Danfoss KP 1 Bedienungsanleitung
INSTRUCTIONS
KP 1, KP 2,
KP 5, KP 7W, KP 7B
060R9746
RI.05.1A.22 ®RI.5A.J1.22 01-1999
Types
The controls can be used with CFC, HFC
and HCFC refrigerants.
CAUTION: Do not install these controls on
ammonia systems.
CAUTION: Do not mount the control in a position where dirt,
sediment, or oil will affect the operation of the control.
Mounting requirements Ambient temperatures
Auto reset: KP 1, KP 2, KP 5, KP 7W Manual reset: KP 1, KP 5, KP 7B
CAUTION: The mounting panel must be plane to avoid damage of control.
Enclosure
Test pressure (pTEST) Connections
060R9746
© Danfoss A/S
t1min. KP 1, 2, 5: –40°F (–40°C)
KP 7: –13°F (–25°C)
t1max. 150°F (65°C)
ptest max.:
KP 1, 2: 285 psig (20 bar pe)
KP 5, 7: 505 psig (35 bar pe)
Electrical contacts/wiring test
TRIP (main lever)
use FINGERS ONLY!
(Do NOT use screwdriver)
Note:
KP 1, KP 5 and KP 7B w/man. reset:
Push manual reset knob during manual
tripping.
Wiring
CAUTION: Disconnect power supply before
wiring connections are made to avoid
possible electrical shock or damage to
equipment.
All wiring should conform to the National
Electrical Code and local regulations.
Terminal block
CAUTION: Use terminal screws furnished
in the contact block.
Use tightening torque 20 lb. in (2.3 Nm).
Use copper wire only.
Contact load ratings
Load Option A
CUT-OUT on pressure drop
Wire terminals 1-4:
CUT-IN = High Set Point (HSP)
see “Setting”
CUT-OUT = Low Set Point (LSP)
see “Setting”
Terms 1-4 close on pressure rise
Terms 1-4 open on pressure drop
Example: CUT-IN = 30 psig
CUT-OUT = 10 psig
This means CUT-IN = HSP = 30 psig
CUT-OUT = LSP = 10 psig
Note:
= Bellows movement on pressure rise
Ø= Bellows movement on pressure drop
The free terminal can be used for signal
purpose.
Load Option B
CUT-OUT on pressure rise
Wire terminals 1-2:
CUT-IN = Low Set Point (LSP)
see “Setting”
CUT-OUT = High Set Point (HSP)
see “Setting”
Terms 1-2 close on pressure drop
Terms 1-2 open on pressure rise
Example: CUT-IN = 250 psig
CUT-OUT = 350 psig
This means CUT-IN = LSP = 250 psig
CUT-OUT = HSP = 350 psig
120 V a.c. 16 FLA, 96 LRA
240 V a.c. 8 FLA, 48 LRA
240 V d.c. 12 W pilot duty
Manual reset
To resume control operation after safety
cutout, push reset knob as indicated.
Note:
KP 1, man. reset is possible only after a
pressure rise of 10 psi (0.7 bar).
KP 5 and KP 7B, man. reset is possible only
after a pressure drop of respectively 43 psi
(3.0 bar) and 58 psi (4.0 bar)
RI.5A.J1.22 © Danfoss A/S
Bellows Bellows
Diff. (fixed)
KP 1: 10 psi (0.7 bar
KP 5: 43 psi (3 bar)
KP 7B: 58 psi (4 bar)
Adjustment spindle(s) location
Auto reset Manual reset
KP 1, 2, 5, 7W KP 1, 5, 7B
Setting
(se also “Wiring”)
KP 1 (auto reset), KP 2, KP 5, KP 7W and KP 7B KP 1 (manual reset ONLY)
1. Adjust range spindle to desired 1. Adjust range spindle to desired
HIGH SET POINT (HSP) LOW SET POINT (LSP)
2. Adjust differential spindle to 2. DIFFERENTIAL is fixed.
desired DIFFERENTIAL (DIFF.) Value printed on scale plate
Note:
KP 5 (manual reset) and KP 7B have fixed diff.
Value printed on scale plate.
HIGH SET POINT minus DIFFERENTIAL equals LOW SET POINT LOW SET POINT plus DIFFERENTIAL equals HIGH SET POINT
Example: Example:
HSP – DIFF. = LSP LSP + DIFF. = HSP
30 psig – 20 psi = 10 psig 12 psig + 10 psi = 22 psig
(2.1 bar) (1.4 bar) (0.7 bar) (0.8 bar) (0.7 bar) (1.5 bar)
If terminals 1-4 are used: CUT-IN = HSP
CUT-OUT = LSP
If terminals 1-2 are used: CUT-IN = LSP
CUT-OUT = HSP
RI.5A.J1.22 © Danfoss A/S
10 psi (0.7 bar) /
rev. KP 1
7 psi (0.5 bar) /
rev. KP 2
33 psi (2.3 bar) /
rev. KP 5, 7W, 7B 3 psi (0.2 bar) / rev. KP 1
1.5 psi (0.1 bar) / rev. KP 2
4 psi (0.3 bar) / rev. KP 5
7 psi (0.5 bar) / rev. KP 7W
Adjustment
See instruction printed on top of control
Note:
Remove lock plate before adjustment.
Replace lock plate after adjustment (if desired).
© Danfoss A/S (AC-SP,jp) 01-1999RI.5A.J1.22
Dieses Handbuch passt für folgende Modelle
4
Andere Danfoss Schalten Handbücher
Danfoss
Danfoss AMV 410 Bedienungsanleitung
Danfoss
Danfoss KPI 34 Bedienungsanleitung
Danfoss
Danfoss BCP1H Bedienungsanleitung
Danfoss
Danfoss KP 1 Bedienungsanleitung
Danfoss
Danfoss KP 15 Bedienungsanleitung
Danfoss
Danfoss RT 112 Bedienungsanleitung
Danfoss
Danfoss KP 44 Bedienungsanleitung
Danfoss
Danfoss KP 15 Bedienungsanleitung
Danfoss
Danfoss RT 1AL Bedienungsanleitung
Danfoss
Danfoss RT 1AE Bedienungsanleitung
Danfoss
Danfoss KPU 1 Bedienungsanleitung
Danfoss
Danfoss CWH1000 Handbuch
Danfoss
Danfoss MP 54 Bedienungsanleitung
Danfoss
Danfoss RT 30AW Bedienungsanleitung
Danfoss
Danfoss RT 260A Bedienungsanleitung
Danfoss
Danfoss KPU Series Bedienungsanleitung
Danfoss
Danfoss KPS 35 Bedienungsanleitung
Danfoss
Danfoss RT 6AEW Bedienungsanleitung
Danfoss
Danfoss KP 7ABS Bedienungsanleitung
Danfoss
Danfoss RT 260A Bedienungsanleitung
