D-Link DIS-300G Series Bedienungsanleitung

Quick Installation Guide

DIS-300G Series Managed Industrial Gigabit

Ethernet Switch

Quick Installation Guide

Overview

The Managed Ethernet Switch solutions are designed for supporting standard industrial

applications. Managed switches are easier to prioritize, partition, and organize user’s

network, providing a more reliable and better quality services.

Package Checklist

Please verify the box contains the followingitems:

Item Quantity

Management Ethernet switch 1

Wall-mount plates 2

DIN-Rail CLIP 1

M3 Screws (for the wall mount plates & DIN CLIP) 4

DC power terminal block 1

RJ45 Ethernet port Dust Cover Some

SFP Ethernet port Dust cover Same as SFP port number

Quick Installation Guide

Safety Instructions

When a fiber connection is removed during installation, testing, servicing or anactive fiber is

broken, ocular exposure to optical energy may be potentially hazardous, depending on the

laser output power.

The primary hazards of exposing laser radiation from an optical-fiber communication systems

are:

●

Damage to eyes from accidental exposure to a beam emitted by a laser source.

●

Damage to eyes from viewing the connector that attaches to a broken fiber or an

energized fiber.

If the equipment is used in a manner not speciﬁed by the manufacturer, the protection

provided by the equipment may be impaired.

DIN-Rail Mounting

Mounting steps:

1. Screw the din-clip with screws in the accessory kit.

2. Hook the unit onto the din-rail.

3. Push the bottom of the unit towards the din-rail until it locks in place.

Quick Installation Guide

Wall Mounting

Mounting steps:

1. Screw the wall-mount brackets with screws in the accessory kit.

< This graph is for all DIS-300G series >

Ethernet Interface (RJ45 Ethernet)

The switch provides two types of Ethernet interfaces: electrical (RJ45) and optical (SFP)

interfaces.

Connecting the Ethernet interface via RJ45:

●

To connect the switch to a PC, use straight-through or cross-over Ethernet cables,

●

To connect the switch to an Ethernet device, use UTP (Unshielded Twisted Pair)

or STP (Shielded Twisted Pair) Ethernet cables.

The pin assignment of RJ-45 connector is shown in the following figure and table.

Pin Assignment

PoE Assignment

(for DIS-300G-8PSW/DIS-300G-

14PSW only)

1,2 T/Rx+,T/Rx- Positive VPort

3,6 T/Rx+,T/Rx- Negative VPort

4,5 T/Rx+,T/Rx- X

7,8 T/Rx+,T/Rx- X

Quick Installation Guide

Ethernet Interface (Fiber, SFP)

For both 100/1000 Mbps fiber speed connections, the SFP slots are available. The SFP slot

accepts the fiber transceivers that typically have an LC connector.

The fiber transceivers have options of multimode, single mode, long-haul or special-

application transceivers.

DANGER:

Never attempt to view optical connectors that might be emitting laser energy.

Do not power up the laser product without connecting the laser to the optical

fiber and putting the dust cover in position, as laser outputs will emit infrared

laser light at this point.

Connecting Power Terminal Block

The switch can be powered from two power supplies (input range 12V – 58V). Insert

the positive and negative wires into V+ and V- contacts on the terminal block

respectively and tightenthe wire-clamp screws to prevent the wires from being

loosened.

Note:

The DC power should be connected to a well-fused power supply.

DIS-300G12SW

Quick Installation Guide

DIS-300G-8PSW/DIS-300G-14PSW

Alarm Relay and Ground

The alarm relay output contacts are in the middle of the DC terminal block connector as

shown in the figure below.

The alarm relay out is “Normal Open”, and it will be closed when detected any predefined

failure such as power failures or Ethernet link failures.

The relay output with current carrying capacity of 0.5A @ 24 VDC

Quick Installation Guide

Console Connection

The Console port is for local management by using a terminal emulator or a computerwith

terminal emulation software.

●

DB9 connector connect to computer COM port

●

Baud rate: 115200bps

●

8 data bits, 1 stop bit

●

None Priority

●

None flow control

To connect the host PC to the console port, a RJ45 (male) connector-to-RS232 DB9

(female) connector cable is required. The RJ45 connector of the cable is connected to the

CID port of the switch; the DB9 connector of the cable is connected to the PC COM port.

The pin assignment of the console cable is shown below:

Quick Installation Guide

Connect & Login to Managed Switch

1. Connecting to the Ethernet port (RJ45 Ethernet port) of Managed Switch.

2. Factory default IP: 10.90.90.90

3. Login with default account and password.

Username: admin

Password: admin

CLI Initialization & Configuration

1. Connecting to the Ethernet port(RJ45 Ethernet port) of Managed Switch

2. Key-in the command under Telnet: telnet 10.90.90.90

3. Login with default account and password.

Username: admin

Password: admin

4. Change the IP with commands listed below:

CLI Command:

enable

configure

terminal

interface vlan 1

ip address xxx.xxx.xxx.xxx

xxx.xxx.xxx.xxx exit

Quick Installation Guide

LED STATUS INDICATIONS

LED Name Indicator /color Condition

P1/P2 On Green P1/P2 power line has power

Off P1/P2 power line disconnect or does not have power supplied

Alarm On Red Ethernet link fails, alarm or power failure alarmoccurs

Off No Ethernet link fails and no power failure alarm

Copper port

Link/Act

On Green Ethernet link up but no traffic isdetected

Flashing Green Ethernet link up and there is traffic detected

Off Ethernet link down

Copper port

Speed On Yellow A 1000Mbps connection is detected

Off No link, a 10Mbps or 100 Mbps connection is detected

SFP port

Link/Act On Green Ethernet link up

Off Ethernet link down

SFP port

Speed On Yellow SFP port speed 1000Mbps connection isdetected.

Off No link or a SFP port speed 100Mbps connection isdetected

DIS-300G-8PSW/DIS-300G-14PSW only

(Ring Role) On Green One of 3 Ring group is enabled and is Master role.

Off Ring is slave role

(Ring Status) On Green Ring fail happen and detected

Off No ring fail detected

PoE On Yellow PoE is detected

Off No link

Additional Information

You can refer to the user manual or visit http://support.dlink.com/ for more support.

Online Support

If there are any issues that are not in the user manual, please visit http://support.dlink.com/

which will direct you to your appropriate local D-Link support website.

Warranty Information

Visit http://warranty.dlink.com/ to view the D-Link Warranty information.

Ver. 1.00(EU)2017/12/04

Inhaltsverzeichnis

Andere D-Link Netzwerk-Router Handbücher

D-Link

D-Link DIR-640L Bedienungsanleitung

D-Link

D-Link DSL-2640B Bedienungsanleitung

D-Link

D-Link DIR-806A Bedienungsanleitung

D-Link

D-Link DIR-827 Bedienungsanleitung

D-Link

D-Link COVR- C1203 Bedienungsanleitung

D-Link

D-Link Express Ethernetwork DI-704P Bedienungsanleitung

D-Link

D-Link Cobra DSL-5300 Bedienungsanleitung

D-Link

D-Link DIR-X5460 Bedienungsanleitung

D-Link

D-Link DIR-605 Bedienungsanleitung

D-Link

D-Link DSL-502T Bedienungsanleitung

D-Link

D-Link DSL-2730B Montageanleitung

D-Link

D-Link DSL-226 Bedienungsanleitung

D-Link

D-Link DES-1316K Bedienungsanleitung

D-Link

D-Link DIR-615S/A1 Bedienungsanleitung

D-Link

D-Link xStack DGS-3426G Bedienungsanleitung

D-Link

D-Link DIR-808L Bedienungsanleitung

D-Link

D-Link DSL-G804V Bedienungsanleitung

D-Link

D-Link DWR-953 Bedienungsanleitung

D-Link

D-Link AirPlus XtremeG Ethernet-to-Wireless Bridge... Bedienungsanleitung

D-Link

D-Link DWR-932 Bedienungsanleitung

D-Link

D-Link COVR-C1202 Bedienungsanleitung

D-Link

D-Link DSL-2500U Bedienungsanleitung

D-Link

D-Link DES-6300 Bedienungsanleitung

D-Link

D-Link DSS-8+ Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung