Danbit KAM-IP2MP-PT Bedienungsanleitung
H.264 Pan/Tilt Dome Network Camera
Quick Installation Guide
This guide describes the basic functions of
Pan/Tilt Dome Network Camera.
All detailed information is described in the user’s manual.
Before Install
◎Power off the Network Camera as soon as it is found smoking or smelt
unusual.
Contact your distributor when such cases happen.
◎Keep the Network Camera away from the water. If the Network Camera is
wet, power off immediately.
Contact your distributor when such cases happen.
◎ Do not place the Network Camera around the heat sources, such as
television or oven.
◎ Refer to your user’s manual for the operating temperature.
◎ Keep the Network Camera away from the direct sunlight.
◎ Do not place the Network Camera in high humid environments.
1
◎ Do not place the Network Camera on unsteady surfaces.
◎ Do not touch the Network Camera when it’s lightening.
◎ Do not disassemble the Network Camera.
◎ Do not drop the Network Camera.
◎ Do not manually pan and tilt the Network Camera when are power is on.
◎ Do not insert any object into the Network Camera, such as needles.
2
1. Package contents
◎ TheNetworkCamera ◎Quick Installation Guide
(Wire or PoE model)
◎ Power adapter ◎Camera stand
◎ Software CD
3
2. Hardware description
◎ Panel
Infrared LEDs
External microphone
USB Socket
Audio Jack
Power Jack
LAN Socket SD Socket
Indicating LEDs
General I/O terminal block
4
3. Install your Network Camera in Ethernet network
1. Use Ethernet cable to make connection from Ethernet port to the hub.
* Use Category 5 Cross Cable when the Network Camera is directly connected
to PC.
2. Finally, connect power cord to a power outlet.
◎ Using a PoE-enabled switch
The Network Camera is PoE-compliant, allowing transmission of power and
data via a single Ethernet cable. Follow the below illustration to connect the
Network Camera to a PoE-enabled switch via Ethernet cable.
5
4. Assign IP address
1. Install “IP Finder” under the software utility directory from software CD.
2. Execute “IP finder” and do with the following method.
First, press the “Search Camera” button.
Second, press the “Start Find” button in the next setting page.
Third, select a row and double click at the “IP” column to open the browser.
The home page of the device will be shown after a few moment.
For detail setup and further configuration, please check user’s
manual on the software CD.
6
5. Connects to the Network Camera
For detail setup and further configuration, please check user’s
manual on the software CD.
7
6. ip-discovery.com(Free DDNS service)
When you want to connect the network camera over Internet, you can use the
service “ip-discovery.com”. The “ip-discovery.com” is a free DDNS server for
this camera. Make sure that the router must start UPnP and DHCP server
functions. You can get the domain name which you wish very easily after
registration. In Network page—DDNS settings of this camera, you just input
the host name you want and your e-mail address, and click “Register”, then
you can have the hostname for this camera not longer than 20 seconds if the
DDNS registration result is OK. Then you can connect to this ip camera by
*http://XXX.ip-discovery.com:@@@@
*XXX: the host name you type
*@@@@: the HTTP port (get it automatically by ip-discovery server)
User password: Default the password is last six number of the MAC. To
change “root” password at “Security configuration” can change the user
password, This “User password” is entered in the ip-discovery.com Password.
Note: You must set the ports between your router and camera manually if the
registration is failed.
For detail setup and further configuration, please check user’s
manual on the software CD.
8
7. Client Settings
(1) For the initial access to the Network Camera in Windows, the web browser may
prompt for permission to install a new plug-in for the Network Camera. This plug-in
has been registered for certificate and is used to display the video in the browser.
Users may click on to proceed.”
1. Click “Install” and “Run” ActiveX controls
2. Refresh IE Browser, a question frame will pop-up to ask for download Active-X. press
“Run”.
Note: Currently the Network Camera utilizes 32-bit ActiveX plugin. You CAN NOT
open a management/view session with the camera using a 64-bit IE browser.
9
Inhaltsverzeichnis
Andere Danbit Sicherheitskamera Handbücher
