D-Link DGS-1010MP Bedienungsanleitung

Documentation is also available

on the D-Link website

This document will guide you through the

basic installation process for your new D-Link

10-Port Unmanaged Gigabit PoE Switch.

DGS-1010MP

Quick Installation Guide

ENGLISH

# LED Status Description

Link/Act/

Speed

(Ports 1

to 10)

Solid

amber

There is an active link negotiated at 10/100

Mbps on this port.

Blinking

amber

There is trac on the port at 10/100 Mbps.

Solid

green

There is an active link negotiated at

1000 Mbps on this port.

Blinking

green

There is trac on the port at 1000 Mbps.

PoE

(Ports

1 to 8)

Solid

green

The port is providing power to the

connected PoE-powered device.

Blinking

amber

Indicates a PoE-powered device is

connected to this PoE port, but the switch

has insucient remaining power budget

to power the device.

O There is no PoE-powered device

connected to this port.

Table 1

Front Panel Connectors

1 2 3

Figure 2

#Item Description

1Ports 1 ~ 8

10/100/1000 Mbps PoE-capable ports for

connecting Ethernet devices and PoE-

powered devices.

2Port 9

10/100/1000 Mbps Ethernet uplink port

for connecting to another switch using an

Ethernet cable.

3Port 10 100/1000 Mbps SFP uplink port for installing a

compatible SFP transceiver.

Table 2

Rear Panel Connectors

1 2 34

Figure 3

#Item Description

1Power Input This is used to connect the power cable to the

switch.

2Power Cord

Retainer Slot

This is used for securing the power cord

retainer to the switch.

3Switch GND This is used to connect the switch to ground.

4Kensington

Lock Input

This is used to attach a Kensington security

lock.

Table 3

Before You Begin

This Quick Installation Guide gives you step-by-

step instructions for setting up your DGS-1010MP

10-Port Unmanaged Gigabit PoE Switch. The model

you have purchased may appear slightly dierent

from the one shown in the illustrations. For more

detailed information about the switch, please refer

to the User Manual.

Package Contents

This DGS-1010MP package should include the

following items:

• 1 x DGS-1010MP

• 1 x Power cord

• 1 x Power cord retainer

• 1 x Rack mount kit and rubber feet

• 1 x Quick Installation Guide

If any of the above items are damaged or missing,

please contact your local D-Link reseller.

Hardware Overview

LED Indicators

1 2 3

Figure 1

# LED Status Description

1Power

Solid

green

The device is powered on.

O The device is powered o.

2PoE Max

Solid

amber

Indicates that the total PoE power output

of the switch has exceeded the Guard

Band threshold of 118 W, but is still below

the total budget of 125 W.

Blinking

amber

The total PoE budget of 125 W has been

exceeded and no additional devices can

be powered through the switch.

O The total PoE power consumption is below

the 118 W Guard Band threshold.

ENGLISH

Hardware Installation

Before You Begin

Observe the following precautions to help prevent

shutdowns, equipment failures, and personal injury:

• Install the DGS-1010MP in a cool and dry

place. Refer to the technical specications in

the user manual for the acceptable operating

temperature and humidity ranges.

• Install the switch in a site free from strong

electromagnetic sources, vibration, dust, and

direct sunlight.

• Leave at least 10 cm of space to the left and right-

hand side of the switch for ventilation.

• Visually inspect the power connector and make

sure that it is fully secured to the power cord.

• Do not stack any devices on top of the switch.

Using the Switch on a Flat Surface

The included rubber feet can be placed on the

bottom of the device to prevent it from damaging

the surface it is placed on.

1. Remove the rubber feet from the backing.

2. Stick one pad on each corner on the bottom of

the switch.

Figure 4

Mounting the Switch in a Rack

The DGS-1010MP can be mounted into a standard

19” server rack.

1. Attach the included mounting brackets to the

sides of the switch and secure them using the

provided screws.

Figure 5

2. Install the switch into the rack.

3. Use the screws that were provided with the rack

to secure the switch to the rack.

Figure 6

Grounding the Switch

This step must be completed before powering on

the switch.

Required tools and equipment for grounding

• Grounding screw (included) and one M4x6

(metric) pan-head screw (not included).

• Grounding cable (not included). The grounding

cable should be sized according to local and

national installation requirements. Depending

on the power supply and system, a 12 to 6 AWG

copper conductor is required for installation.

Commercially available 6 AWG wire is

recommended. The length of the cable depends

on the proximity of the switch to proper

grounding facilities.

• A screwdriver (not included).

Note: Verify that the system is powered o.

1. Remove the grounding screw from the back of

the device and place the #8 terminal lug ring of

the grounding cable on top of the grounding

screw opening.

2. Insert the grounding screw back into the screw

opening and use a screwdriver to tighten the

grounding screw.

ENGLISH

3. Attach the terminal lug ring at the other end

of the grounding cable to an appropriate

grounding source.

4. Verify that the connection between the

grounding connector on the switch and the

grounding source is secure.

Powering On the Switch

1. Connect the power cord to the power connector

on the switch.

2. Plug the other end of the power cord into a

nearby power socket.

Attaching the Power Cord Retainer

To prevent the power from accidently being

disconnected, it is recommend to install the included

power cord retainer.

1. With the smooth side facing up, insert the tie into

the opening below the power socket.

Figure 7

2. Plug the power cord into the power socket on

the switch.

Figure 8

3. Slide the retainer through the tie until it has

reached the end of the power cord.

Figure 9

4. Wrap the tie of the retainer strip around the

power cord and back into the retainer to lock it.

Fasten the tie until the power cord is secured.

Figure 10

Connecting to the Network

The switch can be integrated into the network

through one of the following connection methods:

Switch to End Node or Powered Device

Use a standard Ethernet cable to connect the switch

to PCs with an 10/100/1000 Mbps RJ-45 interface,

or connect and power remote IEEE 802.3af/at-

compliant devices, such as IP cameras or IP phones

using PoE.

ENGLISH

Switch to Hub or Switch

Connect the switch to another switch or hub using

the RJ-45 or SFP uplink ports.

Switch to Server

Connect the switch to a network backbone or

network server using the RJ-45 or SFP uplink ports.

ENGLISH

NOTES

Version 1.10(NA)_130x183

November 5, 2018

5402132

subsidiaries. Other trademarks are the property of their respective owners. Product specications, size and shape are subject to

change without notice, and actual product appearance may dier from that depicted on the packaging. Visit dlink.com (US) or

dlink.ca (Canada) for more details.

Technical Support

Having trouble installing your new product? D-Link’s website contains the latest

user documentation and software updates for D-Link products. U.S. and Canadian

customers can contact D-Link Technical Support through our website.

United States

Internet: http://support.dlink.com

Canada

Internet: http://support.dlink.ca

Andere Handbücher für DGS-1010MP

Inhaltsverzeichnis

Andere D-Link Schalten Handbücher

D-Link

D-Link DSS-100 Bedienungsanleitung

D-Link

D-Link DGS-1016D - Switch Bedienungsanleitung

D-Link

D-Link DCH-G020X Bedienungsanleitung

D-Link

D-Link DGS-1216T - Switch Bedienungsanleitung

D-Link

D-Link DGS-1100-08V2 Bedienungsanleitung

D-Link

D-Link DES-105 Bedienungsanleitung

D-Link

D-Link DGS-1250 Series Handbuch

D-Link

D-Link DIS-F200G Series Bedienungsanleitung

D-Link

D-Link DES-1005P Bedienungsanleitung

D-Link

D-Link DGS-1005D - Switch Bedienungsanleitung

D-Link

D-Link DES-3226SM - 1000Mbps Ethernet Switch Bedienungsanleitung

D-Link

D-Link NPP-C61BLK242 Bedienungsanleitung

D-Link

D-Link TM DES-6500 Bedienungsanleitung

D-Link

D-Link DES-3225G Series Bedienungsanleitung

D-Link

D-Link DSS-16+ Bedienungsanleitung

D-Link

D-Link DSD-150 - SecureSpot Internet Security... Bedienungsanleitung

D-Link

D-Link DES-7200 Bedienungsanleitung

D-Link

D-Link DES-1228 - Web Smart Switch Bedienungsanleitung

D-Link

D-Link DSS-5 - 10/100 Switch, Desktop Bedienungsanleitung

D-Link

D-Link DES-3624i Bedienungsanleitung

D-Link

D-Link DXS-3250 - xStack Switch - Stackable Bedienungsanleitung

D-Link

D-Link DKVM-2KU Bedienungsanleitung

D-Link

D-Link DMS-105 Bedienungsanleitung

D-Link

D-Link DGS-1008T Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung