Daniamant Dan W3-2 Bedienungsanleitung

W3-2 Instruction Issue 6 (D0685)

Description

The Dan W3-2 is a flashing lifejacket light which is activated by a water sensor or

manually using the on/off button.

The light is designed to be fitted by the lifejacket manufacturer only.

Daniamant A/S

Industrivej 24C

DK-3550, Slangerup, Denmark

Tel: +45 47 37 38 00 Fax: +45 47 37 38 09

Email: [email protected]

www.daniamant.com

Dan W3-2 lifejacket light

Installation and Maintenance Instructions

Installation

The Dan W3-2 is for use on all types of lifejackets.

The Dan W3-2 is supplied with a fixing clip. The clip is intended to be placed

behind a strip of lifejacket material or reflective tape; the light is secured by

pressing it into the clip.

Light and fixing clip (part no.1950 for grey standard clip, for 1” webbing + part no. 1952 Clips 2, for 2”

webbing) separated to show material path

It is the responsibility of the lifejacket manufacturer to ensure that the light is

attached securely and is in the correct position on the lifejacket to provide

maximum visibility when the wearer is in the water.

Operation

The DAN W3-2 is switched on automatically when the sensor is immersed in

water and can be switched off by pressing the on/off button.

The light can also be activated and deactivated manually by pressing the on/off

button.

The sensor on the cable can be tested by a metal clip.

Figure depicts the Sensor Switch and the Manual ON/OFF Button

ON/OFF

Button

Sensor

Switch

p/n. 1950

p/n. 1952

Maintenance

Routine service

Dan W3-2 is maintenance free, but the following checks must be made annually:

1. Inspect the light for signs of damage or corrosion.

2. Press the on/off button and the light will commence flashing, then press

the button once more and the light should deactivate.

3. To test the Sensor, Switch and the cable –a paper clip may be applied to

the 2 water contacts. It is recommended that the light is activated for 1

minute.

Replacement

The Dan W3-2 lifejacket lights have a storage life of 5 years and must be

replaced by the date shown on the label.

Health and safety information

Dan W3-2 lights contain Lithium cells. These must be handled correctly:

•Do not dismantle the light assembly

•Do not make any external electrical connection

•Do not recharge

•Do not incinerate

Store between -30°C and +65°C

The Batteries are hermetically sealed pressurised primary Lithium/Manganese

cells, and as supplied are electrically protected by a solid state device and are

environmentally protected by a moulded plastic housing. In this condition the units

pose no definable hazard to health.

Information on the composition and behaviour of these products is contained in

the Product Safety Data Sheet, available from our website

(www.daniamant.com) or on request.

Disposal

Dispose of used and expired lights in accordance with local regulations. This

could be done through an approved environmental disposal agent.

All Daniamant product disposal instructions are available within the user instruction leaflet provided with the

product, or alternatively, available for download on this website.

Daniamant’s Survivor Location Lights contain batteries as well as electrical and electronic components, and

must therefore be segregated from the domestic waste stream and recycled. Disposing of this product

correctly will help save valuable resources and prevent any potential negative effects on human health and

the environment, which could otherwise arise from inappropriate waste handling. Daniamant’s lights are

marked with the symbol below which conveys that this waste must be treated separately from household

waste.

To ensure compliance with the WEEE and Battery Regulations, the Survivor Location Lights placed on the

market in the UK or Denmark should be returned to Daniamant in the UK or Denmark, or deposited in your

nearest WEEE Designated Collection Facility, operated by your Local Authority.

Further copies of this installation and maintenance instructions are available to download from

our website www.daniamant.com

A copy of these instructions must be held with the ships/owners training manual.

Inhaltsverzeichnis

Andere Daniamant Schiffsbeleuchtung Handbücher

Daniamant

Daniamant W3-1 Bedienungsanleitung

Beliebte Schiffsbeleuchtung Handbücher anderer Marken

Francis Searchlights

Francis Searchlights FX560 Bedienungsanleitung

Attwood

Attwood 5095 Bedienungsanleitung

Glamox

Glamox aqua signal TX20 Series Bedienungsanleitung

Attwood

Attwood 3100 Bedienungsanleitung

Imtra

Imtra BCM California 60 Bedienungsanleitung

Sealite

Sealite SL60 Beilage

Hella marine

Hella marine NAVILED PRO 2NM Bedienungsanleitung

ACR Electronics

ACR Electronics 3940 Montageanleitung

ETI Solid State Lighting

ETI Solid State Lighting 504081020 Bedienungsanleitung

Sea gull lighting

Sea gull lighting Traverse Lyte Retrofit Kit Bedienungsanleitung

Attwood

Attwood 3830 Bedienungsanleitung

Sealite

Sealite SL-15 Beilage

Attwood

Attwood 911339 Bedienungsanleitung

Attwood

Attwood 91041 Bedienungsanleitung

Tranberg

Tranberg TEF 2438N Bedienungsanleitung

Weems & Plath

Weems & Plath 700 Bedienungsanleitung

Hella marine

Hella marine NaviLED 360 2LT 980 960-0 Series Bedienungsanleitung

Hella marine

Hella marine NaviLED 360 PRO 2LT 980 910 Series Bedienungsanleitung