCP

Client

LAN(1-4) /

WLAN

Static IP 192.168.10.1 Enabled Enabled

WAN DHCP

Client

0.0.0.0 Disabled Disabled

Table 3: Default Interface Settings

Note: DBG-X1000 allows Web GUI access

from LAN and Wireless interfaces by default for

security reason.

back panel of the device.

Note: We recommend using a surge protector for

the power connection.

To power on the DBG-X1000 device, press the

DC power switch on the rear panel to the on

position. To power o󰀨 the device, press the power

switch to the o󰀨 position.

Connecting the Device to a Network

This section provides basic information about

physically connecting the DBG-X1000 to a

network. To connect the necessary cables as

shown in Figure 3.

1. Connect an RJ-45 cable from the port labeled

WAN to the external router. The port WAN is

pre-allocated to the WAN network segment.

2. Connect an RJ-45 cable from the port labeled

LAN (1-8) to a switch in the LAN network

segment.

3. Connect an RJ45-to-DB9 cable from the

console port for CLI (Command Line Interface)

management access.

Figure 3. Basic Cabling Example

WAN

LAN Console

Internet

Switch

User

4 D-Link Nuclias Cloud-Managed Wireless VPN Gateway

ENGLISH

The DBG-X1000 provides an serial port that

enables a connection to a computer or terminal

for monitoring and conguring the device. This

port is a RJ-45 connector, implemented as a

data communication terminal equipment (DCE)

connection.

To use the console port connection, you need the

following equipment:

1. A terminal or a computer with both a serial port

and the ability to emulate a terminal.

2. A RJ45-to-DB9 RS-232 with female connector.

(Already included in packing list)

3. If your Laptop or PC doesn’t have RS-232

connector, a converter is required.

Note: DBG-X1000 does not come with RS-232

converter and these must be purchased separately.

To establish a console connection:

1. Plug the RJ-45 connector of the supplied

RJ45-to-DB9 cable directly to the console port

on the device.

2. Connect the other end of the cable to a terminal

or to the serial connector of a computer

running terminal emulation software. Set the

terminal emulation software as following:

Baud rate: 115200

Data bits: 8

Parity: None

Stop bits: 1

Flow control: None

3. When you have correctly set up the terminal,

having previously followed the instructions

in section “Connecting Power and Turn the

Device On/O󰀨” then switch on your device.

The boot sequence appears in the terminal.

4. Once the boot sequence completes, the

command prompt is displayed, the device is

ready to be congured.

Using a Console Connection

(RJ45-to-DB9 DCE)

To access the device with the WebUI:

1. Connect your workstation on the port labeled

LAN (1-4), which is pre-allocated to the LAN.

2. Ensure your workstation is DHCP Client

enabled or congured with a static IP address

in the 192.168.10.0/24 subnet.

3. Log on the device web interface the default log

on information is:

Username: admin

Password: admin

Using the WebUI

To use the WebUI, the workstation from which you

are managing the device must initially be on the

same subnetwork as the device.

Figure 4. Authentication Message

Technical Support

https://www.dlink.com/support

Initially Congure the Device

The software is preinstalled on the DBG-X1000

device. When the device is powered on, it is ready

to be congured. While the device has a default

factory conguration that allow you to initially

connect to the device, you must perform further

conguration for your specic network require-

ments.

D-Link Nuclias Cloud-Managed Wireless VPN Gateway 5

Federal Communication Commission Interference Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment o󰀨 and on, the user is encouraged to try to correct the inter-

ference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit di󰀨erent from that to which the receiver is

connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modications not expressly approved by the party responsible for

compliance could void the user's authority to operate this equipment.

Operations in the 5.15-5.25GHz band are restricted to indoor usage only.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Note: The country code selection is for non-US model only and is not available to all US model. Per FCC

regulation, all WiFi product marketed in US must xed to US operation channels only.

Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with minimum distance 20cm between the radiator &

your body.

Industry Canada statement

This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following two condi-

tions: (1) This device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio exempts de licence.

L’exploitation est autorisée aux deux conditions suivantes : (1) le dispositif ne doit pas produire de

brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage

susceptible de provoquer un fonctionnement indésirable.

6 D-Link Nuclias Cloud-Managed Wireless VPN Gateway

Caution :

(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for

harmful interference to co-channel mobile satellite systems;

(ii) for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band

5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits as appropriate;

(iii) where applicable, antenna type(s), antenna models(s), and worst-case tilt angle(s) necessary to

remain compliant with the e.i.r.p. elevation mask requirement set forth in section 6.2.2.3 shall be clearly

indicated.

Avertissement:

(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utili-

sation à l’intérieur an de réduire les risques de brouillage préjudiciable aux systèmes de satellites

mobiles utilisant les mêmes canaux;

(ii) pour les dispositifs munis d’antennes amovibles, le gain maximal d’antenne permis (pour les dispositifs

utilisant la bande de 5 725 à 5 850 MHz) doit être conforme à la limite de la p.i.r.e. spéciée, selon le cas;

(iii) lorsqu’il y a lieu, les types d’antennes (s’il y en a plusieurs), les numéros de modèle de l’antenne et

les pires angles d’inclinaison nécessaires pour rester conforme à l’exigence de la p.i.r.e. applicable au

masque d’élévation, énoncée à la section 6.2.2.3, doivent être clairement indiqués.

Radiation Exposure Statement:

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with greater than 25cm between the radiator & your

body.

Déclaration d'exposition aux radiations:

Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies pour un

environnement non contrôlé. Cet équipement doit être installé et utilisé à plus de 25 cm entre le radiateur

et votre corps.

D-Link Nuclias Cloud-Managed Wireless VPN Gateway 7

Ver. 1.00

2021/09/17

Inhaltsverzeichnis

Andere D-Link Tor Handbücher

D-Link

D-Link DSA-3600 Bedienungsanleitung

D-Link

D-Link DSH-G300 Bedienungsanleitung

D-Link

D-Link DG-102S Bedienungsanleitung

D-Link

D-Link DSA-3600 Bedienungsanleitung

D-Link

D-Link Airspot DSA-3100 Bedienungsanleitung

D-Link

D-Link DG-104S Bedienungsanleitung

D-Link

D-Link DFL-M510 Bedienungsanleitung

D-Link

D-Link DG-104SH Bedienungsanleitung

D-Link

D-Link DSA 5100 - Airspot - Gateway Bedienungsanleitung

D-Link

D-Link DVG-4088S Bedienungsanleitung

D-Link

D-Link DSA 5100 - Airspot - Gateway Bedienungsanleitung

D-Link

D-Link DVG-7022S Bedienungsanleitung

D-Link

D-Link DPN-1021G Bedienungsanleitung

D-Link

D-Link DVG-2016 Bedienungsanleitung

D-Link

D-Link DRO-220i Bedienungsanleitung

D-Link

D-Link DG-104S Bedienungsanleitung

D-Link

D-Link DSA 5100 - Airspot - Gateway Bedienungsanleitung

D-Link

D-Link DG-102SH Bedienungsanleitung

D-Link

D-Link Airspot DSA-3100 Bedienungsanleitung

D-Link

D-Link DPN-144DG Bedienungsanleitung

D-Link

D-Link DSL-604+ Bedienungsanleitung

D-Link

D-Link Verizon DSL-2750B Bedienungsanleitung

D-Link

D-Link DG-102SP Bedienungsanleitung

D-Link

D-Link DVG-3104MS - VoiceCenter PSTN Gateway Bedienungsanleitung

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

RTA

RTA 460A-NNA4 Technisches Datenblatt

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

NETGEAR

NETGEAR C6300BD Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

HMS

HMS Netbiter EasyConnect EC150 Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung