D-Link DGS-6600-48TS Bedienungsanleitung

This document will guide you through the basic

installation process for your new D-Link

chassis-based Switch.

Building Networks for People

DGS-6600 Series

Documentation also available on CD

and D-Link Website

Quick Installation Guide

4 Slot Chassis-Based Switch

2 u D-Link DGS-6604 Modular Switch

ENGLISH

About This Guide

This guide contains step by step instructions

for setting up the D-Link DGS-6604 chassis-

based switch. Please note that the model you

have purchased may appear slightly different

from those shown in the illustrations.

Please read this manual carefully before using

the product, paying special attention to safety

warnings so as to avoid injury or damage to

equipment.

This manual is intended for users who have

experience in installing and maintaining

network hardware, and assumes that users

are familiar with standard networking terms

and concepts.

Product Overview

D-Link’s DGS-6604 chassis-based switch is

an intelligent and high-performance multi-layer

LAN device designed for enterprise campus

and metropolitan area networks (MAN). It is

ideal for deployment in environments where

uninterrupted network applications and a high

level of performance, security and control are

required.

Featuring exible modular architecture and

industry standard compliance, the switch

provides scalable expansion and a high

level of investment protection for businesses

and telecom carriers to deploy Gigabit and

10-Gigabit packet switching and routing for

ofce networking and Ethernet-based Internet

services to homes.

Warning s

Power Supply Safety Warning

Ground the device before power-

ing on to guard against power

surges.

Be sure that all cables are ground-

ed correctly.

Static Electricity Protection

Warning

Always wear an anti-static wrist

strap when contacting the chassis

to prevent static damage.

Laser Safety Warning

CLASS 1 LASER PRODUCT

Directly looking at the optical in-

terface or optical bers may cause

eye damage.

Fan Safety Warning

The fan mechanism is dangerous.

Avoid touching the area near the

fan.

Transportation Safety Warming

The device and components may

comprise more than 27 kg in total.

Use care when inserting or remov-

ing heaving components.

Maintenance Warning

Maintenance should only be car-

ried out by qualied service techni-

cians

D-Link DGS-6604 Modular Switch u 3

ENGLISH

Preparation for Installation

To ensure normal operation and prolonged life

of the DGS-6604, the appropriate temperature

and humidity must be maintained in the equip-

ment room.

If the equipment room’s temperature and

humidity do not meet the requirements. the

equipment may sustain damage.

Operating Temperature Operating Humidity

0ºC-50ºC 10%-90% RH

non-condensed

Table 1. Temperature and Humidity

Requirements

Notes:

1. The ambient temperature and

humidity should be measured

at the point that is 1.5m above

the oor and 0.4m in front of the

equipment when there is no pro-

tective plate in front or back of the

equipment rack

2. The short-term working condi-

tions apply where the continuous

working period does not exceed 48

hours and the cumulative total pe-

riod within a year does not exceed

15 days

Static Discharge Damage Prevention

To prevent damage from static electricity,

please conform to the following guidelines:

1. Be sure to install an adequate ground for

all electronic equipment.

2. Use appropriate dust prevention measures.

3. Maintain the required humidity in the oper-

ating environment

4. Always wear an anti-static wrist strap when

working around any electronic circuitry.

5. Hold a circuit board by its edges. Do not

touch any components on the PCB.

6. Do not allow clothing to touch a circuit

board. An antistatic wrist strap can only

prevent static electricity from the human

body, but cannot mitigate static electricity

from clothing.

Moving the Device

The DGS-6604 is quite heavy. When handling,

please pay close attention to the following

guidelines:

• Avoid moving the equipment frequently.

• If you nd the chassis weight unbearable,

do not attempt to lift the equipment alone.

• Lift and move the chassis using the han-

dles on the top panel .

• Turn off all power supplies and unplug all

power cables before moving the equip ment.

• Completely loosen the thumb/Phillips

screws and pull the card levers to remove

each and all line cards, fan tray, and power

mod ules from the chassis before moving it.

Figure 1. Correctly Moving the DGS-6604

Do not move the equipment by

grasping the panels, power sup-

ply handles, or ventilation holes,

as they are not designed to bear

weight.

4 u D-Link DGS-6604 Modular Switch

ENGLISH

System Grounding Requirements:

Proper grounding will help to ensure stable

and reliable operation of the DGS-6604. Be

sure to verify that the grounding conditions

at the installation meet the grounding

requirements and ground all devices

appropriately.

Ground Connection

Power Requirements

The power consumption and heat dissipation

gures of the various DGS-6604 components are

listed in the table below:

DGS-6600 Series

Module

Maximum

Power

Consumption

(W)

Heat

Dissipation

(BTU/Hour)

DGS-6600-CM 54 184

DGS-6600-48T 110 375

DGS-6600-48S 119 405

DGS-6600-48TS 114 390

DGS-6600-48P 873 2979

DGS-6600-8XG 200 684

DGS-6600-24SC2XS 106 360

DGS-6600-FAN

Fan Tray

43 144

DGS-6600-PWR

AC Power Supply

854

(@110VAC

or 220 VAC)

2913

(@110VAC

or 220 VAC)

Figure 2. Grounding of the DGS-6604

Note:

All grounding conductors should

be connected before the AC power

is applied to the DGS-6604 in-

stalled AC power supplies.

The DGS-6604 with AC power

supplies must be grounded with

a minimum of 0.823 mm2 (or

18AWG) of conductive ground-

ing cable. This cable is connected

between the Equipment Room

Ground and the DGS-6604 Chas-

sis Ground Terminal.

Table 2. Card Power Requirements

Note:

The DGS-6604 provides either

1+1, 2+1, or 3+1 redundant AC

power supplies. D-Link

recommends to use multiple

power supplies for the equipment

to ensure continuous and stable

operation. Redundant power

supplies help to prevent

unexpected power failures.

Redundant power supplies must

be identical.

D-Link DGS-6604 Modular Switch u 5

ENGLISH

Installation Tools Requirements

Type Tools Remarks

Common

Tools

Claw hammer,

pliers

Unpack wooden

case and

transportation case.

Phillips-head

screwdriver,

straight

screwdriver,

spanner

Disassemble

chassis, power

supply, fan and

modules

Power supply

cables,

network

cables, optical

bers and

distribution

cables

Connect the

interfaces.

Ruler, long

tapeline,

marker pen

Measure the

installation position.

Bolts, diagonal

pliers, straps

Mount the chassis.

Special

purpose

tools

Anti-static tool Prevent static

electricity.

Wire stripper,

crimping pliers

Create network

cables and

grounding cables.

Meter Multimeter Test power supply

and DC resistance.

500V

Megohm-

meter

Test the insulation

and grounding

resistance

Table 3. Required Tools

Installation Site

Requirements

The DGS-6604 must be used indoors. To

ensure the normal operation and prolonged

useful life of the equipment, the installation

site must meet the following requirements.

Requirements for Rack Mounting

If you plan to mount the DGS-6604 in a frame,

please observe the following guidelines:

• Install the switch in an open cabinet if

pos sible. If you install the switch inside

a closed cabinet please ensure that the

cabi net has a good ventilation and heat

dissipation system.

• Ensure that the cabinet is durable enough

to bear the weight of the DGS-6604 and its

installation accessories.

• Ensure that the dimensions of the cabinet

provide enough space for the installation

of the front, rear, left and right panels of

the DGS-6604 for the purpose of heat

dissipation.

• The frame should be properly grounded.

Ventilation Requirements

Following gure shows the ventilation

requirements of the DGS-6604. You must

reserve sufcient space near the vents to

ensure proper ventilation. After the cables

have been connected, they should be

arranged into bundles or placed on the cabling

rack to prevent the obstruction of air intakes

and vents.

Figure 3. Ventilation of the DGS-6604

Mounting the DGS-6604 into the Cabinet

1. Lift the chassis (seek assistance if the

chassis is more then you can lift safely)

while keeping it level Slowly move it to the

front of the frame.

2. Keeping the DGS-6604 level, lift it to a

posi tion slightly higher than the tray of the

slide rail of the cabinet. Set the chassis

onto the tray or the slide rail, and push it

into the cabinet.

3. Fasten the DGS-6604 to the cabinet with

screws. Fastening notches are on both the

left and right sides of the front panel on the

6 u D-Link DGS-6604 Modular Switch

ENGLISH

equipment frame. Use screws to fasten

them to the bracket of the cabinet/ Once

fastened, the equipment should be stable

and immobile.

Installing the Fan Tray

The DGS-6600-FAN fan tray is used as the

DGS-6604’s ventilation system. Carry out the

following to install the fan tray:

1. Use the thumb-screws to remove the fan

tray blank panel.

2. Insert the fan tray into the guide rail of the

fan tray slot.

3. Secure the fan tray by tightening the fan

tray’s captive-screws.

Figure 4. Installing the Fan Tray

Installing the Power Supply(s)

The DGS-6604 switch is powered up using an

AC power supply. The procedure for installing

the AC power supply is shown in the diagram

below:

Figure 5. Installing the Power Supply

Connecting the System Ground

A working ground GND is installed on the back

of DGS-6604. GND should be directly

connected to the ground bar of the equipment

room. If a digital grounding bar and an analog

grounding bar exist in the equipment room, the

GND should be connected to the digital bar.

Ground Connection

Figure 6. Ground Connections on the back of the

DGS-6604

Precautions.

The sectional area of the grounding cable

(min. of 18AWG) should be selected to safely

conduct the maximum possible current. Use

insulated cables of good conductivity.

• Do not use bare wire.

• The grounding resistance for combined

grounding should be less than 1 Ohm (Ω).

Simple Grounding Steps

• Unfasten the nut on the rear grounding

post of the equipment.

• Afx the terminal of the grounding cable to

the grounding pole.

• Fasten the nut back on the grounding post.

• Connect the other end of the grounding

cable to a suitable grounding bar.

D-Link DGS-6604 Modular Switch u 7

ENGLISH

Installing the Air Filter of the DGS-6604

On the back of the chassis on the edge of the

right-side is a vertical slot where the air lter

can be tted. Slide in a cleaned or new air lter

into the slot as per the following diagram. Then

screw the two thumb/Phillips screws (see the

diagram arrows) to secure the air lter into the

chassis. With the air lter installed screw-in two

screws on the side of the chassis as indicted

by the red arrows in the diagram.

Figure 7. Installing the Air Filter

Air lter installation is recommend-

ed as the last step of the chassis

installation.

Connecting the AC Power Supply to the

Power Module

Use the related AC power cable to connect to

the AC power module panel, as indicated in

the following diagram:

Figure 8. Connecting AC to the Power Module

AC Power Supply Connection Precaution

• Verify that the provided external power

sup ply matches the power module installed

in the Switch before connecting the power

supply.

• Use a power cable with a standard 3-pin

connector to make the power connection.

• Ensure that the connected power cables

have good contacts.

• Once the power cable is plugged-in at both

power outlet and the power supply, the

power supply will immediately start.

Simple AC Power Connection Steps

1. Insert the power cable’s plug into the

power module.

2. Secure the power cable to the cable clip on

the right.

3. Connect the other end of the power cable

into the corresponding socket or connector.

8 u D-Link DGS-6604 Modular Switch

ENGLISH

Connecting the Serial Cable of the Man-

agement Module

Simple CPU Module Cable Connection

1. Connect the RJ45 connector of an Ethernet

cable to the Ethernet port of the Switch’s

management module (DGS-6600-CM) and

connect the other end of the cable to any

TCP/IP capable device that is able to exe-

cute Telnet or SSH.

- or -

2. Connect the standard DB9 end of the

serial cable to the RS-232 serial port of

the Switch’s management module and the

other end to the PC/Notebook or control

terminal.

- or -

3. Connect a USB cable with a USB Standard

B Connector to the Standard B receptacle

on the Switch’s management module. Con-

nect the other end to a computer equipped

with a USB port capable of supporting a

serial interface using the PL-2303 USB

Serial Driver SW from Prolic Technology

Inc..

Removing Boards from the DGS-6604

Carry out the following steps to remove boards

from the DGS-6604:

1. Unplug all copper/ber cabling, i.e. RJ45

twisted-pair and ber optic cables, from the

board to be removed.

2. Loosen and unscrew the panel’s two cap-

tive screws.

3. Use both hands to pull the levers, on the

left and right hand sides of the board, to

remove the board from the DGS-6604, as

shown in the following diagram.

Caution

Before removing/adding a board,

always wear an anti-static wrist

strap.

Take care not to hold the edge of

the PCB or collide the components

of the PCB..

Figure 9. Removing a board from the chassis

Installing Boards on the DGS-6604

Carry out the following steps to install boards

in the DGS-6604:

1. Remove the component card or blank panel

as instructed in the section.

2. Insert the new board into the guide rail of

the vacant slot.

3. Use the levers on the left and right hand

side to push the board into position and

tighten the two captive screws on the board

using a straight screw driver.

Caution

1. Take care not to hold the

edge of the PCB or collide the

compo nents of the PCB.

2. Always use the levers to plug/

unplug a PCB module. Never

use force to remove a PCB

module.

D-Link DGS-6604 Modular Switch u 9

ENGLISH

Figure 10. Installation Check

Installation Check

Verify that the external AC power supply

provides the correct voltage and frequency.

Verify that the cabinet has been fastened

completely, and does not move or tilt.

Verify that the Power Supplies, CM and Line

Cards have been installed in the chassis.

Verify that the optical ber and twisted pair

cables match their respective interfaces.

Verify that the cables have been bound

appropriately and are not subject to any

excess stress.

Verify that the power cables are in good

condition and comply with safety requirements.

Verify that the power module has been rmly

installed into the backplane connector.

Turn on the power switch and verify that the

power module is operating correctly.

Unpacking Inspection

Requirements

Checklist

1. DGS-6604 Chassis Carton

• DGS-6604 Chassis (no cards installed)

1. Card Module Carton (s)

• 1 CM Card DGS-6600-CM

• Line Cards (specic per order)

• Power Supplies Units (number specic per

order)

2. DGS-6604 Accessories Carton including:

• AC Power Cord

• RS-232 Console Cable (9 pin D-Sub)

• USB Console Cable (Type A to Type B)

• Fan Tray

• Air Filter

• CD software and manual

• QIG

Management Options

The system may be managed out-of-band

through the console port(s) and Ethernet port

on the Control Module or in-band using Telnet/

SSH. Each Switch must be assigned its own IP

address, which is used for communication with

an SNMP network manager or other TCP/IP

application (for example BOOTP, TFTP). The

Switch’s default IP address is 10.90.90.90 (out-

of-band IP address). The user can change the

default IP address to meet the specications of

your networking address scheme.

Connecting the Console Port (USB or 9

Pin D-Sub)

The switch provides a USB or 9 Pin D-Sub

Serial Connection to a computer or terminal

for monitoring and conguration. To use

the console port, you need the following

equipment:

• A terminal or a computer with a 9 pin serial

port /USB port and the ability to emulate a

terminal.

• A null modem or cross-over RS-232 cable

with a female DB-9 connector for the

switch’s console port.

- or -

10 u D-Link DGS-6604 Modular Switch

ENGLISH

• A USB cable (with a Type B USB connector

for the switch’s USB console port) and the

Serial USB driver installed on the computer

used to connect to the console.

Download the USB-Serial Driver here:

http://www.prolic.com.tw/eng/

downloads.asp?ID=31

Conrm the driver for your Operating

System is for the X chip series.

To connect a terminal to the console port

1. Connect the supplied RJ-45-to DB-9 adapt-

er cable to the standard 9-pin serial port on

the PC. Connect the other end of the cable

to the console port on the switch. Set the

terminal emulation software as fol lows:

• Baud rate: 115200

• Data bits: 8

• Parity: None

• Stop bits: 1

• Flow control: None

2. Select VT100 for the terminal emulation

mode.

3. After you have correctly set up the terminal,

plug the power cable into the power sup-

plies on the switch. The boot sequence will

appear in the terminal.

4. Press the Enter key at the password

prompts. There is no default password for

the Switch.

5. Enter the commands to complete your de-

sired tasks. Many commands require ad-

ministrator-level access privileges. See the

CLI Reference Guide on the documen tation

CD for a list of all commands and additional

information using the CLI.

Telnet Management Users may also access

the switch CLI by using PC’s Command Prompt.

To access it from your computer, users must rst

ensure that a valid connection is made through

the Ethernet port of the Switch and your PC,

and then click Start > Programs > Accessories >

Command Prompt on your computer. Once the

console window opens, enter the command

telnet 10.90.90.90 (depending on congured

IP address) and press Enter on your keyboard.

You should be directed to the opening console

screen for the CLI of the switch, press the En-

ter key at the password prompts. There is no

default password for the Switch.

SNMP-Based Management

You can manage the Switch with D-Link

D-View or any SNMP-compatible console

program. The SNMP function is disabled by

default for D-Link managed switches.

Additional Information

If you are encountering problems setting up

your network, please refer to the User’s Guide

that comes with the switch. It contains many

more rules, charts, explanations and examples

to help you get your network up and running.

Additional help is available through our of-

ces listed online. To learn more about D-Link

products or marketing information, please visit

the website http://www.dlink.com, which will

re-direct you to your appropriate local D-Link

website.

Technical Support

United Kingdom (Mon-Fri)

website: http://www.dlink.co.uk

FTP: ftp://ftp.dlink.co.uk

Home Wireless/Broadband 0871 873 3000

(9.00am–06.00pm, Sat 10.00am-02.00pm)

Managed, Smart, & Wireless Switches, or

Firewalls 0871 873 0909 (09.00am- 05.30pm)

(BT 10ppm, other carriers may vary.)

Ireland (Mon-Fri)

All Products 1890 886 899 (09.00am-06.00pm,

Sat 10.00am-02.00pm)

Phone rates: €0.05ppm peak, €0.045ppm off

peak times

Andere Handbücher für DGS-6600-48TS

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere D-Link Schalten Handbücher

D-Link

D-Link DSS-24+ Bedienungsanleitung

D-Link

D-Link DUB-H7 - Hub - USB Bedienungsanleitung

D-Link

D-Link 48-Port 10/100Mbps Web-Smart Switch with 4-Port 10/100/1000Base-T and 2-Port Combo SFP... Bedienungsanleitung

D-Link

D-Link DES-3526 - Switch - Stackable Bedienungsanleitung

D-Link

D-Link KVM-221 2 Bedienungsanleitung

D-Link

D-Link DE-816TP - Hub 16Port 10MBs 16RJ45 1BNC 1A Ui... Bedienungsanleitung

D-Link

D-Link DSS-16+ Bedienungsanleitung

D-Link

D-Link DIS-F100G Series Bedienungsanleitung

D-Link

D-Link DGS-1100-05V2 Bedienungsanleitung

D-Link

D-Link SmartPro DGS-1500-20 Bedienungsanleitung

D-Link

D-Link DGS-F1010P-E Bedienungsanleitung

D-Link

D-Link DWS-3160-24TC Bedienungsanleitung

D-Link

D-Link xStack DGS-3420-28PC Handbuch

D-Link

D-Link DFE-2600 Series Bedienungsanleitung

D-Link

D-Link DES-3528 - xStack Switch - Stackable Bedienungsanleitung

D-Link

D-Link GO-SW-16G Bedienungsanleitung

D-Link

D-Link KVM-440 Bedienungsanleitung

D-Link

D-Link DGS-1005G Bedienungsanleitung

D-Link

D-Link DGS-3100 SERIES Bedienungsanleitung

D-Link

D-Link DFE-904 Bedienungsanleitung

D-Link

D-Link DGS-1100-10MPP Bedienungsanleitung

D-Link

D-Link DGS-1210-10P Bedienungsanleitung

D-Link

D-Link DES-1008D Bedienungsanleitung

D-Link

D-Link DXS-1210-10TS Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung