D-Link DSL-504T Bedienungsanleitung
2
DSL-504T User’s Manual
D-Link Systems, Inc.
Table of Contents
Table of Contents
Table of Contents ...............................................................................................2
Package Contents ..............................................................................................4
Installation Overview ..........................................................................................5
Installation Requirements ..................................................................................6
Information you will need from your ADSL service provider ..............................8
Information you will need about your DSL-504T ADSL service router ...............9
Information you will need about your LAN or computer ..................................10
Introduction .....................................................................................................11
Features and Benefits .......................................................................................12
Standards Compatibility & Compliance ............................................................14
Front Panel Display ..........................................................................................16
Rear Panel Connections ...................................................................................17
Hardware Installation .......................................................................................18
Power ON Router .............................................................................................19
Network Connections ....................................................................................... 20
Basic Router Configuration ..............................................................................22
Access the Configuration Manager ..................................................................29
Login to the Home Page ...................................................................................30
Configure the Router ......................................................................................31
Using the Setup Wizard ....................................................................................33
Configuring the WAN connection ..................................................................... 46
LAN IP Settings ................................................................................................55
DHCP Server Settings ......................................................................................56
DNS Server Settings ........................................................................................58
3
DSL-504T User’s Manual
D-Link Systems, Inc.
Advanced Settings ...........................................................................................60
Tools ................................................................................................................72
Status ...............................................................................................................79
Multiple Virtual Connections ............................................................................83
Technical Specifications ...................................................................................85
Appendix A: IP Address Setup .........................................................................87
Appendix B: IP Concepts ..................................................................................90
Appendix C: Microfilters & Splitters ................................................................. 93
Contacting Technical Support ..........................................................................95
Warranty ..........................................................................................................96
Registration .....................................................................................................99
Table of Contents
4
DSL-504T User’s Manual
D-Link Systems, Inc.
Package Contents
Package Contents
D-Link DSL-504T
ADSL Ethernet Router
One twisted-pair telephone cable used for ADSL connection
One straight-through Ethernet cable
Manual on CD
Quick Installation Guide
One AC power adapter
If any of the above items are missing, please contact your reseller.
5
DSL-504T User’s Manual
D-Link Systems, Inc.
Installation Overview
The procedure to install the Router can be described in general terms in the following
steps:
1. Gather information and equipment needed to install the device. Before you
begin the actual installation make sure you have all the necessary information
and equipment.
2. Install the hardware, that is, connect the cables (Ethernet and telephone) to
the device and connect the power adapter.
3. Check the IP settings on your computer and change them if necessary so the
computer can access the web-based software built into the Router.
4. Use the web-based management software to configure the device to suit the
requirements of your ADSL account.
6
DSL-504T User’s Manual
D-Link Systems, Inc.
Installation Requirements
In order to establish a connection to the Internet it will be necessary to provide
information to the Router that will be stored in its memory. For some users, only
their account information (Username and Password) is required. For others, various
parameters that control and define the Internet connection will be required. You can
print out the two pages below and use the tables to list this information. This way you
have a hard copy of all the information needed to setup the Router. If it is necessary to
reconfigure the device, all the necessary information can be easily accessed. Be sure
to keep this information safe and private.
Low Pass Filters
Since ADSL and telephone services share the same copper wiring to carry their
respective signals, a filtering mechanism may be necessary to avoid mutual interference.
A low pass filter device can be installed for each telephone that shares the line with the
ADSL line. These filters are easy to install passive devices that connect to the ADSL
device and/or telephone using standard telephone cable. Ask your service provider for
more information about the use of low pass filters with your installation.
Operating Systems
The DSL-504T uses an HTML-based web interface for setup and management. The
web configuration manager may be accessed using any operating system capable
of running web browser software, including Windows 98 SE, Windows ME, Windows
2000, and Windows XP.
Web Browser
Any common Web browser can be used to configure the Router using the web
configuration management software. The program is designed to work best with more
recently released browsers such as Opera, Microsoft Internet Explorer® version 5.0,
Netscape Navigator® version 4.7, or later versions. The web browser must have
JavaScript enabled. JavaScript is enabled by default on many browsers. Make sure
JavaScript has not been disabled by other software (such as virus protection or web
user security packages) that may be running on your computer.
Ethernet Port (NIC Adapter)
Any computer that uses the router must be able to connect to it through the Ethernet
port on the Router. This connection is an Ethernet connection and therefore requires
that your computer be equipped with an Ethernet port as well. Most notebook computers
are now sold with an Ethernet port already installed. Likewise, most fully assembled
desktop computers come with an Ethernet NIC adapter as standard equipment. If your
computer does not have an Ethernet port, you must install an Ethernet NIC adapter
before you can use the Router. If you must install an adapter, follow the installation
instructions that come with the Ethernet NIC adapter.
7
DSL-504T User’s Manual
D-Link Systems, Inc.
Additional Software
It may be necessary to install software on your computer that enables the computer to
access the Internet. Additional software must be installed if you are using the device a
simple bridge. For a bridged connection, the information needed to make and maintain
the Internet connection is stored on another computer or gateway device, not in the
Router itself.
If your ADSL service is delivered through a Dynamic, PPPoE/PPPoA, Static, or Bridge
connection, the information needed to establish and maintain the Internet connection
can be stored in the Router. In this case, it is not necessary to install software on your
computer. It may however be necessary to change some settings in the device, including
account information used to identify and verify the connection.
All connections to the Internet require a unique global IP address. For bridged
connections, the global IP settings must reside in a TCP/IP enabled device on the LAN
side of the bridge, such as a PC, a server, a gateway device such as a router or similar
firewall hardware. The IP address can be assigned in a number of ways. Your network
service provider will give you instructions about any additional connection software or
NIC configuration that may be required.
8
DSL-504T User’s Manual
D-Link Systems, Inc.
Information you will need from your ADSL service provider
Username This is the Username used to log on to your ADSL service provider’s
network. It is commonly in the form - user@isp.com. Your ADSL service
provider uses this to identify your account.
Password This is the Password used, in conjunction with the Username above, to
log on to your ADSL service provider’s network. This is used to verify
the identity of your account.
Connection
Protocol This is the method your ADSL service provider uses to send and
receive data between the Internet and your computer. Your Modem
supports the following connection protocols: Dynamic, PPPoE/PPPoA,
Static, or Bridge.
Protocol This is the method your ADSL service provider will use to verify your
Username and Password when you log on to their network. Your
Modem supports the PAP and CHAP protocols.
VPI This is the Virtual Path Identifier (VPI). It is used in conjunction with the
Virtual Channel Identifier (VCI) below, to identify the data path between
your ADSL service provider’s network and your computer.
VCI This is the Virtual Channel Identifier (VCI). It is used in conjunction with
the VPI above to identify the data path between your ADSL service
9
DSL-504T User’s Manual
D-Link Systems, Inc.
Information you will need about your DSL-504T ADSL router
Username This is the Username needed access the Modem’s management
interface. When you attempt to connect to the device through a
web browser you will be prompted to enter this Username. The default
Username for the Modem is admin. This is a default setting and can
NOT be changed.
Password This is the Password you will be prompted to enter when you access
the Modem’s management interface. The default Password is admin.
This may be changed by the user.
LAN
Subnet
Mask for
the
This is the subnet mask used by the DSL-504T, and will be used
throughout your LAN. The default subnet mask is 255.255.255.0. This
can be changed later.
LAN IP
addresses
for the
DSL-504T
This is the IP address you will enter into the Address field of your web
browser to access the Modem’s configuration graphical user interface
(GUI) using a web browser. The default IP address is 192.168.1.1 and
it is referred to as the “Management IP” address in this User’s Manual.
This may be changed to suit any IP address scheme the user desires.
This address will be the base IP address used for DHCP service on
the LAN when DHCP is enabled.
10
DSL-504T User’s Manual
D-Link Systems, Inc.
Information you will need about your LAN or computer
Ethernet NIC If your computer has an Ethernet NIC, you can connect the
DSL-504T to this Ethernet port using an Ethernet cable. You can
also use the Ethernet port on the DSL-504T to connect to other
Ethernet devices, such as a Wireless Access Point.
DHCP Client
status Your DSL-504T ADSL Modem is configured, by default, to be
a DHCP server. This means that it can assign an IP address,
subnet mask, and a default gateway address to computers
on your LAN. The default range of IP addresses the DSL-
504T will assign are from 192.168.1.2 to 192.168.1.254. Your
computer (or computers) needs to be configured to Obtain an
IP address automatically (that is, they need to be configured as
It is recommended that your collect and record this information here, or in some other
secure place, in case you have to re-configure your ADSL connection in the future.
Once you have the above information, you are ready to setup and configure your
DSL-504T ADSL Router.
The Modem may be reset to its factory default settings by performing a
Restore settings operation within the management interface (see System
Commands). If you cannot gain access to the management interface, you
may opt to use the Reset button on the rear panel of the device).
Andere Handbücher für DSL-504T
9
Inhaltsverzeichnis
Andere D-Link Netzwerk-Router Handbücher
D-Link
D-Link R18 Bedienungsanleitung
D-Link
D-Link IR850LA1 Bedienungsanleitung
D-Link
D-Link DSL-2500U Bedienungsanleitung
D-Link
D-Link DSL-G604T Bedienungsanleitung
D-Link
D-Link DSL-502T Bedienungsanleitung
D-Link
D-Link DIR-815 Bedienungsanleitung
D-Link
D-Link DIR-300 - Wireless G Router Bedienungsanleitung
D-Link
D-Link DSL-526E Bedienungsanleitung
D-Link
D-Link DIR-853 Bedienungsanleitung
D-Link
D-Link DSS-24+ Bedienungsanleitung
D-Link
D-Link DSL-6740U Bedienungsanleitung
D-Link
D-Link Eagle Pro Al R12 Bedienungsanleitung
D-Link
D-Link DIR-822 Bedienungsanleitung
D-Link
D-Link DES-802 - Switch Bedienungsanleitung
D-Link
D-Link DIR-300S Bedienungsanleitung
D-Link
D-Link NetDefend DFL-260E Bedienungsanleitung
D-Link
D-Link myPocket DIR-457 Bedienungsanleitung
D-Link
D-Link DVA-5582 Bedienungsanleitung
D-Link
D-Link DWR-922 Bedienungsanleitung
D-Link
D-Link DSR-150 Bedienungsanleitung
Beliebte Netzwerk-Router Handbücher anderer Marken
NETGEAR
NETGEAR FS526T - Switch Bedienungsanleitung
Korenix
Korenix JetNet 5710G Series Bedienungsanleitung
Automated Logic
Automated Logic ZN551 Betriebsanleitung
Cisco
Cisco ASR 1000 Series Bedienerhandbuch
EnGenius
EnGenius ESR-9710 Bedienungsanleitung
Cisco
Cisco 805 Series Bedienungs- und Sicherheitshinweise