Danby DAC050BACWDB Montageanleitung

2016.11.14

AIR CONDITONER

CLIMATISEUR

DAC050BACWDB / DAC050BAUWDB

OWNER’S USE AND CARE GUIDE

GUIDE D’UTILISATION ET D'ENTRETIEN

MODEL • MODÈLE

DANBY PRODUCTS LIMITED, ONTARIO, CANADA N1H 6Z9

DANBY PRODUCTS INC., FINDLAY, OHIO, USA 45840

AIR CONDITIONER

Owner’s Use and Care Guide ................................

• Welcome

• Important Safety Information

• Features

• Installation Instructions

• Operation Instructions

• Care and Maintenance

• Troubleshooting

• Warranty

CLIMATISEUR

Guide d’utilisation et d’entretien du propriétaire....

• Bienvenue

• Consignes de sécurité importantes

• Caractéristiques

• Consignes d’installation

• Consignes d’utilisation

• Soins et entretien

• Dépannage

• Garantie

CONTENTS

Model • Modèle • Modelo

DAC050BACWDB / DAC050BAUWDB

CAUTION:

Read and follow all safety rules and operating

instructions before ﬁrst use of this product.

PRÉCAUTION :

Veuillez lire attentivement les consignes de

sécurité et les instructions d’utilisation avant

l’utilisation initiale de ce produit.

TABLE DES MATIÈRES

ÍNDICE

1-10

11-20

This product is factory equipped with a power supply cord that has a three-pronged grounded plug. It must

be plugged into a mating grounding type receptacle in accordance with the National Electrical Code and

applicable local codes and ordinances. If the circuit does not have a grounding type receptacle, it is the

responsibility and obligation of the customer to exchange the existing receptacle in accordance with the

National Electrical Code and applicable local codes and ordinances. The third ground prong should not,

under any circumstances, be cut or removed. Never use the cord, the plug or the appliance when they show

any sign of damage. Do not use your appliance with an extension cord unless it has been checked and test-

ed by a qualiﬁed electrician or electrical supplier.

IMPORTANT - GROUNDING METHOD

Ce produit arrive d’origine avec un cordon d’alimentation équipé d’une prise à trois ﬁches. Il doit être

branché dans une prise avec une ﬁche de mise à la terre en conformité avec le Code national de l’électricité

et les codes et règles locaux applicables. Si la prise murale n’a pas de mise à la terre, il est de la

responsabilité et l’obligation du client de changer la prise existante pour la rendre conforme au Code

national de l’électricité et aux codes et règles locaux applicables. La ﬁche de mise à la terre ne doit pas, en

aucune circonstance, être coupée ou retirée. Si vous apercevez des signes de dommage, n’utilisez jamais le

cordon d’alimentation, la prise ou l’appareil. N’utilisez jamais l’appareil avec une rallonge sauf si elle a été

vériﬁée et testée par un électricien qualiﬁé ou un fournisseur de matériel électrique.

IMPORTANT - MÉTHODE POUR LA MISE À LA TERRE

WELCOME

Welcome to the Danby family. We are proud of our quality products, and we believe in dependable service, like you will

ﬁnd in this Owner’s Use and Care Guide, and like you will receive from our friendly customer service department. Best of

all, you will experience these values each and every time you use your Danby appliance. That is important, because your

new appliance will be a part of your family for a long time.

For easy reference, we suggest you attach a copy of your sales slip/receipt to this page, along with the following

information, located on the manufacturer’s nameplate on the right side of the unit above the powercord.

Note the information below; you will need this information to obtain service under warranty.

NOTE: TO RECEIVE WARRANTY SERVICE YOU MUST PROVIDE A VALID PROOF OF PURCHASE.

NOTE: THIS UNIT IS NOT DESIGNED FOR “THROUGH-THE-WALL” INSTALLATION.

Model No:

Serial No:

Date Purchased:

NEED HELP?

Before you call for service, here are a few things you can do to

help us serve you better:

Read this Owner’s Use and Care Guide:

It contains instructions to help you use and maintain your

appliance properly.

If you received a damaged appliance:

Immediately contact the retailer (or builder) that sold you the

appliance.

Save time and money:

Check the Troubleshooting section at the end of the guide

before calling. This section helps you solve common problems

that may occur.

If you do need service, you can relax, knowing help is only a

phone call away.

WARNING

Improper connection of the grounding plug can result in risk of

ﬁre, electric shock and/or injury to persons associated with the

appliance. Check with a qualiﬁed service representative if in doubt

that the appliance is properly grounded.

1-800-26-

(1-800-263-2629)

1. All wiring must comply with local and national electrical codes and must be installed by a qualiﬁed electrician. If you

have any questions regarding the following instructions, contact a qualiﬁed electrician.

2. Check available power supply and resolve any wiring problems BEFORE installing and operating this unit.

3. This 115V air conditioner uses 4.8 or less nameplate amps and may be used in any properly wired, general-purpose

household receptacle. See Table 1 for the speciﬁcations for the individual branch circuit.

4. For your safety and protection, this unit is grounded through the powercord plug when plugged into a matching wall

outlet. If you are not sure whether your wall outlet is properly grounded, please consult a qualiﬁed electrician.

5. The wall outlet must match the 3-prong plug on the service cord supplied with the unit. DO NOT use plug adapters.

See Table 2 for receptacle and fuse information.

6. The rating plate on the unit contains electrical and other technical data. The rating plate is located on the right side of

the unit, above the powercord.

ELECTRICAL

REQUIREMENTS

TABLE 1

Suggested Individual Branch Circuit

Nameplate Amps

4.8 *AWG Wire Size

AWG- American Wire Gauge

*Based on copper wire at 60°C temperature rating

TABLE 2

Receptacle and Fuse Types

Rated Volts 125

Amps 15

Wall Outlet

Fuse Size 15

Time Delay Fuse Plug Type

(or Circuit Breaker)

IMPORTANT SAFETY INFORMATION

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

FOR YOUR SAFETY: Read these instructions carefully before operating the unit.

FEATURES

Your appliance is designed to be highly efﬁcient in energy savings. Follow these recommendations for greater efﬁ-

ciency.

1. Select a thermostat setting that suits your comfort needs and leave at that chosen setting.

2. The air ﬁlter is very efﬁcient in removing airborne particles. Keep the air ﬁlter clean at all times. (Usually cleaned every

2 weeks depending on indoor air quality.)

3. Use drapes, curtains or shades to keep direct sunlight from penetrating and heating the room, but do not allow drapes

or curtains to obstruct the air ﬂow around the unit.

4. Start your air conditioner before the outdoor air becomes hot, to avoid an initial period of discomfort while the unit is

cooling the room.

IMPORTANT SAFETY INFORMATION

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

FOR YOUR SAFETY: Read these instructions carefully before operating the unit.

ENERGY

SAVING TIPS

Air Filter

Cabinet

Air Filter

Exterior

Air Inlet

Interior Air Inlet

Control Panel

Interior Air Outlet

INSTALLATION INSTRUCTIONS

TOOLS NEEDED FOR INSTALLATION:

• Screwdrivers: Phillips and ﬂat head.

• Power Drill: 1/8” (3.2mm) diameter drill bit

• Pencil

• Measuring Tape

• Scissors

• Carpenter’s Level

NOTE: Save the shipping carton and packing materials for future storage or transportation. From

the carton, remove the plastic bag containing the installation hardware kit necessary for the in-

stallation of your air conditioner. Please check the contents of the hardware kit against the corre-

sponding model check list, prior to installation of the unit. See Fig. 1.

ELECTRIC SHOCK HAZARD

To avoid the possibility of personal

injury, disconnect power to the unit

before installing or servicing.

NOTE: Your RoomAir Conditioner is designed for easy

installation in a single or double-hung window. This unit

is NOT designed for vertical (slider type) windows and/or

through-the-wall applications.

Because the compressor is located on the controls side of the unit (left side), this side

will be heavier and more awkward to manipulate. Inadequate support on control side of

the unit can result in personal injury and damage to your unit and property. Therefore, it

is recommended that you have someone assist you during the installation of this unit.

CAUTION

INSTALLATION

HARDWARE

1/2in. (13 mm)

screws (7) Safety Lock (1)

3/8in. (9.5mm) screws

(4) *Factory installed

on some models

“L” Shaped

mounting

bracket (1)

* Factory installed

on some models

Sash bracket (2)

Adhesive

Foam Seal(1)

Side Curtain LH (1)

Side Curtain RH (1)

Regular

Foam Seal(1)

Foam insert

2 pieces

Weather-stripping

(5)

Fig. 1

1. This room air conditioner is designed to ﬁt easily into a single or double hung window. However, since window designs

vary, it may be necessary to make some modiﬁcations for safe, proper installation.

2. Make sure window and frame are structurally sound and free from dry and rotted wood.

3. For maximum efﬁciency, install the air conditioner on a side of the house or building which favours more shade than

sunlight. If the unit is in direct sunlight, it is advisable to provide an awning over the unit.

4. Provide sufﬁcient clearance around the cabinet to allow for ample air circulation through the unit (See Fig. 2). The

rear of the unit should be outdoors. It should not be in a garage, or inside a building. Keep unit as far away as possi-

ble from obstacles/obstructions and at least 30” above the ﬂoor or ground. Curtains and other objects within the room

should be prevented from blocking the air ﬂow.

5. Be certain that the proper electrical outlet is within reach of the installation. Use only a single outlet circuit rated at 15

amps. All wiring should be in accordance with local and national electrical codes.

6. DO NOT install unit where leakage of combustible gas is suspected. Your air conditioner may fail to operate in air

containing oils (including machine oils), sulﬁde gas, near hot springs, etc.

NOTE: Your unit is designed to evaporate condensation under normal conditions. However, under extreme humidity con-

ditions, excess condensation may cause basepan to overﬂow to the outside. The unit should be installed where conden-

sation run-off cannot drip on pedestrians or neighbouring properties.

NOTE: It is normal for your unit to drip a small amount of water, especially on excessively humid days.

INSTALLATION INSTRUCTIONS

LOCATION

Awning

Fence,

wall, or

other

obstacle

Ground

Side

Obstruction

20 in.

(50.8 cm)

Min

30 in. (76.2 cm)

Min

12 in. (30.5 cm) Min

20 in.

(50.8 cm)

Fig. 2

INSTALLATION INSTRUCTIONS

ASSEMBLY AND

INSTALLATION

1. Assembly of the upper channel to the cabinet (factory installed on some units).

• “L” Shaped Top Channel: install the “L” shaped channel to the top of the cabinet as shown in Fig. 3, using four (4) 3/8”

screws.

2. Assembly of the side curtains to the cabinet.

• Extend the shutter from the shutter frame and slide it into the shutter tabs on the side channel of the air conditioner,

as shown in Fig. 4.

• Slide the shutters into the top (“L” shaped) and bottom (“U” shaped) channels. The shutters are identiﬁed (on frame)

as left and right.

3/8” screws

“L” shaped mounting

bracket

“U” shaped Channel

(Factory Installed)

Fig. 3

Slide down into tabs

Shutter tabs

Shutter

Shutter frame

Fig. 4

3. Completing the installation.

• Carefully place the air conditioner into the window with the “L” shaped mounting bracket (on top) positioned in front

of the upper window sash. The bottom of the cabinet should be positioned on the “recessed” portion of the window

frame. Pull the window down until it rests just behind the front ﬂange of the (top) “L” shaped mounting bracket (See

Fig. 5).

• Expand the shutter frames (fully) on each side and secure the top of the frames to the window sash using one 1/2”

screw on each side and one in the “L” shaped mounting bracket (Fig. 5).

• Secure the shutter clamp on each side of the lower part of the shutter, and secure to window sill using one 1/2” screw

on each side (Fig. 5).

• Place the second foam sealing strip to ﬁt the opening between the inside and outside windows, then attach the safety

lock to the outside window frame using one 1/2” screw (See Fig. 6).

PLEASE NOTE: Window applications come in a variety of different styles. Therefore, it may be necessary to modify your

particular installation.

Window sash

“L” Shaped

Mounting

Bracket

Shutter clamps

1/2” screws

Safety Lock

1/2” screw

Foam Seal

Fig. 6Fig. 5

OPERATING INSTRUCTIONS

CONTROLS

Turn the selector switch slowly, allowing the unit to adjust.

When using THERMOSTAT, be sure to allow three minutes

before changing the temperature. Adjusting too quickly may

cause compressor to overload.

IMPORTANT

Check that the air conditioner is tilted downwards to the outside, about

3° to 4°, as shown in Fig. 7. After proper installation, condensed water

should not drain from the overﬂow drain hole during normal use. If you

notice water leaking out, check the angle of tilt, and make any neces-

sary adjustments. However, on a very humid day, water leakage can

occur – this is normal.

Measure the tilt angle from the cabinet’s edge. The distance H should

be approximately 5/8” to 3/4”.

ASSEMBLY AND INSTALLATION

Measure the tilt angle from the cabinet’s edge

WINDOW

: approximately

5/8” to 3/4”

Fig. 7

FAN SPEEDS:

• LOW FAN will circulate air at minimum speed without cooling.

• HIGH FAN will circulate air at maximum speed without cooling.

SELECTOR SWITCH: The selector switch controls cooling mode. Simply rotate the SELECTOR knob to one of the two

settings described below.

COOLING MODES:

• LOW COOL provides cooling with minimum air circulation. Recommended for night-time use.

• HIGH COOL provides cooling with maximum air circulation. Recommended for quick cooling or for extremely

hot days. Once room is cooled, reduce setting to LOW COOL.

• OFF shuts the unit down completely.

NOTE: Always allow 3 minutes before switching from one mode to another.

THERMOSTAT: The thermostat automatically controls the (compressor) cooling cycle and maintains the selected room

temperature. To set the thermostat, rotate the thermostat knob to the desired cooling setting (1 warmest - 7 coldest).

Thermostat

Selector

Switch OFF

arrêt

IMPORTANT

Control panel may not be exactly as shown. Panel can vary

depending on model purchased.

When cleaning the air conditioner be sure to turn the SELECTOR knob to the “OFF” position and disconnect the power

cord from the electrical outlet.

1. DO NOT use gasoline, benzene, thinner, or any other chemicals to clean this unit, as these substances may cause

damage to the ﬁnish and deformation of plastic parts.

2. Never attempt to clean the unit by pouring water directly over any of the surface areas, as this will cause deterioration

of electrical components and wiring insulation.

If the air ﬁlter becomes clogged with dust, air ﬂow is obstructed and reduces efﬁciency. The air ﬁlter should be cleaned

every 2 weeks.

AIR FILTER REMOVAL:

The air ﬁlter is located behind the air intake front grill. To remove the air ﬁlter, grasp the ﬁlter handle on the front of the grill

and slide it out to the right.

To reinstall the air ﬁlter, reverse the above procedures. The air ﬁlter must be vacuumed or washed by hand in warm water.

Dry thoroughly before re-installing.

CLEANING AIR FILTER:

1. Use a vacuum cleaner with soft brush attachment.

2. Wash the ﬁlter in lukewarm water below 40°C (104°F). To get best results, wash with soapy water or a neutral clean-

ing agent.

3. Rinse the ﬁlter with clean water and dry thoroughly before re-installing.

1. Turn off power and remove plug from wall socket.

2. Clean ﬁlter.

3. Store (covered) air conditioner in a dry location.

CLEANING

END OF SEASON CARE

CARE AND MAINTENANCE

IMPORTANT

DO NOT forget to install the air ﬁlter. If the air conditioner is left to operate without the air

ﬁlter, dust is not removed from the room air and may result in machine failure. When the air

inlet grill and cabinet are dirty, wipe with lukewarm water (below 40°C / 104°F). Use of a mild

detergent is recommended.

CAUTION

When installing and/or removing the air conditioner from the window, ensure that caution

is taken to prevent it from falling backward. It is recommended that installation or removal

of the air conditioner is done with assistance, to prevent injury to persons or damage to the

unit or property.

DISPOSAL

Check for local regulatory compliance regarding the approved and safe disposal of this appliance.

NOTE: In order to avoid electric shock, please turn

off the A/C and unplug the plug before mainte-

nance or repair.

AIR FILTER

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Danby Klimaanlage Handbücher

Danby

Danby DPTA090HEB1WDB Bedienungsanleitung

Danby

Danby DDR5588RHE Bedienungsanleitung

Danby

Danby DTAC100B1WDB-RF Bedienungsanleitung

Danby

Danby DAC150BBCWDB Montageanleitung

Danby

Danby DPA120HB9IBDB-6 Bedienungsanleitung

Danby

Danby Designer DPA100A1GD Montageanleitung

Danby

Danby DPAC8KDB Montageanleitung

Danby

Danby DTAC100F1WDB Bedienungsanleitung

Danby

Danby DPA140HBACBDB Bedienungsanleitung

Danby

Danby DAC050MCB3GDB Montageanleitung

Danby

Danby DAC100B6WDB Bedienungsanleitung

Danby

Danby DAC 5209M Montageanleitung

Danby

Danby DPA120DBAUGDB Bedienungsanleitung

Danby

Danby DAC120EB8WDB Bedienungsanleitung

Danby

Danby DAC5020 Bedienungsanleitung

Danby

Danby DAC080B8IWDB-6 Bedienungsanleitung

Danby

Danby DPA120E1WDB-6 Bedienungsanleitung

Danby

Danby DAC5130 Bedienungsanleitung

Danby

Danby ArcticAire APA070B1G Montageanleitung

Danby

Danby DAC5130 Bedienungsanleitung

Danby

Danby ArcticAire AAC5040 Bedienungsanleitung

Danby

Danby Silhouette DAC7024DE Bedienungsanleitung

Danby

Danby DPA135E1WDB Bedienungsanleitung

Danby

Danby Designer DPAC11012 Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung