D-Link DGS-1016D - Switch Bedienungsanleitung

D-Link®DGS-1016D

DGS-1024D

16/24-Port 10/100/1000Mbps

Gigabit Ethernet Switch

Manual

Building Networks for People

RECYCLABLE

(March 2012)

D-Link DGS-1016D/DGS-1024D Unmanaged Gigabit Ethernet Switch

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of D-Link Corporation is

strictly forbidden.

Trademarks used in this text: D-Link and the D-LINK logo are trademarks of D-Link Corporation;

Microsoft and Windows are registered trademarks of Microsoft Corporation.

Other trademarks and trade names may be used in this document to refer to either the entities

claiming the marks and names or their products. D-Link Corporation disclaims any proprietary

interest in trademarks and trade names other than its own.

FCC Warning

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with this user’s guide, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own

expense.

CE Mark Warning

This is a Class A product. In a domestic environment, this product may cause radio interference

in which case the user may be required to take adequate measures.

Warnung!

Dies ist ein Produkt der Klasse A. Im Wohnbereich kann dieses Produkt Funkstoerungen

verursachen. In diesem Fall kann vom Benutzer verlangt werden, angemessene Massnahmen

zu ergreifen.

Precaución!

Este es un producto de Clase A. En un entorno doméstico, puede causar interferencias de radio,

en cuyo case, puede requerirse al usuario para que adopte las medidas adecuadas.

Attention!

Ceci est un produit de classe A. Dans un environnement domestique, ce produit pourrait causer

des interférences radio, auquel cas l`utilisateur devrait prendre les mesures adéquates.

Attenzione!

Il presente prodotto appartiene alla classe A. Se utilizzato in ambiente domestico il prodotto può

causare interferenze radio, nel cui caso è possibile che l`utente debba assumere provvedimenti

adeguati.

VCCI Warning

警告使用者：

這是甲類的資訊產品，在居住的環境中使用時，可能會造成射頻干擾，在這種情況下，使用者會

被要求採取某些適當的對策。

iii

CONTENTS

PREFACE………………………………………………….……………IV

NOTES,NOTICES,AND CAUTIONS ............................................................IV

SAFETY INSTRUCTIONS..............................................................................V

General Precautions for Rack-Mountable Products.........................vii

Protecting Against Electrostatic Discharge ......................................ix

INTRODUCTION…………………………………………………….…1

SWITCH DESCRIPTION ...............................................................................1

Switch Features ..................................................................................2

Gigabit Ethernet Technology..............................................................3

802.1p and QoS ..................................................................................3

D-LINK GREEN TECHNOLOGY..................................................................5

FRONT-PANEL COMPONENTS....................................................................6

LED Indicators ...................................................................................6

Cable Diagnostics.............................................................................16

POWER INPUT ON REAR PANEL...............................................................10

INSTALLATION………………………………………………….…….12

Package Contents .............................................................................12

BEFORE YOU CONNECT TO THE NETWORK............................................13

Mounting the Switch on a Rack ........................................................14

Attaching the Rubber Feet................................................................15

Provide for Adequate Ventilation .....................................................15

POWER ON...............................................................................................16

Power Failure...................................................................................16

CONNECTING THE SWITCH………………………………………..17

Connect to an End Node...................................................................18

Connect to Hub or Switch.................................................................19

Connect to Network Backbone or Server..........................................20

TECHNICAL SPECIFICATIONS…………………………………….21

GLOSSARY………………………………………………………………24

D-Link DGS-1016D/DGS-1024D Unmanaged Gigabit Ethernet Switch

Preface

The DGS-1016D/DGS-1024D Manual is divided into sections that describe the

system installation and operating instructions with examples.

Section 1, Introduction - A description of the physical features of the Switch,

including LED indicators, ports and panel descriptions.

Section 2, Installation – A description of the physical installation of the Switch,

mounting the Switch in a equipment rack and powering on the Switch.

Section 3, Connecting the Switch – A description of how to connect your

Switch to an end node, hub, another switch or backbone server.

Appendix Technical Specifications - The technical specifications of the

DGS-1016D/DGS-1024D.

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information

that helps you make better use of your device.

NOTICE: A NOTICE indicates either potential

damage to hardware or loss of data and tells you

how to avoid the problem.

CAUTION: A CAUTION indicates the potential for

property damage, personal injury or death.

D-Link DGS-1016D/DGS-1024D Unmanaged Gigabit Ethernet Switch

Safety Instructions

Use the following safety guidelines to ensure your own personal safety and to help protect your

system from potential damage. Throughout this safety section, the caution icon ( ) is used to

indicate cautions and precautions that you need to review and follow.

Safety Cautions

To reduce the risk of bodily injury, electrical shock, fire, and damage to the

equipment, observe the following precautions.

Observe and follow service markings. Do not service any product except as

explained in your system documentation. Opening or removing covers that are

marked with the triangular symbol with a lightning bolt may expose you to an

electrical shock. Only a trained service technician should service components inside

these compartments.

If any of the following conditions occur, unplug the product from the electrical outlet

and replace the part or contact your trained service provider:

– The power cable, extension cable, or plug is damaged.

– An object has fallen into the product.

– The product has been exposed to water.

– The product has been dropped or damaged.

– The product does not operate correctly when you follow the operating

instructions.

•Keep your system away from radiators and heat sources. Also, do not block

cooling vents.

•Do not place any device on top of Switch, or place the Switch on top of any

device or object that will block the free flow of air through the ventilation slots on

the sides, top, and bottom of the Switch’s case.

•Keep your hand away from top and bottom of device that generates a

significant amount of heat.

•Do not spill food or liquids on your system components, and never operate the

product in a wet environment. If the system gets wet, see the appropriate

section in your troubleshooting guide or contact your trained service provider.

•Do not push any objects into the openings of your system. Doing so can cause

a fire or an electric shock by shorting out interior components.

•Use the product only with approved equipment.

•Allow the product to cool before removing covers or touching internal

components.

•Operate the product only from the type of external power source indicated on

the electrical ratings label. If you are not sure of the type of power source

required, consult your service provider or local power company.

D-Link DGS-1016D/DGS-1024D Unmanaged Gigabit Ethernet Switch

Safety Instructions (continued)

•To help avoid damaging your system, be sure the voltage selection Switch (if

provided) on the power supply is set to match the power available at your

location:

– 115 volts (V)/60 hertz (Hz) in most of North and South America and

some Far Eastern countries such as South Korea and Taiwan

– 100 V/50 Hz in eastern Japan and 100 V/60 Hz in western Japan.

– 230 V/50 Hz in most of Europe, the Middle East, and the Far East.

•Also be sure that attached devices are electrically rated to operate with the

power available in your location.

•Use only approved power cable(s). If you have not been provided with a power

cable for your system or for any AC-powered option intended for your system,

purchase a power cable that is approved for use in your country. The power

cable must be rated for the product and for the voltage and current marked on

the product's electrical ratings label. The voltage and current rating of the cable

should be greater than the ratings marked on the product.

•To help prevent an electric shock, plug the system and peripheral power cables

into properly grounded electrical outlets. These cables are equipped with three-

prong plugs to help ensure proper grounding. Do not use adapter plugs or

remove the grounding prong from a cable. If you must use an extension cable,

use a 3-wire cable with properly grounded plugs.

•Observe extension cable and power strip ratings. Make sure that the total

ampere rating of all products plugged into the extension cable or power strip

does not exceed 80 percent of the ampere ratings limit for the extension cable

or power strip.

•To help protect your system from sudden, transient increases and decreases in

electrical power, use a surge suppressor, line conditioner, or uninterruptible

power supply (UPS).

•Position system cables and power cables carefully; route cables so that they

cannot be stepped on or tripped over. Be sure that nothing rests on any cables.

•Do not modify power cables or plugs. Consult a licensed electrician or your

power company for site modifications. Always follow your local/national wiring

rules.

•When connecting or disconnecting power to hot-pluggable power supplies, if

offered with your system, observe the following guidelines:

– Install the power supply before connecting the power cable to the power

supply.

– Unplug the power cable before removing the power supply.

– If the system has multiple sources of power, disconnect power from the

system by unplugging all power cables from the power supplies.

•Move products with care; ensure that all casters and/or stabilizers are firmly

connected to the system. Avoid sudden stops and uneven surfaces.

D-Link DGS-1016D/DGS-1024D Unmanaged Gigabit Ethernet Switch

vii

Safety Instructions (continued)

General Precautions for Rack-

Mountable Products

•Observe the following precautions for rack stability and safety. Also refer to the

rack installation documentation accompanying the system and the rack for

specific caution statements and procedures.

•Systems are considered to be components in a rack. Thus, "component" refers

to any system as well as to various peripherals or supporting hardware.

CAUTION: Installing systems in a rack without the front

and side stabilizers installed could cause the rack to tip

over, potentially resulting in bodily injury under certain

circumstances. Therefore, always install the stabilizers

before installing components in the rack.

After installing system/components in a rack, never pull

more than one component out of the rack on its slide

assemblies at one time. The weight of more than one

extended component could cause the rack to tip over

and may result in serious injury.

•Before working on the rack, make sure that the stabilizers are secured to the

rack, extended to the floor, and that the full weight of the rack rests on the floor.

Install front and side stabilizers on a single rack or front stabilizers for joined

multiple racks before working on the rack.

D-Link DGS-1016D/DGS-1024D Unmanaged Gigabit Ethernet Switch

viii

Safety Instructions (continued)

•Always load the rack from the bottom up, and load the heaviest item in the rack

first.

•Make sure that the rack is level and stable before extending a component from

the rack.

•Use caution when pressing the component rail release latches and sliding a

component into or out of a rack; the slide rails can pinch your fingers.

•After a component is inserted into the rack, carefully extend the rail into a locking

position, and then slide the component into the rack.

•Do not overload the AC supply branch circuit that provides power to the rack.

The total rack load should not exceed 80 percent of the branch circuit rating.

•Ensure that proper airflow is provided to components in the rack.

•Do not step on or stand on any component when servicing other components in

a rack.

CAUTION: Never defeat the ground conductor or

operate the equipment in the absence of a suitably

installed ground conductor. Contact the appropriate

electrical inspection authority or an electrician if you are

uncertain that suitable grounding is available.

CAUTION: The system chassis must be positively

grounded to the rack cabinet frame. Do not attempt to

connect power to the system until grounding cables are

connected. Completed power and safety ground wiring

must be inspected by a qualified electrical inspector.

An energy hazard will exist if the safety ground cable is

omitted or disconnected.

D-Link DGS-1016D/DGS-1024D Unmanaged Gigabit Ethernet Switch

Protecting Against Electrostatic Discharge

Static electricity can harm delicate components inside your system. To prevent static

damage, discharge static electricity from your body before you touch any of the

electronic components, such as the microprocessor. You can do so by periodically

touching an unpainted metal surface on the chassis.

You can also take the following steps to prevent damage from electrostatic

discharge (ESD):

1. When unpacking a static-sensitive component from its shipping carton, do

not remove the component from the antistatic packing material until you

are ready to install the component in your system. Just before unwrapping

the antistatic packaging, be sure to discharge static electricity from your

body.

2. When transporting a sensitive component, first place it in an antistatic

container or packaging.

3. Handle all sensitive components in a static-safe area. If possible, use

antistatic floor pads, workbench pads, and an antistatic grounding strap.

SECTION 1

Introduction

Switch Description

Switch Features

D-Link Green Technology

Ports

Front-Panel Components

LED Indicators

Power Input on Rear Panel

Switch Description

The 16-port DGS-1016D and 24-port DGS-1024D Switches provide

dedicated 10, 100 or 1000 Mbps Ethernet bandwidth on each port.

The ports will automatically detect the speed, duplex and MDI/MDIX

status of the device it is connecting to, and adjust these settings

accordingly. The Switch ports can be used to network computers,

printers, servers, routers, other switches or any device equipped

with an Ethernet port. For best performance, use Category 5 or

better Ethernet cabling.

This stand alone Switch is very easy to set up. There is no network

management is required; simply power on the Switch and connect

the cables.

However, please keep in mind that the standard rules of available

Ethernet cable length from one device to another which cannot

exceed 100 meters (or 300 feet).

Andere Handbücher für DGS-1016D - Switch

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere D-Link Netzwerk-Router Handbücher

D-Link

D-Link DSL-2600U/NRU Bedienungsanleitung

D-Link

D-Link DIR-610N+ Bedienungsanleitung

D-Link

D-Link EBR-2310 - EN Broadband Router Bedienungsanleitung

D-Link

D-Link DIR-X1530 Bedienungsanleitung

D-Link

D-Link DSL-2750U Bedienungsanleitung

D-Link

D-Link DSL-1500G Bedienungsanleitung

D-Link

D-Link DSR-250V2 Bedienungsanleitung

D-Link

D-Link 502G - DSL Router - EN Bedienungsanleitung

D-Link

D-Link DWR-555 Bedienungsanleitung

D-Link

D-Link DIR-130 - Broadband VPN Router Einrichtungshandbuch

D-Link

D-Link DIR-636L Bedienungsanleitung

D-Link

D-Link DSL-2751 Bedienungsanleitung

D-Link

D-Link DIR-140L Bedienungsanleitung

D-Link

D-Link DSL-2650NRU Bedienungsanleitung

D-Link

D-Link DI-106 Series Bedienungsanleitung

D-Link

D-Link AC750 Bedienungsanleitung

D-Link

D-Link DSL-500 Bedienungsanleitung

D-Link

D-Link DIR-601 Bedienungsanleitung

D-Link

D-Link DSL-G804V Bedienungsanleitung

D-Link

D-Link DSL-G255 Bedienungsanleitung

D-Link

D-Link DIR-879 Bedienungsanleitung

D-Link

D-Link DSL-3580L Series Bedienungsanleitung

D-Link

D-Link DSL-514 Bedienungsanleitung

D-Link

D-Link DGS-3224SR Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise