Da-Lite DESIGNER CONTOUR ELECTROL Series Bedienungsanleitung

DA-LITE SCREEN COMPANY, INC.

3100 North Detroit Street

Post Office Box 137

Warsaw, Indiana 46581-0137

Phone: 574-267-8101

800-622-3737

Fax: 574-267-7804

Toll Free Fax: 877-325-4832

www.da-lite.com

e-mail: [email protected]

Instruction Book for

DESIGNER CONTOUR®ELECTROL®

WITH BUILTIN INFRARED REMOTE

The Da-Lite Difference.

IMPORTANT SAFETY INSTRUCTIONS

When using your video equipment, basic safety precautions

should always be followed, including the following:

1. Read and understand all instructions before using.

2. Position the cord so that it will not be tripped over, pulled,

or contact hot surfaces.

3. If an extension cord is necessary, a cord with a current

rating at least equal to that of the appliance should be used.

Cords rated for less amperage than the appliance may

overheat.

4. To reduce the risk of electric shock, do not disassemble this

appliance. Contact an authorized service dealer when repair

work is required. Incorrect reassembly can cause electric

shock when the appliance is used subsequently.

5. The use of an accessory attachment not recommended by

the manufacturer may cause a risk of fire, electric shock, or

injury to persons.

SAVE THESE INSTRUCTIONS

Carefully unpack screen and remove outer wrapping from

case.

Remove the black tape from the slat bar after the case has

been installed.

There are three ways to install the Designer Contour®Electrol®

with built-in Infrared Remote: Wall Mount, Ceiling Mount, or

Ceiling Hook. Procedures for each method are as follows:

Wall Mount

1. Secure the wall mount bracket to the wall at the desired

height. Bracket should be fastened to wall studs or

some reinforcement within the wall. Concrete or brick

walls require special fasteners and anchors.

2. Make sure the bracket is level. See figure 1 for

reference dimensions.

3. Keep in mind you will need at least 5/8" between the

ceiling and the top of the wall mount bracket to be able

to position the case on the bracket.

4. Mount the screen case on the wall bracket as shown in

figure 1. Be sure the case is fully seated on the bracket.

Tighten the stop screws against the wall bracket.

Ceiling Mount

1. Do not remove the wall mount bracket, even if you are

not using it for mounting. This provides structural

stability to the case.

2. Be sure the ceiling has adequate reinforcement to

attach the screen brackets.

3. The top of the screen case has a channel that the ceiling

mount brackets slide into. Remove the end cap on the

right end of the case and insert the brackets into the

case channel. Lock the brackets in place by tightening

two set screws. Refer to figure 2. Mount can not be

more than 12" from end of case.

4. Hold the screen case up to the ceiling and mark the hole

locations. Drill holes into the ceiling and attach screen

with the appropriate fasteners for your ceiling.

Ceiling Hook

1. Do not remove the wall mount bracket, even if you are

not using it for mounting. This provides structural

stability to the case.

2. Be sure the ceiling has adequate reinforcement to

attach a hook anchor.

3. The top of the screen case has a channel that the ceiling

hook brackets slide into. Remove the end cap on the

right end of the case and insert the brackets into the

case channel. Lock the brackets in place by tightening

two set screws. Refer to figure 3.

4. The brackets can be attached anywhere within 12" of

the end of the case.

5. Attach an S-hook or similar fastener to the large center

hole on the bracket.

INSTALLATION

SET SCREWS (2)

HOOK MOUNT

HOLE

CEILING

MOUNT

HOLES

SET SCREWS (2)

FIGURE 2

FIGURE 3

FIGURE 1

4-1/4"

5/16" 9/16"

CASE HOOK

WALL

MOUNT

BRACKET

4-5/8"

STOP SCREW

ENDCAP

SCREWS

(3)

ENDCAP

SCREWS

(3)

ELECTRICAL INSTALLATION

LOW-VOLTAGE

WALL SWITCH

INFRARED

SENSOR INPUT

MOTOR

WHITE (COMMON)

BLACK (HOT)

GREEN

GROUND TO CASE

RED

BLACK

WHITE (COMMON)

EYE AUX

120VAC 60HZ

120V WIRING DIAGRAM

WITH BUILT-IN LOW

VOLTAGE CONTROL

WHITE

RED

BLACK UP

STOP

DOWN

GROUND–MUST

BE CONNECTED

TO BUILDING

GROUND

240V WIRING DIAGRAM

WITH BUILT-IN LOW

VOLTAGE CONTROL

MOTOR

BLUE (COMMON)

BROWN (HOT)

GREEN

BLACK

BLACK (UP)

BROWN (DOWN)

BLUE (COMMON)

GROUND TO CASE

AUX EYE

240VAC 50HZ

INFRARED SENSOR

INPUT

WHITE

RED

BLACK

LOW-VOLTAGE

WALL SWITCH

STOP

DOWN

GROUND–MUST

BE CONNECTED

TO BUILDING

GROUND

BLACK

NOTE: Wired 10' Power Cord Included

SCREEN AdjUSTMENT

Screen travel is stopped automatically in the down and

up positions by the limit switches that are preset at the

factory. If it’s necessary to adjust for more or less drop

follow the steps below. The case cover must be

removed to access the motor limit switches.

Remove the case cover screw from both ends of the

screen. See figure 4. Be sure to hold the cover while

removing the screws.

Rotate the cover up and away from the case until it can

be removed.

SETTING THE DOWN LIMIT POSITION

TO REDUCE SCREEN DROP:

Turn the red limit switch screw clockwise to

decrease the amount of screen drop. Run the

screen down to test the stop position. If the

screen drops too far, raise the screen about one

foot and adjust the limit switch again. Repeat

until the desired position is set.

TO INCREASE SCREEN DROP:

Turn the red limit switch screw counterclockwise

to increase the amount of screen drop. Run the

screen down to test the stop position. If the

screen does not drop enough, raise the screen about one foot and adjust the limit switch again. Repeat

until the desired position is set.

CAUTION: Do not adjust for more drop than what was ordered. At least 1-1/2 wraps of fabric must remain on the roller.

This screen comes standard with 0" or 2" black at the top. See the specification data sheet for details.

CASE COVER

SCREW

FIGURE 4

HOOK

FIGURE 5

ROTATE UP

TROUBLESHOOTING

SYMPTOM

1. Screen will not operate.

Motor does not hum.

2. Incorrect stopping position in

downward direction.

3. Incorrect stopping position in

upward direction.

4. Noise.

NOTE: Screen will operate with a

low pitched hum.

5. Coasting.

CAUSE

(a) Incorrect line voltage.

(b) Blown fuse.

(d) No power to operating switch

or junction.

Power at junction box

(e) Thermal overload tripped.

(f) Broken wire in the “down” or “up”

position.

(g) Defective motor, limit switch or

capacitor.

(h) Capacitor burned out.

(a) Lost roller wrap.

(b) “Down” limit switch out of

adjustment

(a) Lost roller wrap.

(b) “Up” limit switch out of

adjustment

(a) Gear Noise.

(a) Defective brake.

SOLUTION

(a) Verify 115-125V (or 220-240V). If

insufficient voltage, rewire

incoming electric line.

(b) Replace fuse.

(d) Check above. Tighten all loose

wire connections. Correct any

improper connections.

“Down” Position

Check for power across black

and white leads.

“Up” Position

Check for power across red

and white leads.

(e) Let motor cool down for 15

minutes. Try again.

(f) Check for continuity. Cut off old

splice and reconnect.

(g) Replace motor assembly.

NOTE: Motor is a sealed assembly.

(h) Replace motor assembly.

(a) See instructions below.

(b) See installation instructions.

(a) See instructions below.

(b) Adjust “up” limit switch. Call for

information

(a) Replace motor assembly.

Visit www.da-lite.com/products/tutorials.php to find installation and troubleshooting tutorials. You will also

find a link to Live Chat for interactive support and you can contact us by email at [email protected] or by phone

at (800) 622-3737 or (574) 267-8101 with any troubleshooting questions.

RESTORING LOST ROLLER WRAP

1. Tape a strap to the bottom of the screen surface.

2. Push strap over back of roller.

3. Feed fabric as you pull strap to draw fabric over top of roller.

4. Remove tape and strap.

THIS PAGE IS INTENTIONALLY LEFT BLANK

Printed in U.S.A. 99620 Rev. 6/08

LIMITED ONE YEAR WARRANTY

ON DA-LITE PRESENTATION PRODUCTS

Da-Lite Screen Company, Inc. warrants its products to the original purchaser only, to be free from

defects in materials and workmanship for a period of one (1) year from the date of purchase by

the original purchaser provided they are properly operated according to Da-Lite’s instructions and

are not damaged due to improper handling or treatment after shipment from the factory.

This warranty does not apply to equipment showing evidence of misuse, abuse or accidental

damage, or which has been tampered with or repaired by a person other than authorized Da-Lite

personnel.

Da-Lite’s sole obligation under this warranty shall be to repair or to replace (at Da-Lite’s option)

the defective part of the merchandise. Returns for service should be made to your Da-Lite

dealer. If it is necessary for the dealer to return the screen or part to Da-Lite, transportation

expenses to and from Da-Lite are payable by the purchaser and Da-Lite is not responsible for

damage in shipment. To protect yourself against damage or loss in transit, insure the product and

prepay all transportation expenses.

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,

INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANT ABILITY. Any

implied warranties of fitness for use, or merchantability, that may be mandated by statute or

rule of law are limited to the one (1) year warranty period. This warranty gives you specific

legal rights, and you may also have other rights, which vary from state-to-state. NO LIABILITY

IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN

OPERATION OF EQUIPMENT, OR FOR INCIDENTAL, DIRECT, OR CONSEQUENTIAL

DAMAGES OF ANY NATURE.

In the event that there is a defect in materials or workmanship of a Da-Lite product, you may

contact our Sales Partners at PO Box 137, Warsaw, IN 46581-0137, (574) 267-8101, (800) 622-

3737.

IMPORTANT: THIS WARRANTY SHALL NOT BE VALID AND DA-LITE SHALL NOT BE

BOUND BY THIS WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH

DA-LITE’S WRITTEN INSTRUCTIONS.

Keep your sales receipt to prove the date of purchase and your original ownership.

Inhaltsverzeichnis

Andere Da-Lite Projektionsfläche Handbücher

Da-Lite

Da-Lite ASCENDER ELECTROL Bedienungsanleitung

Da-Lite

Da-Lite Cosmopolitan Electrol Bedienungsanleitung

Da-Lite

Da-Lite LARGE ADVANTAGE DELUXE ELECTROL Bedienungsanleitung

Da-Lite

Da-Lite Large advantage electrol Bedienungsanleitung

Da-Lite

Da-Lite MULTI-MASK IMAGER Bedienungsanleitung

Da-Lite

Da-Lite Large Cosmopolitan Electrol Bedienungsanleitung

Da-Lite

Da-Lite TENSIONED EXECUTIVE ELECTROL Bedienungsanleitung

Da-Lite

Da-Lite Cosmopolitan Electrol Bedienungsanleitung

Da-Lite

Da-Lite ADVANTAGE DELUXE ELECTROL Bedienungsanleitung

Da-Lite

Da-Lite Deluxe Insta-Theater Bedienungsanleitung

Da-Lite

Da-Lite TENSIONED EXECUTIVE ELECTROL Bedienungsanleitung

Da-Lite

Da-Lite ADVANTAGE DELUXE ELECTROL Bedienungsanleitung

Da-Lite

Da-Lite Model C Bedienungsanleitung

Da-Lite

Da-Lite STUDIO ELECTROL Bedienungsanleitung

Da-Lite

Da-Lite PROFESSIONAL ELECTROL Bedienungsanleitung

Da-Lite

Da-Lite Slimline Electrol Bedienungsanleitung

Da-Lite

Da-Lite senIor electrol Bedienungsanleitung

Da-Lite

Da-Lite TENSIONED HORIZON ELECTROL Bedienungsanleitung

Da-Lite

Da-Lite Picture King Bedienungsanleitung

Da-Lite

Da-Lite electrol Bedienungsanleitung

Da-Lite

Da-Lite Tensioned Advantage Deluxe Electrol Series Bedienungsanleitung

Da-Lite

Da-Lite IDEA Screen Bedienungsanleitung

Da-Lite

Da-Lite Da-Snap 74610 Bedienungsanleitung

Da-Lite

Da-Lite DesIgner Contour Manual Bedienungsanleitung

Beliebte Projektionsfläche Handbücher anderer Marken

Draper

Draper E Series Handbuch

Elite Screens

Elite Screens Elite Tripod Series Bedienungsanleitung

Laarhoven

Laarhoven Companion II Bedienungsanleitung

Renogy

Renogy RMS-LFPS-US Bedienungsanleitung

Samsung

Samsung S*H65* Bedienungsanleitung

FONESTAR

FONESTAR PPTR-43100-FA Bedienungsanleitung

Slide Clear

Slide Clear Varro XL Bedienungsanleitung

Elite Screens

Elite Screens M85XWS1-SRM Bedienungsanleitung

OS РХ-090Н Bedienungsanleitung

Niko

Niko 10-845 Bedienungsanleitung

Speaka Professional

Speaka Professional 2357532 Betriebsanleitung

Sima

Sima XL-72 Bedienungsanleitung

Jasic

Jasic EVO 2.0 ET-200P Bedienungsanleitung

Elite Screens

Elite Screens Starling 2 Series Bedienungsanleitung

InFocus

InFocus SC-WALL GRY-92H Handbuch

Barco

Barco OverView MVL-615 Bedienungsanleitung

Draper

Draper Envoy Handbuch

FART PRODUKT

FART PRODUKT Standard SCREEN Bedienungsanleitung