Daikin E8.5064 Bedienungsanleitung

E8.5064 V1

System Manager

Installation Manual

Please observe the safety instructions and

read through this manual carefully before

commissioning the equipment.

Safety information General information

General infor mation

Safety information

Power connection regulations

Please note the connection conditions specified by your

local electrical power supply company and the VDE regula-

tions.

Your heating control system may only be installed and ser-

viced by appropriately authorised specialists.

E For fixed devices, a facility for mains disconnection in

accordance with EN 60335 must be installed in compliance

with the installation specifications (e.g. switch).

EThe mains lines insulation must be protected against damage

caused by overheating (e.g. insulation hose).

EThe minimum distance to installation objects in the vicinity

must be chosen so that the permitted ambient temperature is

not exceed during operation (see table - Technical Data).

EIf the system is not installed properly, persons using it are at

put at risk of fatal or serious injury (electric shock).

Ensure the controller is de-energized prior to performing any

work on the controller!

Safety

Please read and keep in a safe place

Please read through these instructions care-

fully before installing or operating. Following the installa-

tion, pass the instructions on to the operator.

Warranty conditions

If the system is not installed, commissioned, serviced and

repaired properly, it will render the manufacturer's warranty

null and void.

Conversion

All technical changes are prohibited.

Transport

On receipt of the product, check that the delivery is com-

plete. Report any transport damage immediately.

Storage

Store the product in a dry place. Ambient temperature: see

Technical data.

Important text passages

!Important information is highlighted by an

exclamation mark.

EThis attention symbol indicates dangerous situations.

Note

!The operating manual describes the maximum

version of the controller, meaning that not all

statements are relevant for your device.

General information Description

General Notes

With regard to installation, operation, and maintenance,

the following instructions must be observed. This

device must only be installed by a specialist technician.

Improperly performed repairs can subject users to

considerable risks.

To comply with applicable regulations, the instructions

for assembly and operation must be readily available at

all times and must be handed over to the responsible

engineer when working on the device for his attention.

Description

Declaration of conformity

We the manufacturer declare the product E8.5064 is in

conformity with the fundamental requirements of the follow-

ing directives and standards.

Directives:

– 2004/108/EC, 2006/95/EC

Standards:

– EN 60730-1, EN 60730-2-9

The manufacture is subject to the quality management

system in accordance with DIN EN ISO 9001.

Function

The device contains a number of functions and must be

set in accordance with use. The following functions are

mapped in the System Manager:

Cascade modulating HS

Cascade switching HS

Control of 2 HS or 2-stage HS via relay

Water heating, 2 mixed heating circuits, as well as 2

extra functions

Demand-related circulation pump control

Automatic toggle between summer and winter time

Activation of a timer is possible

Inhaltsverzeichnis General information

Inhaltsverzeichnis

General information 2

Safety information 2

Safety 2

General Notes 3

Description 3

Declaration of conformity 3

Function 3

Inhaltsverzeichnis 4

Installation 6

Assembly/Dismantling 6

Electrical Connection 7

Connecting instructions 7

Connection diagram 8

Terminal assignment 9

Power terminal assignments 10

Sensor terminal assignments 11

Remote controls 13

Operation-control module Merlin BM, BM 8,

Lago FB 13

Remote control FBR2 13

Sensor resistances FBR 14

DCF receiver 14

PC 14

Maximum delimiter 15

Telephone switch 15

Sensor values/characteristic curve 16

Sensors 17

Outside sensor AF (AFS) S17

Immersion sensor KF (KFS) H/SPF (SPFS) F17

Strap-on sensor VF (VFAS) v17

System bus 18

The heating system 18

Bus ID 18

Input of the basic setting 18

Operation in normal mode 18

Operating elements 18

ÇOperating mode selection 19

Effect of the operating mode 19

Display in normal operation 20

Changing set values 21

Operating elements 21

Operating level 22

Areas 23

General 23

Display 23

User 23

Time programs 23

Expert 23

Expert FA (only for FA via BUS) 23

Levels 23

Installation 23

Hot water 23

Heating circuit I/II 23

Solar/MF 23

General information Inhaltsverzeichnis

Installation level 24

Commissioning procedure 24

Installation (selecting basic controller functions) 24

BUS-ID HS (- - - -) 25

HS 1 TYPE (primary heat generator type) 25

HS1 BUS (connection for HS) 25

HS 2 TYPE

(secondary heat generator type HS => A7) 25

STORAGE HS2 (heat accumulator for HS2) 25

BUFFER (heater buffer storage type) 26

HC FUNCTION

(heating circuit function selection) 26

CAP/STAGE (boiler output for each stage) 27

Auxiliary relay functions 28

RELAY FUNC 1 (function selection relay MF1) 28

T-MF1 SETP

(switching temperature relay MF1) 28

MF 1 HYST (hysteresis relay MF1) 28

F15 FUNCTION (sensor function F15) 31

BUS ID (heating circuit number): 31

5 K SENSORS/1 K SENSORS 31

Choice of installation 32

Schematic circuit diagrams hydraulic system 32

Installation 01 = E8.4034

=> Cascade controller for modulating HS 32

Terminal assignment 33

Installation 02 = E8.4834

=> Cascade controller for switching HS 34

Terminal assignment 35

Installation 03 = E8.3611 => 0 - 10 V Controller 36

Terminal assignment 37

Installation 04 = E8.0634

=> Standard controller with 2-stage HS 38

Terminal assignment 39

Installation 05 = 2HS controller

=> 2 HS cascade switched via relay 40

Terminal assignment 41

Service 42

Error Messages 42

Troubleshooting 43

Dimensions 45

Technical Data 46

Glossary 47

Assembly/Dismantling Installation

Installation

Assembly/Dismantling

Sketch showing basic mode of operation:

A Controller, side view, cutaway view

B Control panel plate

C Mounting clamp

D Unlocking holes (see Chapter Changing set values)

E Sharp-pointed tool

Installing the controller:

1. Set the mounting clamp to the wall thickness of the con-

trol panel (at the left and right-hand side of the unit):

a. Pull the mounting clamp at the low away from the con-

troller wall (toothing).

b. In this condition, slide the mounting clamp down or up

until the distance from the edge of the unit corre-

sponds to the thickness of the control panel wall.

Detent position 1 0.5 - 1.0 mm wall thickness

Detent position 5 5.0 mm wall thickness

c. Press the mounting clamp against the controller wall at

the low.

2. Press the controller into the control panel recess and

check that it is firmly secure. If the controller wobbles: Re-

move the controller and move the mounting clamps up.

Installation Electrical Connection

Removing the controller:

EDisconnect the unit from the power supply before

removing it.

d) Insert a sharp-pointed tool at an angle with respect to

the exterior wall into one of the unlocking holes (the

tool must be slid between mounting clamp and control

panel wall).

e) Lever the tool with respect to the unit exterior wall.

This causes the mounting clamp to release the control

panel wall.

Raise the unit slightly at the corresponding side and repeat

the procedure on the other side of the unit.

The unit can now be removed.

Electrical Connection

Connecting instructions

EThe controller is designed for an operating voltage of

230 V AC at 50 Hz. The burner contact is potential-free

and must always be connected in series with the

mechanical boiler thermostat (if present).

EImportant: Bus lines and sensor lines must be laid

separately, away from mains cables!

!After connecting or modifying the connections of

sensors and remote controls the controller must be

briefly switched off (mains switch/fuse). The function

of the controller is reconfigured in accordance with

the connected sensors the next time the controller is

switched on.

Note for installation in connection with digital room

device

When installing a digital room device, the heating circuit-

specific set values are adjusted at the room device. These

values are automatically superceeded inside the controller.

!If during operation the digital room device is

separated from the BUS for a longer time period

(>5 min), the heating controller will continue to work

with its own set values.

In order to avoid damages in case of errors - for deviations

from relevant set values (such as maximum flow tempera-

ture for floor heaters) - we suggest the following proce-

dure:

1. Installing the new heating controller

2. Set all values for heating controller

3. Install one digital room device

4. Set all values for digital room device

Electrical Connection Installation

Connection diagram

~ 230 V; Relay switching capacity 2 (2) A, ~ 250 V

Installation Electrical Connection

Terminal assignment

Sensors

VII (1+2): eBUS (FA) or 0 - 10 V output

I (1,2,3+ ):F1/F2/F3 = buffer storage tank

low/middle/top

I (2+3+ ): FBR2 (FBR1) for heating circuit 1

I (2+ ): F2 = Room sensor for heating circuit 1

I (4+5): F5 = Flow sensor heating circuit 2

I (6+7): F6 = Storage tank sensor

I (7+8): F8 = Boiler sensor/header sensor

I (9+10): F9 = Outdoor sensor

V (1+ ): F11 = Flow sensor heating circuit 1/

Multifunction relay sensor 1

V (2+ ): F12 = Hot-water tank low/

Multifunction relay sensor 2

VIII (1+ ): F13 = PT1000 => HS2/collector 2/

Multifunction relay sensor 3

VIII (2+ ): F14 = PT1000 => Collector 1/

Multifunction relay sensor 4

III (1-3): FBR2 (FBR1) for heating circuit 2

III (1+2): F15 = 0-10V input/light sensor/

Room sensor for heating circuit 2

III (2+3): F17 = Pulse counter for output

measurement

IX (1+2): Data line CAN bus

IX (3+4): Power supply CAN bus

Mains

II (1): Neutral conductor, mains

II (2): Power supply, unit

II (3): Power supply, relay

II (4): A1 = Pump heating circuit 1

II (5): A1 = Pump heating circuit 2

II (6): A3 = Cylinder charging pump

II (7): A4 = Mixer motor heating circuit 2 on

II (8): A5 = Mixer motor heating circuit 2 to

II (9+10): A6 = Burner stage 1/HS 1

VI (1+2): A7 = Burner stage 2/HS 2/Solid fuel

IV (1): A8 = Mixer motor heating circuit 1 on/

Multifunction relay

IV (2): A9 = Mixer motor heating circuit 1 to/

Multifunction relay

IV (3): A10 = Collector pump 2/Switching valve to

solar tank 2/Multifunction relay 3

IV (4): A11 = Collector pump 1 (ON / OFF)

multifunction relay

EImportant: Bus lines and sensor lines must be laid separately, away from mains cables!

Electrical Connection Installation

Options

Provided no separate reg-

ulations for protecting the

relay apply, a bridge to

supply the relay must be

connected between termi-

nals II 2 and II 3.

Power terminal assignments

Plug 2 [II]

Plug 6 [VI]

Plug 4 [IV]

N: Neutral conductor, mains

L1: Power supply, unit

L1´: Power supply to relay

D1: heating circuit pump HC 1

D2: heating circuit pump HC 2

F: Storage tank charging pump

v: Mixer open, heating circuit 2

v: Mixer closed, heating circuit 2

H: Burner stage 1

H: Burner stage 2/HS2

v: Mixer heating circuit 1 open / Multifunction relay 1

v: Mixer heating circuit 1 close / Multifunction relay 2

Collector pump 2/Switching valve / Multifunction relay 3

Collector pump 1(ON / OFF) / Multifunction relay 4

Inhaltsverzeichnis

Andere Daikin Steuereinheit Handbücher

Daikin

Daikin BRC1E62 Bedienungsanleitung

Daikin

Daikin EKCBX008BBV3 Bedienungsanleitung

Daikin

Daikin IM 837-2 Handbuch

Daikin

Daikin SV1A25AJV1B Bedienungsanleitung

Daikin

Daikin E2MV03B6 Bedienungsanleitung

Daikin

Daikin EK2CB07CAV3 Bedienungsanleitung

Daikin

Daikin FWB-CT Bedienungsanleitung

Daikin

Daikin Myzone 3 Handbuch

Daikin

Daikin ACZ Handbuch

Daikin

Daikin Home Controls EKRMIBEV1V3 Bedienungsanleitung

Daikin

Daikin BACnet MT3041 Bedienungsanleitung

Daikin

Daikin BRC1E71 Bedienungsanleitung

Daikin

Daikin E2MV107A6 Bedienungsanleitung

Daikin

Daikin RoCon BF Bedienungsanleitung

Daikin

Daikin 4PW72362-1-21 Bedienungsanleitung

Daikin

Daikin EKCB07CAV3 Bedienungsanleitung

Daikin

Daikin Altherma ESBE Bedienungsanleitung

Daikin

Daikin BRC230Z4 Bedienungsanleitung

Daikin

Daikin Rotex RoCon G1 Bedienungsanleitung

Daikin

Daikin EKWUFHTA1V3 Bedienungsanleitung

Daikin

Daikin EK2MV2B10C5 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung