Dantel 00030-10 Bedienungsanleitung
CAUTION
Install or remove modules from the shelf only when the power is off.
If you install a module in the shelf with the power on, the internal
circuitry may suffer damage and the product warranty will be void.
Remove and install circuit boards only in a static-safe environment
(use antistatic wrist straps, smocks, footwear, etc.).
Keep circuit boards in their antistatic bags when they are not in use.
Do not ship or store circuit boards near strong electrostatic, electromag-
netic, magnetic, or radioactive fields.
For more complete information on electrostatic discharge safety
precautions, refer to BellcoreTM Technical Reference #TR-NWT-000870.
Copyright 1998 by Dantel, Inc. • Dantel is a registered trademark of Dantel, Inc. • ISO 9001 Registered
Printed in the U.S.A.
INSTALLATION&OPERATION MANUAL
00030-0898<90-00114>
00030-10 AND -11
ORDER WIRE
SPEAKER/AMPLIFIER
PANEL
About this Practice:
This practice has been reissued to:
• Meet ISO 9001 requirements.
Issue date: August 1998
Reissued Practices: Updated and
new content can be identified by a
banner in the right margin.
UPDATED
Table of Contents
Ordering Information ........................................................................... 2
General Description.............................................................................. 2
Circuit Description ............................................................................... 2
Installation............................................................................................ 4
Technical Specifications ....................................................................... 6
Warranty ............................................................................................... 8
FUSE
FUSE
ALARM VOLUME
PAGE 2 00030-0898<90-00114>
NOTE: This section lists the different options available for this product. To order any of the avail-
able options, contact Dantel Inside Sales through our toll-free number, 1-800-432-6835.
OPTION NUMBER FEATURES
A13-00030-10 Order Wire Speaker/Amplifier Panel, Single
A13-00030-11 Order Wire Speaker/Amplifier Panel, Dual
ORDERING INFORMATION
GENERAL DESCRIPTION
D
antels 00030-10 and -11 Order Wire Speaker/Amplifier
Panels provide monitoring facilities for one or two order wire
channels. These panels are intended to complement the DTSS3A
Selective Signaling Order Wire Terminal, but may also be used for
general purpose applications.
The -10 option monitors a single channel while the -11 is a dual
assembly. Each panel occupies 3 1/2" (2 rack units) of space in a
19" or 23" wide rack. Reversable attach angle brackets permit easy
installation in either size rack.
Panels include, for each channel:
♦Speaker
♦Amplifier
♦Volume Control
♦Fuse
♦Fuse Alarm LED
Each input is transformer isolated and can be strapped for either
600 ohm or bridging impedance. For those applications where the
source inpedance is very low, a 600 ohm resistor can also be
strapped in.
This unit operates on -21 to -56 VDC input power.
CIRCUIT DESCRIPTION
Fig. 1 shows the functional schematic for the 00030-10 Order
Wire Speaker/Amplifier Panel.
00030-0898<90-00114> PAGE 3
FIG. 1 - FUNCTIONAL SCHEMATIC, 00030-10
CIRCUIT DESCRIPTION
1
2
2
1
3
-10dB
P1
A
600 WSOURCING
IN OUT
T1
B
600 W
TERM.
IN
OUT
H
G
8WSPEAKER
Nominal 1W
-BATT
-21 to -56 V
TB1
CHASSIS
GND
GND
F1
0.5 AMP
R3
INSTALLATION
I
nstallation consists of mounting the speaker panel in the rack,
setting the strap options (refer to Table A), connecting the
signal leads to the wire-wrap pins at P1 (refer to Table B), and
connecting the power leads to TB1 (refer to Table C).
Refer to Figs. 2 and 3 for a top view and front view of this unit.
Refer to Fig. 4 for terminal locations.
TABLE A - STRAP OPTIONS, 00030
OPTION
Bridging Input
600 ohm Terminated Input
600 ohm Sourcing for low impe-
dance source (used with DTSS3A).
STRAP SETTINGS
A OUT; B OUT
A OUT; B IN
A IN; B IN
PAGE 4 00030-0898<90-00114>
INPUT
Speaker (to P1-12 on DTSS3A)
Return (to P1-7 on DTSS3A)
PIN
P1-2
P1-1
POWER CONNECTION
-Battery
Ground
Chassis Ground
PIN
TB1-1
TB1-3
TB1-2
TABLE B-SIGNAL INPUT CONNECTIONS,00030
TABLE C - POWER CONNECTIONS, 00030
FIG. 2 - TOP VIEW, 00030
TOP VIEW
SPK - 1
3 2 1
GND BATT
T B 1
P1
2 1
17 1/4
19 or 23
Position of attach angles
for flush mounting
NOTE: Reverse attach angles
for 23 mounting
5
6
INSTALLATION
00030-0898<90-00114> PAGE 5
FIG. 3 - FRONT VIEW, 00030
INSTALLATION
FIG. 4 - REAR VIEW / TERMINAL LOCATIONS, 00030
FUSE
Mounting holes for wall phone
CONTROL LOCATIONS AND DIMENSIONS
FRONT VIEW
VOLUME
FUSE
ALARM
REAR VIEW SHOWING TERMINAL LOCATIONS
IN
OUT
OUT
IN
STRAP A
STRAP B
TB1
-BATT GND P1 12
R3 7
PAGE 6 00030-0898<90-00114>
TECHNICAL SPECIFICATIONS
DESCRIPTION
Input Voltage Range
Input Current
-10 Option
Idle
Max.
-11 Option
Idle
Max.
Heat Dissipation
-10 Option
Idle
Max.
-11 Option
Idle
Max.
Output Power
Maximum Input Level
Frequency Response
Input Impedance
Weight
Physical Dimensions
Mounting Projection
Operating Temperature Range
VALUE
-21 to -56 VDC
60 mA @ -56 VDC
250 mA @ -56 VDC
120 mA @ -56 VDC
500 mA @ -56 VDC
4.9 Btu/Hr @ -56 VDC
20.5 Btu/Hr @ -56 VDC
9.8 Btu/Hr @ -56 VDC
41 Btu/Hr @ -56 VDC
1 Watt
-10 dBm
300 Hz to 6 Khz + 1dB @ 1 watt
600 ohms or 10K ohm, selectable
2.5 lbs (-10 option); 3 lbs (-11 option)
17.75"W x 3.5"H x 6.0"D
5" or flush for 19" or 23" rack.
0° to 55° C.
00030-0898<90-00114> PAGE 7
NOTES
PAGE 8
8 PAGES 00030-0898<90-00114>
LIMITED WARRANTY
The Seller warrants that the standard hardware products sold will be free from defects in material and
workmanship and perform to the Sellers applicable published specifications for a period of 18 months for
hardware, and 3 months for software, from the date of the original invoice. The liability of the Seller hereunder
shall be limited to replacing or repairing, at its option, any defective products which are returned F.O.B. to the
Sellers plant, (or, at the Sellers option, refunding the purchase price of such products). In no case are products
to be returned without first obtaining permission and a customer return authorization number from the Seller.
In no event shall the Seller be liable for any consequential or incidental damages.
Equipment or parts which have been subject to abuse, misuse, accident, alteration, neglect, unauthorized
repair or installation are not covered by warranty. The Seller shall make the final determination as to the
existence and cause of any alleged defect. No warranty is made with respect to custom equipment or products
produced to the Buyers specifications except as specifically stated in writing by the Seller in the contract for
such custom equipment.
This warranty is the only warranty made by the Seller with respect to the goods delivered hereunder, and may
be modified or amended only by a written instrument signed by a duly authorized officer of the Seller and
accepted by the Buyer.
Warranty and remedies on products not manufactured by the Seller are in accordance with warranty of the
respective manufacturer. THE SELLER MAKES NO OTHER WARRANTY OF ANY KIND WHATSOEVER,
EXPRESSED OR IMPLIED; AND ALL IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PUR-
POSE WHICH EXCEEDS THE AFORESAID OBLIGATIONS IS HEREBY DISCLAIMED BY THE SELLER.
INCASE OF DIFFICULTY
If you experience difficulty with this equipment, check the following, as appropriate:
1. Switch settings
2. Signal levels
3. Software configuration
4. Connections between Dantel’s equipment and your equipment.
If there is still a problem, substitute equipment that is known to be good. For additional assistance, call
Dantels Technical Field Service Department weekdays, 6 A.M. to 5 P.M. pacific time:
1-800-4DANTEL (1-800-432-6835).
If a thorough checkout shows a piece of equipment has malfunctioned, you may return it to the factory. For
repairs and emergency replacements, obtain a Return Material Authorization (RMA) number from the Cus-
tomer Service Representative at 1-800-4DANTEL (1-800-432-6835).
To ensure expedient processing of your order, provide a purchase order number and shipping and billing
information when requesting an RMA number. Also, when the units are returned to Dantel, include a descrip-
tion of the failure symptoms for each unit returned. Send defective equipment to:
Dantel, Inc. • 2991 North Argyle Avenue • Fresno, California 93727-1388
P.O. Box 55013 • Fresno, CA 93747-5013 Phone (209) 292-1111 Fax (209) 292-9355 http://www.dantel.com
WARRANTY
Dieses Handbuch passt für folgende Modelle
3
Inhaltsverzeichnis
Andere Dantel Verstärker Handbücher
