Danby DPTA090HEB1WDB Bedienungsanleitung

DANBY PRODUCTS LIMITED, ONTARIO, CANADA N1H 6Z9

DANBY PRODUCTS INC., FINDLAY, OHIO, USA 45840

OWNER’S MANUAL

MANUEL DU PROPRIÉTAIRE

MANUAL DEL PROPIETARIO

www.Danby.com

THROUGH-THE-WALL AIR CONDITIONER

Owner’s Manual.............................1 - 11

CLIMATISEUR MURAL

Manual du propriétaire.................12 - 22

AIRE ACONDICIONADO DE PARED

Manual del propietario..................23 - 33

2019.12.11

MODEL •MODÈLE •MODELO

DPTA090HEB1WDB

DPTA120HEB1WDB

DPTA150HEB1WDB

Welcome

Welcome to the Danby family. We are proud of our quality products and we believe in

dependable service. We suggest that you read this owner’s manual before plugging in your new

appliance as it contains important operation information, safety information, troubleshooting and

maintenance tips to ensure the reliability and longevity of your appliance.

Visit www.Danby.com to access self service tools, FAQs and much more. For additional assistance

call 1-800-263-2629.

Note the information below; you will need this information to obtain service under warranty.

You must provide the original purchase receipt to validate your warranty and receive service.

Model Number: _________________________________________________

Serial Number: _________________________________________________

Date of Purchase: _______________________________________________

Need Help?

Before you call for service, here are a few things you can do to help us serve you better.

Read this owner’s manual:

It contains instructions to help you use and maintain your appliance properly.

If you receive a damaged appliance:

Immediately contact the retailer or builder that sold you the appliance.

Save time and money:

Check the troubleshooting section at the end of this manual before calling. This section

will help you solve common problems that may occur.

1-800-26- Danby

(1-800-263-2629)

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS!

ELECTRICAL REQUIREMENTS

All wiring must comply with local and national

codes and must be installed by a qualiﬁed

electrician. Check the available power supply and

resolve any wiring problems before installing and

operating this appliance.

This 230 V appliance may be used in any properly

wired, general purpose household receptacle.

The rating plate located on the right side of the

appliance just above the power cord contains

electrical and other technical data.

SAFETY INSTRUCTIONS

This appliance is not intended for use by persons,

including children, with reduced physical, sensory

or mental capabilities or lack of experience and

knowledge, unless they have been given supervision

or instruction concerning use of the appliance by a

person responsible for their safety.

Children should be supervised to ensure that they

do not play with the appliance.

Do not install the appliance where leakage of

combustible gas is suspected.

POWER CORD INSTRUCTIONS

The power supply cord contains a current device

that senses damage to the power cord. To test the

power supply cord:

1. Press the TEST button on the power supply cord.

The RESET button will click and pop out.

2. Press the RESET button until it clicks into place.

3. The power supply cord is now supplying

electricity to the appliance.

Do not use this device to turn the appliance on or

off. Ensure that the RESET button is pushed in for

correct operation. The power supply cord must be

replaced if it fails to reset when the TEST button is

pushed.

GROUNDING INSTRUCTIONS

This appliance must be grounded. Grounding

reduces the risk of electrical shock by providing an

escape wire for the electrical current.

This appliance has a cord that has a grounding

wire with a 3-prong plug. The power cord must be

plugged into an outlet that is properly grounded.

If the outlet is a 2-prong wall outlet, it must be

replaced with a properly grounded 3-prong wall

outlet.

WARNING - Improper use of the grounding

plug can result in a risk of electric shock.

Consult a qualiﬁed electrician or service agent

if the grounding instructions are not completely

understood, or if doubt exists as to whether the

appliance is properly grounded.

Do not connect your appliance to extension

cords or together with another appliance in the

same wall outlet. Do not splice the power cord.

Do not under any circumstances cut or remove the

third ground prong from the power cord. Do not

use extension cords or ungrounded (two prongs)

adapters.

If the power supply cord is damaged, it must be

replaced by the manufacturer, its service agent or

similar qualiﬁed person in order to avoid hazard.

INSTALLATION INSTRUCTIONS

DIMENSIONS

This appliance is 42 inches (106.7 cm) wide, 16

inches (40.8 cm) high and 23.9 inches (60.6 cm)

deep.

WALL SLEEVE

All wall sleeves used to install the air conditioner

must be in good structural condition and have a

rear grille that securely attaches to the sleeve or the

ﬂange of the sleeve to secure the appliance.

Install the wall sleeve according to the wall sleeve

installation instructions. When installing the sleeve

make certain there is nothing within 20 inches (50.8

cm) of the back of the appliance that would interfere

with heat radiation and exhaust air ﬂow.

INSTALLATION

1. Remove the front panel. Pull out from the bottom

to release it from the tabs and then lift up.

2. Remove the shipping screw from the vent door.

3. Rotate the vent control lever to either open or

close the vent door. When the vent control lever

is set to “close”, only the air inside the room is

circulated. When the vent control lever is set to

“open”, outdoor air will be drawn into the room.

This can reduce heating or cooling efﬁciency.

4. Lift the appliance and slide it into the wall sleeve

until it is set ﬁrmly against the front wall of the

sleeve and secure with four screws through the

ﬂange holes.

5. Reinstall the front panel. Place the tabs over the

top rail and push inward at the bottom until the

panel snaps into place.

INSTALLATION INSTRUCTIONS

DIP SWITCHES

Dip switch controls are located behind the front

panel through an opening below the control panel.

Remove the front panel to access the dip switches.

Dip switches are accessible without opening the

control box.

The appliance should be unplugged before making

adjustments to the dip switches.

DIP SWITCH CONFIGURATIONS

See the table below for dip switch conﬁgurations and functions.

UP(ON)

DOWN(OFF)

1 2 3 4 1 2 3 4

A0-

1 2 1 2 3 4

S11

Wall thermostat type

Load delay for 3 seconds

Heating type

Temperature display type

Control type

Setpoint limit 1

Setpoint limit 2

Fan CON/CYC for heating

Fan CON/CYC for cooling

Low temp. Protection

Number UP (ON) DOWN (OFF) Remarks

S1 Electric heat only Electric and pump heat Heat pump model

only

S2 Temperature display °F Temperature display °C

S3 Wall thermostat enable Control panel enable

S4*S5 UP*UP: 61°F ~ 86°F (16°C ~ 30°C)

UP*DOWN: 65°F ~ 78°F (18°C ~ 26°C)

DOWN*UP: 63°F ~ 80°F (17°C ~ 27°C)

DOWN*DOWN: 68°F ~ 75°F (20°C ~ 24°C)

Conﬁguration of S4

and S5 combine to

select set point range

S6 Fan continuous run for heating Fan cycle for heating

S7 Fan continuous run for cooling Fan cycle for cooling

S8 Low temperature protection enable Low temperature protection disable

S9 (S3

UP) Use some types of wall thermostat Use PTAC other wall thermostat Consult with

sales agent or

manufacturer for

details

S9 (S3

DOWN) Use control panel only Use control panel or some types of

wall thermostat

Sw11 Load delay for 3 seconds Normal Optional

INSTALLATION INSTRUCTIONS

DIP SWITCH CONFIGURATIONS BY PANEL CONTROL

1. Turn off the appliance.

2. Press and hold the increase and decrease buttons at the same time for 3 seconds to activate the dip

switch conﬁguration by panel control.

3. See the table below for dip switch conﬁgurations and functions by panel control.

4. The display will show two numbers. The high left number is for dip switches, the low right number is for

functions.

5. Press the increase button to set the dip switches. Press the decrease button to set the functions.

6. Press and hold the increase and decrease buttons at the same time for 3 seconds to conﬁrm choices.

The appliance will return to regular functioning after 30 seconds with no input.

Note: The LED display window will show “00” when ﬁrst entering setting mode. Set switches in sequence

one at a time.

Note: To activate front desk control function, set dip switch SW7 to “DOWN(OFF)” and then set the panel

control to “A0”.

Number High (left) Low (right) Remarks

/0 1 - by panel control 0 - by dip switches

S1 1 1 - electric heat only 0 - electric and pump heat Heat pump

model only

S2 2 1 - °F display 0 - °C display

S3*S9 3 3 - use control panel or some types of wall thermostat

2 - use some types of wall thermostat

1 - use PTAC other wall thermostat

0 - use control panel

Consult with

sales agent or

manufacturer for

details

S4*S5 4 4 - 62°F ~ 86°F (17°C ~ 30°C)

3 - 61°F ~ 86°F (16°C ~ 30°C)

2 - 65°F ~ 78°F (18°C ~ 26°C)

1 - 63°F ~ 80°F (17°C ~ 27°C)

0 - 68°F ~ 75°F (20°C ~ 24°C)

S6 6 1 - continuous fan for heating 0 - fan cycle for heating Not available

for “use PTAC

other wall

thermostat”

S7 7 1 - continuous fan for cooling 0 - fan cycle for cooling

S8 8 1 - low temperature protection

enable 0 - low temperature protection

disable Optional

SW7 A 1 - front desk control enable 0 - front desk control disable Optional

Sw11 B 1 - load delay for 3 seconds 0 - normal Optional

INSTALLATION INSTRUCTIONS

WALL THERMOSTAT TERMINAL

Note: Using a wall thermostat is optional.

Important: Only trained, qualiﬁed personnel

should access the electrical panel on the appliance

and install electrical accessories. Contact a local

electrical contractor, dealer or distributor for

assistance.

Thermostat Wire Routing

Thermostat wire is ﬁeld supplied. Recommended

wire gauge is 18 to 20 gauge solid thermostat wire.

Note: It is recommended that extra wires are run

to the appliance in case any are damaged during

installation. Thermostat wire should always be

routed around or under, never through the wall

sleeve. The wire should be routed behind the front

panel to the easily accessible terminal connector.

Pull the dip switch to the DOWN(OFF) position.

Insert the wire connector of the wall thermostat

into the relevant terminal according to the different

shapes as shown.

A: Dip switch

B: Terminal

PTAC Other Wall Thermostat

Remove the two screws as shown and take the cover

panel down.

Terminal of PTAC other wall thermostat (MODE A)

FC(L)

FC(N)

LOW-FAN

HI-FAN

4-WAY

HEAT2

HEAT1

COMP

24V(N)

24V(L)

Terminal of PTAC other wall thermostat (MODE B)

LOW-FAN

HI-FAN

4-WAY

HEAT1

COMP

24V(L)

24V(N)

Caution: Failure to follow this caution may result

in equipment damage or improper operation.

Improper wiring may damage the electronics.

Common busing is not permitted. Damage or erratic

operation may result.

FRONT DESK CONTROL

Note: Using the front desk control is optional.

The controller can handle a switch signal from

FC(L) and FC(N) input, called front desk control.

Input must be 24VAC. If the system does not receive

a 24VAC signal it will turn off; otherwise the

appliance runs in normal control.

The dip switch can control the front desk control

feature. If the dip switch is in the down position,

the appliance will turn off, otherwise it will run as

normal.

ADDITIONAL REQUIREMENTS

• Use 4-way terminal for heat pump connection

only.

• Wall thermostat must be heating changeover

4-way valve.

• For thermostats that have only one fan speed

output (on or auto) the fan speed is determined

by how the terminal connector is wired. If

low fan is desired, wire the G output from the

thermostat to (LOW-FAN) on the appliance’s

terminal block. If high fan is desired, wire the

G output from the thermostat to (HI-FAN) on the

appliance’s terminal block.

• The range of set temperature of wall thermostat

must be in consonance with the range of dip

switch setting.

• Wall thermostat must be set the type properly in

consonance with the appliance type; heat pump

or no heat pump.

• If the wall thermostat has only one electrical

heater output, connect the two terminals of

HEAT 1 and HEAT 2, the appliance can operate

two electrical heaters (only if the appliance has

two electrical heaters). Otherwise operate one

electrical heater.

• Do not remove the control panel.

• If the appliance is being controlled by a wall

mounted thermostat, place the provided cover

over the control panel as per the below.

Note: When the display shows “LC” it means the

buttons on the control panel are not available and

the appliance should be controlled by the wall

mounted thermostat that it is connected to.

INSTALLATION INSTRUCTIONS

Cette unité est contrôlée par un thermostat mural

This unit is controlled by a wall mounted thermostat

OPERATING INSTRUCTIONS

CONTROL PANEL

1. Remote control receiver

2. Display Panel: Displays the set temperature.

When in fan mode, displays the ambient

temperature. To change the temperature scale

being displayed, press and hold the up and

down buttons at the same time for three seconds.

3. Fan Button: Used to set the fan speed. The fan

can be set to low, medium, and high. The lights

will indicate the chosen fan speed.

4. Continuous fan button: In cooling mode, press

to set the fan to run continuously.

5. Increase and decrease buttons: Used to adjust

the set temperature in 1° increments.

6. Mode button: Used to choose the operating

mode. The lights will indicate the chosen mode,

cool, heat or fan.

7. Power button: Used to turn the appliance on or

off.

4 7

356

OPERATING MODES

There are three operating modes to choose from.

Press the Mode Button repeatedly to choose the

desired mode. The adjacent indicator light will

illuminate to show which mode has been selected.

• Cool Mode

Choose cool mode to set the cooling function. Use

the up and down buttons to choose the desired

temperature. When cool mode is selected, the fan

speed can be adjusted by pressing the fan button.

• Heat Mode

Choose heat mode to set the heating function. Use

the up and down buttons to choose the desired

temperature.

• Fan Mode

Choose fan mode to run the internal fan without

engaging the cooling function. Press the fan button

repeatedly to choose the fan speed, low, med or

high.

AIR FILTER

The air ﬁlter should be cleaned approximately every

2 weeks. The air ﬁlter may require more frequent

cleaning if there is signiﬁcant dander or fur in the

air.

The air ﬁlter is located behind the front intake grill.

Grasp the ﬁlter by the center and pull up and out.

Use a vacuum cleaner with a soft brush attachment

to remove any large debris or dust build up from the

air ﬁlter.

Wash the ﬁlter in lukewarm, soapy water, below

40°C (104°F), or use a neutral cleaning agent.

Rinse the ﬁlter with clean water and dry thoroughly

before reinstalling in the appliance.

Note: Do not operate the appliance without the air

ﬁlter installed.

CARE & MAINTENANCE

CLEANING

To avoid possible electric shock, ensure that the

appliance is unplugged before performing any

cleaning or maintenance.

The outside of the appliance can be wiped clean

with a soft cloth or with a lukewarm, damp cloth if

necessary.

Do not use gasoline, benzene, thinner or any

other chemicals to clean this appliance as these

substances can cause damage to the ﬁnish and

deformation of plastic parts.

Never pour water directly onto the appliance as this

will cause deterioration of electrical components

and wiring insulation.

ERROR CODES

If any of the below error codes appear on the

display, unplug the appliance and then plug it back

in. If the error code persists, call for service.

AS - room temperature sensor error

ES - evaporator temperature sensor error

CS - condenser temperature sensor error

OS - outside temperature sensor error

HS - exhaust temperature sensor error

LE - wire controller error

LO - room temperature is lower than 0°C / 32°F

HI - room temperature is higher than 37°C / 99°F

FP - low temperature protection

Andere Handbücher für DPTA090HEB1WDB

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Danby Klimaanlage Handbücher

Danby

Danby DPTA090HEB1WDB Bedienungsanleitung

Danby

Danby DAC060BBCWDB Montageanleitung

Danby

Danby DAC 6009EE Montageanleitung

Danby

Danby Diplomat DAC7037M Bedienungsanleitung

Danby

Danby Diplomat DPAC5070 Bedienungsanleitung

Danby

Danby APAC8040 Bedienungsanleitung

Danby

Danby ArcticAire AAC8504D Bedienungsanleitung

Danby

Danby DAC080EB7WDB Bedienungsanleitung

Danby

Danby DAC0100B5WDB Bedienungsanleitung

Danby

Danby DTAC100B1WDB-RF Bedienungsanleitung

Danby

Danby DAC10033TT Bedienungsanleitung

Danby

Danby DAC080EB1WDB Bedienungsanleitung

Danby

Danby DAC080B7IWDB-6 Bedienungsanleitung

Danby

Danby DPA080E3WDB-RF Bedienungsanleitung

Danby

Danby Designer DPA100A1GD Bedienungsanleitung

Danby

Danby DAC080EUB6GDB Montageanleitung

Danby

Danby Designer DPAC11012 Montageanleitung

Danby

Danby DPA100E3WDB Bedienungsanleitung

Danby

Danby DAC060EB6WDB Bedienungsanleitung

Danby

Danby DPA060B1WDB Bedienungsanleitung

Danby

Danby DPA100D1MDD Bedienungsanleitung

Danby

Danby DESIGNER DPAC10011 Montageanleitung

Danby

Danby dac10007ee Montageanleitung

Danby

Danby Designer DPA100A1GD Montageanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung