Danfoss ECL Comfort 110 Bedienungsanleitung

Operating Guide

ECL Comfort 110, application 130

(valid as of software version 1.08)

English version

www.danfoss.com

VI.KT.G6.02

2 | © Danfoss | 2016.05

How to navigate?

Safety Note

To avoid injury of persons and damages to the device, it is absolutely necessary to read and

observe these instructions carefully. The warning sign is used to emphasize special conditions

that should be taken into consideration.

This symbol indicates that this particular piece of information should be read with

special attention.

Adjust temperatures and values.

Switch between menu lines.

Select / return.

2 sec.

Return to daily user menu.

What do the symbols mean?

Mode COMFORT<

Temp. 48@½

1000

The desired ow temperature is inuenced by for example return temperature.

The actuator closes the control valve.

The actuator opens the control valve.

The actuator does not activate the valve.

The pump is ON.

The pump is OFF.

The controller is in setback mode.

The controller is in pre-setback mode (the symbol is blinking).

The controller is in comfort mode.

The controller is in pre-comfort mode (the symbol is blinking).

VI.KT.G6.02 © Danfoss | 2016.05 | 3

Table of contents

Table of contents Line Page

Weather compensated ow temperature control of heating and boiler systems

User guide, installation & maintenance

Introduction 5

Settings overview 6

Daily use 7

Temperatures 7

Select control mode 8

Set your personal schedule 8

Maintenance 10

Date - time 1000 10

Flow temp. (ow temperature control) 2000 10

Slope 2175 11

Displace (parallel displacement) 2176 13

Temp. min. (ow temp. limit, min.) 2177 13

Temp. max. (ow temp. limit, max.) 2178 13

Room T limit (room temperature limitation) 3000 14

Intgr. time (time constant for room temp.) 3015 16

Gain - max. (room temp. limitation, max.) 3182 16

Gain - min. (room temp. limitation, min.) 3183 16

Return T limit (return temp. limitation) 4000 17

Limit (return temp. limitation) 4030 17

Gain - max. (return temp. limitation - max. inuence) 4035 18

Gain - min. (return temp. limitation - min. inuence) 4036 18

Intgr. time (time constant for return temp. limitation) 4037 19

Priority (priority for return temp. limitation) 4085 19

Optimize 5000 20

Auto-reduct (setback temp. dependent on outdoor temp.) 5011 20

Boost 5012 20

Ramp (reference ramping) 5013 21

Optimizer (optimizing time constant) 5014 21

Based on (optimization based on room / outdoor temp.) 5020 22

Total stop 5021 23

S1 T lter (outdoor temp. lter) 5081 23

Cut-out (limit for heating cut-out) 5179 24

VI.KT.G6.02

4 | © Danfoss | 2016.05

Table of contents

Control param. (control parameters) 6000 25

Motor prot. (motor protection) 6174 25

Xp (proportional band) 6184 25

Tn (integration time constant) 6185 25

M1 run (running time of the motorized control valve) 6186 25

Nz (neutral zone) 6187 26

Application 7000 28

ECA address (choice of room panel / remote control) 7010 28

P1 exercise (pump exercise) 7022 28

M1 exercise (valve exercise) 7023 28

Actuator (gear motor / thermo actuator) 7024 28

DHW prior. (closed valve / normal operation) 7052 29

P1 frost T (frost protection) 7077 29

P1 heat T (heat demand) 7078 30

Standby T (standby temperature) 7093 30

Ext. (external override) 7141 30

Knee point 7162 31

Min. on time (min. activation time gear motor) 7189 31

Daylight (daylight saving time changeover) 7198 31

ECL address (master / slave address) 7199 31

Type 7600 32

Service 8000 33

Code no. 8300 33

Ver. (version no.) 8301 33

Backlight (display brightness) 8310 33

Contrast (display contrast) 8311 33

Language 8315 34

MOD address (MODBUS address) 8320 34

Installation 35

Mounting the ECL Comfort controller 35

Electrical connections - 230 V a.c. - in general 36

Electrical connections - 24 V a.c. - in general 37

Connecting the temperature sensors and the ECL BUS 38

How to identify your system type 39

Adapting the ECL Comfort 110 controller 41

Manual control 42

Placing the temperature sensors 43

Connecting the room panel / remote control 44

Checklist, electrical connections 45

Frequently asked questions 46

Denitions 47

VI.KT.G6.02 © Danfoss | 2016.05 | 5

Introduction

How to use this guide

The instructions is divided into six parts:

• Introduction

• Settings overview

• Daily use

• Maintenance

• Installation

• Check

Basic principles of application 130 for ECL Comfort 110

Typically, the ow temperature is always adjusted according to your requirements.

The ow temperature sensor (S3) is the most important sensor. The desired ow

temperature at S3 is calculated in the ECL Comfort controller, based on the outdoor

temperature (S1). The lower the outdoor temperature, the higher the desired ow

temperature.

The motorized control valve (M1) is opened gradually when the ow temperature is

lower than the desired ow temperature and vice versa.

The return temperature (S4) to the district heating supply should not be too high. If so,

the desired ow temperature can be adjusted (typically to a lower value) thus resulting

in a gradual closing of the motorized control valve. In boiler-based heating supply the

return temperature should not be too low (same adjustment procedure as above).

If the measured room temperature does not equal the desired room temperature, the

desired ow temperature can be adjusted.

The circulation pump, P1, is ON when the desired ow temperature is higher than 20 °C

(factory setting) or the outdoor temperature is lower than 2 °C (factory setting).

°C (degrees Celsius) is an absolute temperature whereas K (Kelvin) is a relative temperature.

VI.KT.G6.02

6 | © Danfoss | 2016.05

Settings overview

Line Page Factory

setting Your setting

Slope 2175 11

Displace (parallel displacement) 2176 13

Temp. min. (ow temp. limit, min.) 2177 13

Temp. max. (ow temp. limit, max.) 2178 13

Intgr. time (time constant for room temp.) 3015 16

Gain - max. (room temp. limitation, max.) 3182 16

Gain - min. (room temp. limitation, min.) 3183 16

Limit (return temp. limitation) 4030 17

Gain - max. (return temp. limitation - max. inuence) 4035 18

Gain - min. (return temp. limitation - min. inuence) 4036 18

Intgr. time (time constant for return temp. limitation) 4037 19

Priority (priority for return temp. limitation) 4085 19

Auto-reduct (setback temp. dependent on outdoor temp.) 5011 20

Boost 5012 20

Ramp (reference ramping) 5013 21

Optimizer (optimizing time constant) 5014 21

Based on (optimization based on room / outdoor temp.) 5020 22

Total stop 5021 23

S1 T lter (outdoor temp. lter) 5081 23

Cut-out (limit for heating cut-out) 5179 24

Motor prot. (motor protection) 6174 25

Xp (proportional band) 6184 25

Tn (integration time constant) 6185 25

M1 run (running time of the motorized control valve) 6186 25

Nz (neutral zone) 6187 26

ECA address (choice of room panel / remote control) 7010 28

P1 exercise (pump exercise) 7022 28

M1 exercise (valve exercise) 7023 28

Actuator (gear motor / thermo actuator) 7024 28

DHW prior. (closed valve / normal operation) 7052 29

P1 frost T (frost protection) 7077 29

P1 heat T (heat demand) 7078 30

Standby T (standby temperature) 7093 30

Ext. (external override) 7141 30

Knee point 7162 31

Min. on time (min. activation time gear motor) 7189 31

Daylight (daylight saving time changeover) 7198 31

ECL address (master / slave address) 7199 31

Type 7600 32

Code no. 8300 33

Ver. (version no.) 8301 33

Backlight (display brightness) 8310 33

Contrast (display contrast) 8311 33

Language 8315 34

MOD address (MODBUS address) 8320 34

1.2

10 °C

90 °C

OFF

-4.0

0.0

50 °C

-2.0

0.0

25 s

OFF

-15 °C

OFF

OUT

OFF

100

18 °C

OFF

80 K

30 s

35 s

3 K

OFF

GEAR

OFF

2 °C

20 °C

10 °C

OFF

40 °C

130

XXXX

English

VI.KT.G6.02 © Danfoss | 2016.05 | 7

Daily use

Temperatures

Push any button to switch on the backlight.

Mode COMFORT

Temp. 19 <

Setting the desired room temperature

Change the desired temperature.

The setting of the desired room temperature is important even if a room temperature sensor

/ room panel / remote control is not connected.

Is the room temperature too low?

Make sure that the radiator thermostat(s) does not limit the room temperature.

If you still cannot obtain the desired room temperature by adjusting the radiator

thermostats, the ow temperature is too low. Increase the desired room temperature.

Temperature overview

2 sec.

Push the button to see the sensor (S1-S4) temperatures.

Change between the temperature displays:

S1:

Actual outdoor temperature

Accumulated outdoor temperature

S1 acc. T 12@

S1 act. T 13@

S2:

Actual room temperature

Desired room temperature

S2 des. T 21@

S2 act. T 20@

S3:

Actual ow temperature

Desired ow temperature

S3 des. T 42@

S3 act. T 43@

S4:

Actual return temperature

Desired return temperature limitation

S4 lim. T 30@

S4 act. T 28@

VI.KT.G6.02

8 | © Danfoss | 2016.05

Daily use

Push to exit ‘Temperature overview’.

If the temperature value is displayed as

"- -" the sensor in question is not connected.

"- - -" the sensor is short-circuited.

Select control mode

During scheduled operation (AUTO), the symbols will show you the control mode.

Wednesday

Mode COMFORT<

Change the mode (AUTO, COMFORT, SETBACK, or STANDBY).

Set your personal schedule

It is only possible to set the personal schedules if the ECL Comfort 110 controller has a built-in

ECA 110 timer program.

04-01-12 8:32

Wednesday <

This display will show the current day and time.

Choose the day for which you wish to change the settings.

VI.KT.G6.02 © Danfoss | 2016.05 | 9

Daily use

Today’s schedule

The rst display will show you the start of the rst comfort period (‘Start1’). See or change

the start of this period.

The rst bar will blink.

Wed ]]]][!]]]!!]

Start1

09:00

See or change the end (‘Stop1’) of the rst comfort period.

The next bar will blink.

Wed ]]]][!{]]!!]

Stop1 12:00

See or change the start (‘Start2’) of the next comfort period.

Wed ]]]][!{]]!!]

Start2 18:00

See or change the next start / stop periods, if necessary.

Wed ]]]][!{]]!!]

Stop2 22:00

The schedule has always two comfort periods a day. The start and stop times can be set in

half-hourly intervals (30 min.).

To arrange only one comfort period on a day: Set Start2 and Stop2 times to the same time

value.

VI.KT.G6.02

10 | © Danfoss | 2016.05

Maintenance

2 sec.

Enter the maintenance menus.

Date - time 1000

It is only necessary to set the correct date and time in connection with the rst use of the

ECL Comfort 110 controller or after a power break of more than 36 hours (see the chapter

on Adapting the ECL Comfort 110 controller).

Flow temp. (ow temperature control) 2000

Heat curve

The ECL Comfort 110 controls the heating system according to the calculated ow

temperature under the inuence of the return and / or room temperature.

The desired ow temperature is dened by 5 settings: ‘Temp. max.’, ‘Temp. min.’, ‘Slope’,

‘Displace’, and ‘Knee point’.

Desired ow temperature

-20 -10 0 10 20-30

100

110

[°C]

Heat curve

‘Slope’

‘Temp. max.’

‘Displace’

‘Knee point’

‘Temp. min.’

Outdoor temp.

The calculated ow temperature can be inuenced by connected sensors, ‘Boost’ and ‘Ramp’

etc.

Andere Handbücher für ECL Comfort 110

Inhaltsverzeichnis

Andere Danfoss Controller Handbücher

Danfoss

Danfoss AMD 613 Bedienungsanleitung

Danfoss

Danfoss ERC 213 Bedienungsanleitung

Danfoss

Danfoss NovoCon S 003Z8504 Bedienungsanleitung

Danfoss

Danfoss AK-PC 520 Bedienungsanleitung

Danfoss

Danfoss vlt soft starter mcd 500 Bedienungsanleitung

Danfoss

Danfoss AME 130 Bedienungsanleitung

Danfoss

Danfoss AVT/VG Bedienungsanleitung

Danfoss

Danfoss OPTYMA Plus OP-LPQM Bedienungsanleitung

Danfoss

Danfoss AMV 410 Bedienungsanleitung

Danfoss

Danfoss PN 16 Bedienungsanleitung

Danfoss

Danfoss DMS 300 Bedienungsanleitung

Danfoss

Danfoss AVQM Series Bedienungsanleitung

Danfoss

Danfoss VLT 6000 series Bedienungsanleitung

Danfoss

Danfoss Vacon NXP Series Bedienungsanleitung

Danfoss

Danfoss EKD 316 Bedienungsanleitung

Danfoss

Danfoss VLT Soft Starter MCD 600 Bedienungsanleitung

Danfoss

Danfoss EKC 315A Bedienungsanleitung

Danfoss

Danfoss AMV213 Bedienungsanleitung

Danfoss

Danfoss VLT DMS 300 Bedienungsanleitung

Danfoss

Danfoss VACON 100 industrial Bedienungsanleitung

Danfoss

Danfoss MCO 351 Gebrauchsanweisung

Danfoss

Danfoss AFPQ 2 Bedienungsanleitung

Danfoss

Danfoss VLT HVAC Drive FC 102 Betriebsanleitung

Danfoss

Danfoss VLT AutomationDrive FC 302 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung