Da-Lite DELUXE MODEL B Bedienungsanleitung
48709 Rev. 6/04
DA-LITE IS MORE
THAN PROJECTION SCREENS
Da-Lite Tripod, Wall and
Ceiling and Electric Screens
Da-Lite Lecterns
Da-Lite
Project-O-Stands
and Easels
Da-Lite
Monitor Mounts
POWER
PRESENTATION PRODUCTS
The
In
Operating Instructions
for
DELUXE MODEL B®
DA-LITE SCREEN COMPANY, INC.
3100 North Detroit Street
Post Office Box 137
Warsaw, Indiana 46581-0137
Phone: 574/267-8101
800-622-3737
Fax: 574/267-7804
http:// www.da-lite.com
e-mail: [email protected]
INSTALLATION
The Deluxe Model B must be suspended from
the ceiling or used with extension type wall
brackets to allow room for the Automatic
Tensionizer.
FOR WALL MOUNTING
Special extension wall
brackets such as Da-Lite’s
No. 6, No. 11 or No.23
brackets must be used if
screen is to be wall
mounted. Check with your
dealer to determine which
best fits your needs.
Brackets should be fastened
securely to a solid surface
such as a wooden
reinforcement board and not
in the plaster only. Rarely
will wall studs be found to
support both ends of a
screen. Various types of
fasteners are available from
local hardware stores.
FOR CEILING SUSPENSION
If the screen is to be ceiling
mounted, two screw hooks
placed in a beam or other
solid surface will do the job.
For dropped ceilings, Da-
Lite’s T-Bar Scissors Clip
may be purchased.
NOTE: Whichever method is used, the screen
should be free to swing forward and back and
not be anchored rigidly. Mount the screen so
that bottom of picture surface, when fully
extended, will be above heads of viewers.
YOU HAVE MADE A WISE
SELECTION…
Care in mounting and care in correct
operation will mean a long and satisfac-
tory life for your Da-Lite wall/ceiling
screen. Locate the screen where the
audience can best see it.
SETTING UP YOUR SCREEN
These illustrations (all rear views for
simplification) show how easy the Deluxe
Model B Screen is to operate.
1. To start unrolling the
picture surface, pull down
on cord pull knob. Then
with hand resting on the
handle, pull screen down.
2. The Automatic
TENSIONIZER moves into
position in a precision-
like manner.
3. When surface is down,
a simple press of
contour-shaped handle
locks it into position…
ready for the show!
4. To re-roll picture
surface–press firmly
downward and counter-
clockwise on flat handle
to release lock. Permit
surface to re-roll rapidly
into case. Control upward
movement by lightly
holding handle or cord
pull knob.
PROTECT YOUR SCREEN by keeping it rolled in
its case when not in use. Always examine both
front and back of surface before re-rolling into
case to make certain screen is free of dust, dirt
or other foreign matter. Use a very soft duster,
brush gently to remove foreign particles.
SILVER LENTICULAR PICTURE SURFACES
Silver Lenticular surfaces are
sensitive to temperature changes
which may temporarily cause
slight unevenness after a screen
has been rolled up for a time. If
uneven when first opened for use,
put on normal tension with the ten-
sioning device and allow it to
stand at room temperature of 70 to 75 degrees for five
or ten minutes. The surface will equalize itself and be
normally flat for projection in a very short time.
SCREEN ACCESSORIES
WALL BRACKETS
Da-Lite No. 6 and No. 11 Non-adjustable wall
brackets and No. 23 adjustable extension wall
brackets are ideal for keystone elimination,
chalkboard clearance, or corner mounting. The
screen brackets should be fastened to the
studding or other solid surface and
not in the plaster only.
Suspend screen from
“D” rings.
No. 23 ADJUSTABLE
WALL BRACKETS
Screen can be extended
181⁄4", 20" or 24" from
wall by wing nut and
bolt adjustment.
No. 11 WALL BRACKETS
Screen can be extended
10" or 14" from wall by
changing position of
bracket.
No. 6 WALL BRACKETS
Screen can be extended
6" from wall.
T-BAR SCISSORS CLIP
For Dropped Ceilings
50 lb. max. load
capacity.
TILT LOCK
For Keystone Elimination
Holds back bottom of
screen in tilted position
to eliminate keystoning.
SCISSORS
CLIP
ADAPTER
S-HOOK
D-RING
T-BAR
DELUXE MODEL B
EXCLUSIVE FEATURES
•Built-On Hanging Brackets for Ceiling
•Rugged Construction
•Octagon No-Rub Flat Back Case
•Seamless in All Sizes
•Uniform Automatic Tensioning
•Wrinkle-Free Pictures
•Completely Self-Storing
•Camlok Roller System Prevents Picture
Surface From Pulling Off Metal Roller
ADJUSTMENT NOTE
NOTE: Tensioning of the Deluxe Model B
picture surface was made at the factory.
Should more tension be required, the screw in
the channel holding the upper tension arm
assembly should be moved upward in holes
allotted for this purpose. For any adjustment, it
is recommended that the screen be removed,
placed on a flat surface and a pair of pliers and
a Phillips screwdriver be used in removing the
screw and nut.
PROTECT YOUR SCREEN
Before re-rolling surface into case, examine
both front and back of surface to be sure they
are free of foreign matter.
Upper tension
arm assembly
Nut Screw
Channel
BACK VIEW OF SCREEN
Case
Upper
tension
arm
assembly
Andere Da-Lite Projektionsfläche Handbücher
Da-Lite
Da-Lite IDEA Panoramic Bedienungsanleitung
Da-Lite
Da-Lite Presenter P-50 Bedienungsanleitung
Da-Lite
Da-Lite ViewShare Advantage Electrol Retrofit Bedienungsanleitung
Da-Lite
Da-Lite IDEA Screen Bedienungsanleitung
Da-Lite
Da-Lite B Bedienungsanleitung
Da-Lite
Da-Lite TENSIONED DIRECTOR ELECTROL Bedienungsanleitung
Da-Lite
Da-Lite Picture King Bedienungsanleitung
Da-Lite
Da-Lite ADVANTAGE ELECTROL Bedienungsanleitung
Da-Lite
Da-Lite Fast-Fold NXT Bedienungsanleitung
Da-Lite
Da-Lite BG Bedienungsanleitung
Da-Lite
Da-Lite Whiteboard Mount Bedienungsanleitung
Da-Lite
Da-Lite PROFESSIONAL ELECTROL Bedienungsanleitung
Da-Lite
Da-Lite Cosmopolitan Electrol Bedienungsanleitung
Da-Lite
Da-Lite ExecutiveElectrol Bedienungsanleitung
Da-Lite
Da-Lite LARGE ADVANTAGE DELUXE ELECTROL Bedienungsanleitung
Da-Lite
Da-Lite ADVANTAGE DELUXE ELECTROL Bedienungsanleitung
Da-Lite
Da-Lite UTB Contour Bedienungsanleitung
Da-Lite
Da-Lite Versatol Bedienungsanleitung
Da-Lite
Da-Lite MULTI-MASK IMAGER Bedienungsanleitung
Da-Lite
Da-Lite TENSIONED EXECUTIVE ELECTROL Bedienungsanleitung
