D-Link DES-7210-BASE Bedienungsanleitung

This document will guide you through the basic installation

process for your new D-Link chassis-based switch.

Building Networks for People

DES-7200

Documentation also available on

CD and via the D-Link Website

Quick Installation Guide

6/10 Slot Chassis-Based Switch

2D-Link 6/10 Slot Chassis-Based Switch

About This Guide

This guide contains step-by-step instructions

for setting up the D-Link DES-7200 Series

Switch Chassis. Please note that the model

you have purchased may appear slightly

different from those shown in the illustrations.

Please read this manual carefully before using

the product, paying special attention to safety

warnings so as to avoid injury or damage to

equipment.

This manual is intended for users who have

experience in installing and maintaining

network hardware, and assumes that users are

familiar with standard networking terms and

concepts.

Product Overview

D-Link’s DES-7200 series of chassis-based

switches are intelligent and high-performance

multi-layer LAN devices designed for enter-

prise campus and metropolitan area networks

(MAN). They are ideal for deployment in

environments where uninterrupted network

applications and a high level of performance,

security and control are required.

(GCVWTKPICƀGZKDNGOQFWNCTCTEJKVGEVWTGCPFindustry standard compliance, these switches

provide scalable expansion and a high level

of investment protection for businesses

and telecom carriers to deploy Gigabit and

10-Gigabit packet switching and routing for

QHſEGPGVYQTMKPICPF'VJGTPGVDCUGF+PVGTPGVservices to homes.

Power Supply Safety Warning

Ground the device before powering-

on to guard against power surges.

Be sure that all cables are-

grounded correctly.

Static Electricity Protection

Warning

Always wear an anti-static wrist-

strap when contacting the chassis

to prevent static damage.

Laser Safety Warning

CLASS 1 LASER PRODUCT

Directly looking at the optical- KPVGTHCEGQTQRVKECNſDGTUOC[ECWUGeye damage.

Serial Interface Safety Warning

Hot plugging a cable into the serial-

interface may damage the terminal.

Please power off the chassis before

connecting or disconnecting cables

to/from the serial interface.

Fan Safety Warning

The fan mechanism is dangerous.-

Avoid touching the area near the

fan.

Transportation Safety Warning

The device and components may-

comprise more than 80kg in total.

Do not use the handles on the rear-

of the device to carry the chassis.

Use care when inserting or-

removing heavy components.

Maintenance Warning

Maintenance should only be carried- QWVD[SWCNKſGFUGTXKEGVGEJPKEKCPUWarnings

6/10 Slot Chassis-Based Switch 3

Moving the Device

The DES-7200 is large and heavy. When

handling, please pay close attention to the

following guidelines:

Avoid moving the equipment frequently.-

At least two people are needed to move-

the equipment. Do not attempt to move the

equipment alone.

Turn off all power supplies and unplug all-

power cables before moving the equipment.

Use the side handles to remove all line cards,-

the fan tray, and the power module from the

chassis before moving.

Figure 1. Correctly Moving the DES-7200

WARNING:

Do not move the equipment by

grasping the panel, power supply

handle, or ventilation holes, as they

are not designed to bear weight.

Preparation For Installation

To ensure normal operation and prolonged

life of the DES-7200, the appropriate temper-

ature and humidity must be maintained in the

equipment room.

+HVJGGSWKROGPVTQQOJCUVGORGTCVWTGCPFhumidity that do not meet the requirements, the

equipment may sustain damage.

Temperature Relative Humidity

Long-term

Condition

Short-

term

Condition

Long-term

Condition

Short-

term

Condition

0°C-45°C 0°C-45°C 40%-65% 10%-90%

To prevent damage from static electricity,

please conform to the following guidelines:

Be sure to a adequately ground all1.

electronic equipment.

Use appropriate dust prevention measures.2.

Maintain the required humidity in the3.

operating environment.

Always wear an anti-static wrist strap when4.

working around any electronic circuitry.

Hold a circuit board by its edges. Do not5.

touch any components on the PCB.

Do not allow clothing to touch a circuit6.

board. An antistatic wrist strap can only

prevent static electricity from the human

body, but cannot mitigate static electricity

from clothing.

Static Discharge Damage Prevention

Table 1. Temperature and Humidity Requirements

Note:

The ambient temperature and1.

humidity should be measured

at the point that is 1.5m above

VJGƀQQTCPFODGHQTGVJGequipment when there is no

protective plate in front or back of

the equipment rack.

The short-term working condi-2.

tions apply where the continuous

working period does not exceed

48 hours and the cumulative total

period within a year does not

exceed 15 days.

System Grounding Requirements

Proper grounding will help to ensure stable and

reliable operation of the DES-7200. Be sure

to verify that the grounding conditions at the

installation meet the grounding requirements,

and ground all devices appropriately.

Figure 2. Grounding of the DES-7200

4D-Link 6/10 Slot Chassis-Based Switch

Power Requirements

When DES-7200 uses the AC power supply:

7200-1200AC

Rated voltage: 100-240VAC, 50/60Hz

Tolerance range: 90-264VAC, 47-63Hz

Total power: 1200W

7200-2000AC

Rated voltage: 100-240VAC, 50/60Hz

Tolerance range:

90-176VAC, 47-53Hz 1200W

176-264VAC, 57-63Hz 2000W

Total power: 2000W

When DES-7200 uses the DC power supply:

7200-1200DC

Rated voltage: -48VDC

Tolerance range:8&%Ŧ8&%Total Power: 1200W

7200-2000DC

Rated voltage: -48VDC

Tolerance range:8&%Ŧ8&%Total Power: 2000W

DES-7200 Series

Modules

Maximum Power

Consumption (W)

7200-CM1 30

7200-CM2 30

7200-CM3 50

7200-CM4 50

7200-24G 75

7200-24 85

7200-48 100

7200-24GE 75

7200-2XG 75

7200-4XG 100

7200-24P

85+15.4*N

(N indicates the PoE port being

used, of which the value is less

than 24)

7200-48P

100+15.4*N

(N indicates the PoE port being

used, of which the value is less

than 48)

7200-ASE3 100

Table 2. Power Requirements

Note:

All grounding conductors should

be connected before, and discon-

nected after the line and neutral(AC)/

input(DC) conductors.

A minimum of 10mm² (6AWG) of-

conductive grounding should be

provided to the equipment grounding

terminals on the rear panel.

For power supply unit 7200-2000DC,-

a minimum 10mm² (6AWG) of

conductive grounding should be

provided to the input terminal.

For power supply unit 7200-1200DC,-

a minimum 4mm² (10AWG) of

conductive grounding should be

provided to the input terminal.

For power supply unit 7200-2000AC-

and 7200-1200AC, a minimum

2.5mm² (12AWG) of conductive

grounding should be provided to the

input terminal. Note:

The DES-7200 provides 1+1

power supply redundancy. D-Link

recommends the use of multiple

power supplies for the equipment

to ensure continuous and stable

operation. Redundant power helps to

prevent unexpected equipment power

failures. Redundant power supplies

must be identical.

6/10 Slot Chassis-Based Switch 5

Requirements of Installation Tools

Type Tools Remarks

Common

Tools

Claw hammer,

pliers

Unpack wooden

case and transpor-

tation case.

Phillips-head

screwdriver,

straight screw-

driver, spanner

Disassemble

chassis, power

supply, fan and

modules.

Power supply

cables, network

cables, optical

ſDGTUCPFFKUVTK-

bution cables

Connect the inter-

faces.

Ruler, long

tapeline, marker

pen

Measure the instal-

lation position.

Bolts, diagonal

pliers, straps Mount the chassis.

Special-

purpose

Tools

Anti-static tool Prevent static

electricity.

Wire stripper,

crimping pliers

Create network

cables and

grounding cables.

Meter

Multimeter Test power supply

and DC resistance.

500V megohm-

meter

Test the insulation

resistance and

grounding resis-

tance.

Requirements for Rack Mounting

The DES-7200 must be used indoors. To

ensure the normal operation and prolonged

WUGHWNſNGQHVJGGSWKROGPVVJGKPUVCNNCVKQPUKVGmust meet the following requirements.

+H[QWRNCPVQOQWPVVJG&'5KPCHTCOGplease observe the following guidelines:

+PUVCNNVJGUYKVEJKPCPQRGPECDKPGVKH-RQUUKDNG+H[QWKPUVCNNVJGUYKVEJKPUKFGa closed cabinet, please ensure that the

cabinet has a good ventilation and heat

dissipation system.

Ensure that the cabinet is durable enough-

to bear the weight of the DES-7200 and its

installation accessories. (QNNQYKPIſIWTGUJQYUVJGXGPVKNCVKQPrequirements of the DES-7200. You must

TGUGTXGUWHſEKGPVURCEKPIPGCTVJGXGPVUVQensure proper ventilation. After the cables

have been connected, they should be arranged

into bundles or placed on the cabling rack, to

prevent the obstruction of air inlets and vents.

With a person on each side of the1.

DES-7200, lift the chassis while keeping

it level. Slowly move it to the front of the

frame.

Keeping the DES-7200 level, lift it to a2.

position slightly higher than the tray or the

slide rail of the cabinet. Set the chassis onto

the tray or the slide rail, and push it into the

cabinet.

Fasten the DES-7200 to the cabinet with3.

screws. Fastening notches are on both the

left and right side of the front panel on the

equipment frame. Use screws to fasten

them to the bracket of the cabinet. Once

fastened, the equipment should be stable

and immobile.

Table 3. Required Tools

Installation Site Requirements

Ventilation Requirements

Mounting the DES-7200 into the Cabinet

Ensure that the dimensions of the cabinet-

provide enough space for the installation of

the front, rear, left and right panels of the

DES-7200 for the sake of heat dissipation.

The frame should be properly grounded.-

Figure 3. Ventilation of the DES-7200

6D-Link 6/10 Slot Chassis-Based Switch

The DES-7200 provides a ventilation system,

7210-FAN for DES-7210, and 7206-FAN for

DES-7206. Carry out the following steps to install

the fan tray:

Remove the blank panel of the fan tray1.

by loosening the captive screws with a

screwdriver.

Push the fan into the cabinet along the guide2.

rail.

Tighten the captive screws with a screwdriver.3.

Figure 4 shows the installed fan tray.

Figure 4. Installing the Fan Tray of the DES-7200

The DES-7200 system offers AC and DC power

options, which can be installed in the same way

by performing the following steps:

Remove one of the two blank panels from the1.

power module by loosening the two screws

with a Phillips-head screwdriver, as shown in

Figure 5.

Figure 5. Installing the Power Supply

of the DES-7210 and DES-7206 +PUGTVVJGRQYGTUWRRN[OQFWNGKPVQVJGcabinet along the guide rail, as shown in

Figure 6.

Figure 6. Installing the Power Supply

of the DES-7210 and DES-7206

3. Tighten the screws on both sides of the

power supply by using a screwdriver, as

shown in Figure 7.

Figure 7. Installing the Power Supply

of the DES-7210 and DES-7206

Installing the Fan Tray

Installing the Power Supply

6/10 Slot Chassis-Based Switch 7

To ease handling of the system, the DES-7200

chassis is provided with a handle, which can be

installed by carrying out the following steps:

Align the handle with the sunk hole on the1.

fastening bar.

Tighten the M4 sunk crosshead screws2.

provided with the unit, as shown in Figure 8.

Figure 8. Installing the Handle of the

DES-7210 and DES-7206

The cabling rack of the DES-7210 can be install

by carrying out the following steps:

Remove the blank panel of the tracing rack by1.

loosing the captive screws with a screwdriver

and the crosshead screws with a Phillips-head

screwdriver.

+PUVCNNVJGRCPGNQHVJGVTCEKPITCEMD[2.

tightening the two captive screws with a

screwdriver and the four crosshead screws

with a Phillips-head screwdriver.

Fasten the cabling rack with the crosshead M33.

screws provided. (The cabling rack is available

in two sizes. Please select the appropriate

model.) 5KORN[UNKFGVJGCKTſNVGTQHVJG&'5KPVQthe cabinet along the guide rail.

Figure 10. Installing the Air Filter of the DES-7210

Note:

#KTſNVGTKPUVCNNCVKQPKUTGEQOOGPFGFas the last step of chassis installation.

A working ground GND and a protection

ground PGND are installed on the back of

DES-7200. GND should be directly connected

VQVJGITQWPFDCTQHVJGGSWKROGPVTQQO+HCdigital grounding bar and an analog grounding

bar exist in the equipment room, the GND

should be connected to the digital bar.

PGND should be connected to a grounding

terminal on the cabinet. The grounding terminal

should then be connected to the grounding bar

QHVJGGSWKROGPVTQQO+HCFKIKVCNITQWPFKPIbar and an analog grounding bar exist in

the equipment room, the PGND should be

connected to the analog bar.

Figure 9b. Installing the Cabling Rack

of the DES-7210

Figure 9a. Installing the Cabling Rack

of the DES-7210

Installing the Handle

Installing the Cabling Rack of the DES-7210

Installing the Air Filter of the DES-7210

Connecting the System Ground

8D-Link 6/10 Slot Chassis-Based Switch

Connect the DC power cable according to the

label on the panel of the DC power module and

the wiring shown in the following diagram.

Precautions

Before connecting the power supply, you-

must verify that the external power supply

provided matches the power module installed

of this equipment.

Before connecting the power cable, you must-

ensure that the switch of the power module is

at the OFF position.

The power cables of various colors must be-

connected to the appropriate wiring posts.

You must ensure that the power cables-

connected are in good contact.

Simple Connection Steps

Remove the protection cover of the DC wiring

terminal.

Lock the power cable to the appropriate1. VGTOKPCNCEEQTFKPIVQVJGKFGPVKſECVKQPCPFtighten the pressing screw.

Put on the protection cover and tighten the2.

screw.

Connect the other end of the power cable to3.

the corresponding socket or connector.

Connect the related AC power cable according

VQVJG+&QPVJGRCPGNQHVJG#%RQYGTOQFWNGand the location requirement, as shown in the

following diagram.

Figure 11. Connection of Grounding Posts

on the DES-7200 back

Precautions

The sectional area of the grounding-

cable should be selected according to the

maximum possible current. Use insulated

cables of good conductivity.

Do not use bare wire.-

The grounding resistance for combined- ITQWPFKPIUJQWNFDGNGUUVJCPšSimple Grounding Steps

Release the nut on the rear grounding post1.

of the equipment.

#HſZVJGVGTOKPCNQHVJGITQWPFKPIECDNGVQ2.

the grounding pole.

Tighten the nut.3.

Connect the related terminals according to4.

the above steps and the wiring diagram.

Figure 12. Schematic Diagram for the Connection

of the DC Power Cable

Figure 13. Schematic Diagram for the Connection of

the AC Power Cable

Connecting the DC Power Supply to the

Power Module

Connecting the AC Power Supply to the

Power Module

6/10 Slot Chassis-Based Switch 9

Precautions

Before connecting the power supply, you-

must verify that the external power supply

provided matches the power module installed

in this equipment.

Before connecting the power cable, you must-

ensure that the switch of the power module is

in the OFF position.

Use only a power cable with a standard 3-pin-

connector.

You must ensure that the power cables are-

securely connected.

Simple Connection Steps

+PUGTVVJGRNWIQHVJGRQYGTECDNGKPVQVJG1.

power module.

Connect the other end of the power cable to2.

the corresponding socket or connector.

Connect the cable with the RJ-45 connector

to the Ethernet port of the equipment

management module, and the other end to the

Network Management or control terminal.

Connect the end of the standard DB-9 serial

cable with the RS-232 serial port to the RS-232

serial port of the equipment management

module, and connect the other end to the NM

or control terminal.

Remove the appropriate component card1.

or blank panel blank panel according to

UGEVKQPQHVJG*CTFYCTG+PUVCNNCVKQPGuide.

Replace it with the appropriate card and2.

insert into the guide rail.

Push the card into position by using the3.

ejector, and tighten the two captive screws

on the card with a screwdriver.

Warning:

Always wear an anti-static wrist strap before1.

plugging in or unplugging a board.

&QPQVJQNFVJGIQNFſPIGTQHVJG2%$QT2.

collide the components on the PCB.

Figure 14. Components

Connecting the Cable of the Management

Module

Removing Boards from the DES-7200

7PRNWICNNECDNGUſDGTUUWEJCUQRVKECN1. ſDGTUCPF4,VYKUVGFRCKTUHTQOVJGpanel.

Loosen two captive screws on the panel.2.

Remove the board by holding the ejector3.

with both hands.

Installing Boards on the DES-7200

Note:

The DES-7200 system must have

at least one management module to

work normally.

Warning:

&QPQVJQNFVJGIQNFſPIGTQHVJG1.

PCB or collide the components

on the PCB.

When you plug/unplug a PCB2.

module, use the ejector, instead

of forcedly.

10 D-Link 6/10 Slot Chassis-Based Switch

Consult the following list to determine if the

appropriate items have been included and are

in an acceptable condition.

1. DES-7200 Chassis Carton

Verify that the individual panels have been-

installed and adjusted properly.

Wheels-

Screws-

Documentation-

Packing List-

2. Module Carton

Contains the modules, packing list and-

documentation for the DES-7200.

This system may be managed out-of-band

through the console port on the Control

Module or in-band using Telnet. Each Switch

OWUVDGCUUKIPGFKVUQYP+2#FFTGUUYJKEJis used for communication with an SNMP

PGVYQTMOCPCIGTQTQVJGT6%2+2CRRNKECVKQP(for example BOOTP, TFTP). The Switch's

FGHCWNV+2CFFTGUUKU6JGWUGTECPEJCPIGVJGFGHCWNV5YKVEJ+2CFFTGUUVQOGGVVJGURGEKſECVKQPUQH[QWTPGVYQTMKPICFFTGUUscheme.

The switch provides an RJ-45 console port

that enables a connection to a computer or

VGTOKPCNHQTOQPKVQTKPICPFEQPſIWTCVKQP6Quse the console port, you need the following

equipment:

A terminal or a computer with both a serial-

port and the ability to emulate a terminal.

A null modem or crossover RS-232 cable-

with a female DB-9 connector for the console

port on the Switch.

Verify that the external power supply matches-

the distribution panel of the cabinet.

After the equipment is installed, check that-

the front/back cabinet doors can be closed.

Verify that the cabinet has been fastened-

completely, and does not move or tilt.

Verify that the equipment has been installed-

in the cabinet, and all the cables have been

fastened to the cabinet.

8GTKH[VJCVVJGQRVKECNſDGTCPFVYKUVGFRCKT-

cables match their respective interfaces.

Verify that the cables have been bound-

appropriately.

Verify that the power cables are in good-

condition and comply with safety require-

ments.

Verify that the power module has been-

correctly fastened using the two screws on

the panel.

Turn on the power switch and verify that the-

power module is operating correctly.

3. DES-7200 Accessories Carton

Determine whether the power module of-

the equipment is the required AC or DC

module

Cabling Rack (for DES-7210 only)-

Air Filter (for DES-7210 only)-

Handle-

Fan Tray-

Power Cable (for AC power only)-

Screws-

Documentation and Packing List-

Installation Check

Checklist

Unpacking Inspection

Requirements

Connecting the Console Port (RJ-45)

Management Options

Note:

The list above contains the items

included for a standard delivery. The

actual items delivered varies based

on the purchasing contract. Please

check the items received carefully

against the packing list or purchasing

EQPVTCEV+H[QWJCXGCP[SWGUVKQPUor if there are any problems, please

contact your distributor.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere D-Link Schalten Handbücher

D-Link

D-Link DAS-3224 Bedienungsanleitung

D-Link

D-Link DAP-1650 Bedienungsanleitung

D-Link

D-Link DGS-6600 Series Bedienungsanleitung

D-Link

D-Link xStack DGS-3324SRi Bedienungsanleitung

D-Link

D-Link DFE-908x Bedienungsanleitung

D-Link

D-Link DGS-105 - Switch Bedienungsanleitung

D-Link

D-Link DU-H4 Bedienungsanleitung

D-Link

D-Link DGS-1210-26/FL Bedienungsanleitung

D-Link

D-Link DGS-1005D - Switch Bedienungsanleitung

D-Link

D-Link DES-1008E Bedienungsanleitung

D-Link

D-Link DXS-3250E - xStack Switch Bedienungsanleitung

D-Link

D-Link DGS-3024 Bedienungsanleitung

D-Link

D-Link Nuclias DNH-100 Bedienungsanleitung

D-Link

D-Link xStack DGS-3324SRi Bedienungsanleitung

D-Link

D-Link xStack DES-3228PA Bedienungsanleitung

D-Link

D-Link EasySmart DGS-1100-24 Bedienungsanleitung

D-Link

D-Link GS-1510-28P Bedienungsanleitung

D-Link

D-Link DES-3250TG Bedienungsanleitung

D-Link

D-Link des-1016a Bedienungsanleitung

D-Link

D-Link DFE-2600 Series Bedienungsanleitung

D-Link

D-Link Web Smart Switch DGS-1210-16 Bedienungsanleitung

D-Link

D-Link DES-1228P - Web Smart Switch Bedienungsanleitung

D-Link

D-Link DES-3226S Bedienungsanleitung

D-Link

D-Link DMS-107/E Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung