D-Link DGS-1210 Series Bedienungsanleitung

- 1 -

Manual how to bind the

DGS-1210 Switches into the Nuclias Connect

For Nuclias Connect Hardware DNH-100 Rev.A and Nuclias Connect Software DNC-100

For DGS-1210 Rev.F and Rev.G

To bind the DGS-1210 with Hardware Revision (Rev.) F and G into

the Nuclias Connect please follow these steps.

1. Requirements

- DGS-1210 Switch in Rev.F with firmware version 6.30.xx or higher

- DGS-1210 Switch in Rev.G with firmware version 7.30.xx or higher

This you can download from our D-A-CH-BE-NE-LUX web sites https://www.dlink.com

or from https://ftp.dlink.de/dgs/dgs-1210/driver_software/

- DNH-100 Nuclias Conenct Hub with the actual Firmware 1.2.0.1 or higher.

Or DNC-100 Nuclias Connect Software in the actual Version 1.2.0.9 or higher.

2. Preparations

Different to the DAP Access Points the DGS-1210 must be pre-configured so far that it

got an IP-address from the DHCP-Server in the network or has a static IP-address

compatible to the network.

By default the DGS-1210 has the static IP-address 10.90.90.90

with subnet mask 255.0.0.0

Change the TCP/IP of the network connection temporarily to configure the DGS-1210.

Alternative or if you don’t know the IP-address of your DGS-1210 you can use our

Software D-Link Network Assistant (DNA) to find it out or to change it.

See following screenshot.

You can download the DNA from

https://ftp.dlink.de/software/DNA/D-Link_Network_Assistant_DNA_40021_all_en.zip

With the PC mouse go over the DGS-1210 entry and then click onto IP on the right.

Then you can change the IP-address of the DGS-1210.

- 2 -

Note:

In the following steps granting that you already made a setup in

your DNH-100 / DNC-100 (following named as NC) and have it in use

with DAP-models, so the NC has a basic setup already.

3. Call the setup of your NC and log-in.

We recommend to use the English setup because the translation in other languages isn’t fine sometimes.

- Chose English.

- Enter the username admin and your configured Admin-password.

- If necessary enter the displayed CAPTCHA.

- Click onto Login.

4. On the left go to the menu Configuration and then Create Profile.

Upper-right click onto Add Network to create a new Switch-Profile.

Note:

Switches can’t be bound into AP-Profiles, also AP not into Switch-Profiles.

5. Create a newSite.

Give the site and the network a name and then click onto Next.

- 3 -

- Chose the Country where the switch has to work.

- If necessary modify the Time Zone.

- Set a hook at Switch.

- At Series Supported a hook must be at DGS-1210.

- At Password you must enter the Admin-password this the DGS-1210 has to get from

the NC-Profile as soon as it will be bound-in.

Click onto Next.

7. Normally it is fine to use Layer 2.

Click onto Next.

8. Upper-left click onto Discovery to let search for DGS-1210 switches.

- 4 -

9. The in the network available and compatible DGS-1210 will be found.

Mark the DGS-1210 this you want to bid into the NC-Profile.

Enter the Admin-password this the DGS-1210 actually has.

- The default Admin-password is admin.

- If you already have changed the Admin-password then enter this.

Click onto Import to take over the marked DGS-1210 into the NC-Profile.

Recommendation!!

For each DGS-1210 create an own NC-Profile.

Else it can become difficult because the NC displays all LAN ports of all DGS-1210 in the

NC-profile like they are one DGS-1210.

Example: The LAN ports of three DGS-1210-10P will be listed as 30 ports –a

differentiation which port if from which switch won’t be so easy.

10. Click onto Yes.

- 5 -

11. The displayed NC flickers a few times now.

Please what until this ends.

Click onto Apply & Exit.

12. After 3-5 minutes the switch will be displayed in the Dashboard.

Click onto this…

…then the Status of the DGS-1210 will be displayed.

Normally at this moment it is boarding.

Status is orange = Boarding

After additionally 3-5 minutes the Status is green = Connected

The DGS-1210 can be managed and configured via the NC now.

- 6 -

13. To access the possible settings of the DGS-1210 in the NC, on the left go to the

menu Configuration and then Profile Settings.

There inside the created profile of the DGS-1210 you can make several settings.

Note:

Unfortunately it is not possible to make all settings of a DGS-1210 via the NC (yet).

The DGS-1210 still has the fully setup like a standalone switch.

The access is via a web browser via his IP-address.

The Admin-password is this you configured via the NC profile (see step 9 on page 4).

With it the binding of the DGS-1210 Rev.F and/or G into the Nuclias Connect is finished.

Example:

Each a DGS-1210 Rev.F and G is bound into the Nuclias Connect:

Andere Handbücher für DGS-1210 Series

Inhaltsverzeichnis

Andere D-Link Schalten Handbücher

D-Link

D-Link DES-1005D Bedienungsanleitung

D-Link

D-Link DGS-1008P Bedienungsanleitung

D-Link

D-Link DGS-1510 Series Bedienungsanleitung

D-Link

D-Link DKVM-4 - KVM Keyboard Video Mouse Switch... Bedienungsanleitung

D-Link

D-Link DES-1008P Bedienungsanleitung

D-Link

D-Link DWS-3160-24TC Bedienungsanleitung

D-Link

D-Link DGS-1210-28MP/FL Bedienungsanleitung

D-Link

D-Link DGS-3000-52X Bedienungsanleitung

D-Link

D-Link DGS-1250-28X Bedienungsanleitung

D-Link

D-Link DGS-1016A Bedienungsanleitung

D-Link

D-Link DE-816TP - Hub 16Port 10MBs 16RJ45 1BNC 1A Ui... Bedienungsanleitung

D-Link

D-Link xStack DGS-3612G series Bedienungsanleitung

D-Link

D-Link DUB-H4 - Hub - USB Bedienungsanleitung

D-Link

D-Link DFE-2624 - Hub - Stackable Bedienungsanleitung

D-Link

D-Link TM DES-6500 Bedienungsanleitung

D-Link

D-Link Dis-200G Series Bedienungsanleitung

D-Link

D-Link DXS-3227 - xStack Switch - Stackable Bedienungsanleitung

D-Link

D-Link DIS-100G-5W Bedienungsanleitung

D-Link

D-Link DGS-1210/ME series Handbuch

D-Link

D-Link DGS-1026MP Bedienungsanleitung

D-Link

D-Link DGS-1016A Bedienungsanleitung

D-Link

D-Link DI-707 Bedienungsanleitung

D-Link

D-Link DGS-1008T Bedienungsanleitung

D-Link

D-Link DGS-1016T Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung