Data I/O PSV5000 Bedienungsanleitung

Operator’s Manual

Automated Programming and Handling

096-0466-001E

Now available

with

LumenX Programmers

ii Data I/O • 096-0466-001E

096-0466-001 January 2019

Data I/O has endeavored to ensure that the information in this document is accurate and complete. Data I/O assumes no

liability for errors, or for any incidental, consequential, indirect, or special damages, including, without limitation, loss of

use, loss or alteration of data, delays, or lost profits or savings, arising from the use of this document or the applicable Data

I/O product.

Any algorithms, adapters or other Data I/O products provided or sold by Data I/O to you must first be tested and verified

by you for use in your application prior to use in a production environment. Data I/O does not warrant that the Data I/O

products will meet your requirements or that operation of the Data I/O products will be uninterrupted or error-free.

No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any

purpose, without written permission from Data I/O Corporation.

Data I/O, TaskLink, PSV5000, and Lumen[X] are trademarks of Data I/O Corporation.

Data I/O Corporation acknowledges the trademarks of other organizations for their respective products or services men-

tioned in this document.

We are interested in your comments. Please e-mail: [email protected]m

page i

Contents —Operator’s Manual

PSV5000 Machine Components 1

Work Surface Components 2

Power Panel Components 3

Programmer Overview 3

SAFETY MESSAGES AND PRECAUTIONS 7

Warnings and Cautions 7

Safety Systems 9

Emergency Stop (E-Stop) Buttons 9

Safety Doors and Interlocks 10

Electrostatic Discharge 10

RUNNING A JOB ON PSV5000 13

Requirements 13

List of Steps to Start a Job 13

1>> Checking the System 14

2>> Installing Input/Output Media 14

Setting Up Device Trays and Reject Bin 15

Installing the Tape-In Module Option 18

Installing the Tape Rewind Module 21

Checking the Tape Output Option 23

3>> Socket Adapters and Actuator Plates 31

Finding Socket Adapter Part Numbers 31

Installing Adapters and Actuators on FlashCORE 32

Adjusting the Actuator Plates 35

Installing Adapters and Actuators on LumenX 35

4>> Identifying the Correct Probes 38

Removing and Installing the Probe 40

Removing the Probe Holder 42

How to Teach a new TOOL Position 43

5>> Installing the Correct Laser Shuttle Tips 44

ii Data I/O • 096-0466-001E

6>> Running the Automatic Tray Feeder 45

Power Up the Tray Feeder 46

Verify Tray Feeder Initialization 46

Teaching the Tray 1 Location 48

7>> Turning PSV5000 System Power ON 51

8>> Selecting a Job—Starting CH700 51

To select and start a job for FlashCORE Programmers 52

To select and start a job for LumenX Programmers 54

9>> (Optional) Preselecting Programmers 56

10>> Setting Media and Options—the Setup Window 57

Verifying Media Setup 59

11>> Starting Programming 61

Laser Marking 61

Removing Devices 64

Stopping the System 64

Emergency Stop 65

Pausing a Job 66

Ending a Job 67

LIGHT TOWER INTERPRETATION 68

CHANGING PROGRAMMER STATUS 70

Disabling Programmers 70

MY JOBS THAT USE THE SAME SETUP 72

FINISHING A JOB 74

Turning PSV5000 System Power OFF 74

BASIC TRAY FEEDER OPERATION 76

IF YOU HAVE TROUBLE 77

INDEX 79

TECHNICAL SUPPORT

■ Work Surface Components ≡ Programmer Overview

PSV5000 Operator’s Manual - 1 -

PSV5000 Machine Components

This Visual Index of PSV5000 locates features and subassemblies on the machine.

Figure 1: Features of PSV5000; front (top) and back (bottom)

Gantry

Work surface

Optional:

Tape Output

Monitor and

Keyboard

Support for

Tape Feeder

Support for Option-

al Tray Feeder.

Light Tower

Interlocked

Safety Doors

Accessory

Drawer

Power Panel

E-Stop

Optional:

Laser Control

E-Stop

ESD ground

connection

PSV5000 Machine Components ■Work Surface Components

- 2 - Data I/O ■096-0466-001E

Work Surface Components

Figure 2: Some features on the PSV5000 work surface. The system can be

configured with a reject tray or a reject bin. Note that the static trays and

Tray Feeder would not both be used at the same time. (Refer to Owner’s

Manual or on-screen Help).

Tray alignment pins (3)

Tray Feeder

(optional)

Tape-In Module

[Tape Feeder] (optional)

Programmers

(only FC shown here)

Tray-capture

Magnet

Static Tray

Reject Bin

Tape-Out Module

(optional)

Vision

■ Power Panel Components ≡ Programmer Overview

PSV5000 Operator’s Manual - 3 -

Power Panel Components

Figure 3: Rear View of PSV5000. For information on connecting the facili-

ties, see the Owner’s Manual.

Programmer Overview

Two programmer models are available for the PSV5000: both models can be in-

stalled next to each other, but programming jobs can only be set to use one model.

Main Pressure Regulator

AC power connection

Main Power Switch;

Shown here in OFF position

(with lockout)

Air inlet valve

(with lockout

Internet connection

Programmer Power only

Socket Opener Pressure

Regulator

Main air inlet

Air Filter

PSV5000 Machine Components ■Power Panel Components

- 4 - Data I/O ■096-0466-001E

LumenX

Lumen™X is Data I/O’s latest programmer at the time of this document.

Each LumenX programmer requires one to two Actuator Plates and one to

eight Socket Adapters for the specific device package being programmed.

Each Socket Adapter has one socket.

Figure 4: One LumenX programmer with eight Sockets held down by four

clamps actuated by two adjustable Actuator Plates. Orange arrows indicate

Socket Adapters for the front half of the programmer.

LED Interpretation on LumenX Programmers

Figure 5: Each LumenX Socket Adapter has four LEDs and indicates

PIN 1 as shown. All four LEDs light at once only during startup and go off

when the startup procedure is complete.The Actuator Plate is not shown

here for clarity.

Green = PASS PROGRAMMING

Yellow = BUSY

Red = FAILED PROGRAMMING

White = CONTINUITY ERROR

Actuator Plate (2)

Clamp (4)

Spring Clip

(1 per clamp)

■ Power Panel Components ≡ Programmer Overview

PSV5000 Operator’s Manual - 5 -

FlashCORE III

Each FlashCORE III programmer requires an Actuator Plate and a Socket

Adapter for the specific device package being programmed. Each Socket

Adapter typically has four sockets.

Figure 6: FlashCORE III programmers on PSV5000.

LED Interpretation on FlashCORE Programmers

Figure 7: Each FlashCORE Socket Adapter has one red LED per socket. A)

Standard Adapter; socket 2 has failed. B) HIC Adapter. Socket 3 has failed.

The Actuator Plate is not shown on the HIC Adapter for clarity.

Supported Integrated Circuits (Devices)

• Flash Memory:

NOR, NAND, MCP, MMC, e.MMC, SD, MoviNAND, OneNAND, iNAND,

Serial Flash, EEPROM, EPROM

• Microcontrollers

• Logic devices:

CPLDs, FPGAs, PLDs

Actuator Plate

Socket Adapter

Programmer

PSV5000 Machine Components ■Power Panel Components

- 6 - Data I/O ■096-0466-001E

For administrative

functions and more, see

the PSV5000 Owner’s

Manual is in the

C:\CH700 directory on

the Handler computer

and also available on

our Technical Library on

our website).

Operator’s Manual

Operation

This manual includes basic operation of the PSV5000 System,

but not functions deemed Administrator functions such as

creating a job, teaching Package Files, or creating a data file

from a master device.

PSV5000 is a programming and handling system for traditional and fine-pitched

integrated circuits (devices). It accepts most package types. The on-screen applica-

tion that runs PSV5000 is CH700.

Operator functions include installing some hardware, checking hardware setup,

turning on power, starting TaskLink, loading a job, and running a job. Operators

generally follow this sequence to process devices:

Figure 1: Operator Functions. For a list of these steps, see page 13.

Safety

Precautions

page 7



Install media,

check options

page 14



Install Socket

Adapters,

page 32



Check probe

tips / shuttle

tips,

page 38



PSV5000

power up,

page 51



Start Task-

Link/LumenX,

load job,

page 52



Set UI media

and options,

page 57



Ensure

Package File

was taught



Start Pro-

gramming,

page 61

Finishing...



Finish or stop

a Job,

page 64 and



Resolving

Basic Errors,

page 68

Andere Handbücher für PSV5000

Inhaltsverzeichnis

Andere Data I/O Steuerungssystem Handbücher

Data I/O

Data I/O PSV7000 Bedienungsanleitung

Beliebte Steuerungssystem Handbücher anderer Marken

Pentair Pool Products

Pentair Pool Products Compool Bedienungsanleitung

ComfortNET

ComfortNET CTK04 Bedienungsanleitung

Fireye

Fireye InSight II 95DSS3 Bedienungsanleitung

CAME

CAME G3000 Bedienungsanleitung

Idemia

Idemia MorphoAccess VP MD Bedienungsanleitung

Axis

Axis P1445-LE-3 Bedienungsanleitung

HEIDENHAIN

HEIDENHAIN TNC 150 B Bedienungsanleitung

CNC-Step

CNC-Step High-Z T-Series Bedienungsanleitung

Doosan

Doosan DVF Series Bedienungsanleitung

Honeywell

Honeywell KAP 140 Bedienungsanleitung

Honeywell

Honeywell vk41 series Bedienungsanleitung

AirBench

AirBench FPW Installationsanleitung

Cypress

Cypress HHR-3160 Bedienungsanleitung

CAME

CAME GLT40AOS Bedienungsanleitung

Zonex

Zonex GEN II -VVT Benutzerhandbuch

Altronics

Altronics K 9650 Bedienungsanleitung

micro-trak

micro-trak RoadMaster Bedienungsanleitung

micro-trak

micro-trak Calc-An-Acre II Bedienungsanleitung