Data Video WM-11 Bedienungsanleitung

WM-11

Table of Contents

WARRANTY ................................................................................................... 3

STANDARD WARRANTY .......................................................................................3

THREE YEAR WARRANTY .....................................................................................4

DISPOSAL ......................................................................................................4

INTRODUCTION.............................................................................................5

PARTS ASSEMBLY AND INSTALLATION ..........................................................5

PRE-WORK ........................................................................................................5

PROCEDURE.......................................................................................................6

INSTALLING PTR-10/10T.............................................................................. 11

INSTALLING PTC-150 ................................................................................... 13

FREQUENTLY ASKED QUESTIONS................................................................. 15

DIMENSIONS AND WEIGHT ......................................................................... 16

SPECIFICATIONS .......................................................................................... 17

SERVICE AND SUPPORT ............................................................................... 20

Disclaimer of Product & Services

The information offered in this instruction manual is intended as a guide only.

At all times, Datavideo Technologies will try to give correct, complete and

suitable information. However, Datavideo Technologies cannot exclude that

some information in this manual, from time to time, may not be correct or

may be incomplete. This manual may contain typing errors, omissions or

incorrect information. Datavideo Technologies always recommend that you

double check the information in this document for accuracy before making

any purchase decision or using the product. Datavideo Technologies is not

responsible for any omissions or errors, or for any subsequent loss or damage

caused by using the information contained within this manual. Further advice

on the content of this manual or on the product can be obtained by

contacting your local Datavideo Office or dealer.

Warranty

Standard Warranty

Datavideo equipment is guaranteed against any manufacturing defects for

one year from the date of purchase.

The original purchase invoice or other documentary evidence should be

supplied at the time of any request for repair under warranty.

The product warranty period beings on the purchase date. If the purchase

date is unknown, the product warranty period begins on the thirtieth day

after shipment from a Datavideo office.

All non-Datavideo manufactured products (product without Datavideo

logo) have only one year warranty from the date of purchase.

Damage caused by accident, misuse, unauthorized repairs, sand, grit or

water is not covered under warranty.

Viruses and malware infections on the computer systems are not covered

under warranty.

Any errors that are caused by unauthorized third-party software

installations, which are not required by our computer systems, are not

covered under warranty.

All mail or transportation costs including insurance are at the expense of

the owner.

All other claims of any nature are not covered.

All accessories including headphones, cables, batteries, metal parts,

housing, cable reel and consumable parts are not covered under warranty.

Warranty only valid in the country or region of purchase.

Your statutory rights are not affected.

Three Year Warranty

All Datavideo products purchased after July 1st, 2017

qualify for a free two years extension to the standard

warranty, providing the product is registered with

Datavideo within 30 days of purchase.

Certain parts with limited lifetime expectancy such as LCD panels, DVD

drives, Hard Drive, Solid State Drive, SD Card, USB Thumb Drive, Lighting,

Non-PCIe Card and third party provided PC components are covered for 1

year.

The three-year warranty must be registered on Datavideo's official website

or with your local Datavideo office or one of its authorized distributors

within 30 days of purchase.

Disposal

For EU Customers only - WEEE Marking

This symbol on the product or on its packaging indicates that

this product must not be disposed of with your other

household waste. Instead, it is your responsibility to dispose of

your waste equipment by handing it over to a designated

collection point for the recycling of waste electrical and electronic equipment.

The separate collection and recycling of your waste equipment at the time of

disposal will help to conserve natural resources and ensure that it is recycled

in a manner that protects human health and the environment. For more

information about where you can drop off your waste equipment for recycling,

please contact your local city office, your household waste disposal service or

the shop where you purchased the product.

CE Marking is the symbol as shown on the left of this page.

The letters "CE" are the abbreviation of French phrase

"Conformité Européene" which literally means "European

Conformity". The term initially used was "EC Mark" and it was officially

replaced by "CE Marking" in the Directive 93/68/EEC in 1993. "CE Marking" is

now used in all EU official documents.

Introduction

WM-11 Professional Wall Mount is designed specifically for Datavideo

PTR-10/10T Robotic Pan Tilt Head as well as the PTZ camera series

(PTC-150/150T/200/200T). The two bubble level meters allow the user

to align the mounted device horizontally.

The four piece mounting kit is made of rugged metal and is easy to

install on any walls in either an upright or upside down position. The

assembled mount can support up to a 10 Kg load.

Note: WM-11 is designed for PTR series of robotic pan tilt heads and

PTC series of PTZ cameras.

Parts Assembly and Installation

In this section, you will be shown how you can assemble and install

your kit.

Pre-work

1. First check you have all the parts listed in the table below.

No.

Part Names

Qty

Wall plate

Left bracket

Right bracket

Round rod

Base plate

M5x20 nickel plated hex socket cap screw

Expansion bolt

Bubble level meter

M2.5 screw

M3 x 10mm screw and spring washer

M3 x 8mm screw

2. On the surface where the WM-11 is to be mounted, drill four holes

spaced according to the dimensions indicated in the diagram below.

Then follow the procedure in the next section to assemble and install

the WM-11.

Procedure

The diagram below is an exploded-view drawing of WM-11, and the

numbers correspond to the respective installation steps.

Bubble Level

Meter

1. First mount a bubble level meter to the wall plate using two M2.5

screws. Align the wall plate with the four holes drilled in Pre-Work

then use four expansion bolts to secure the wall plate. See the

diagram below.

Please note that you can use the bubble level meter to make sure

that the wall plate is properly aligned. If the bubble is at the center,

the wall plate is horizontally aligned (perfectly levelled). If the bubble

is on either side, the wall plate is tilted to the sides.

2. Assemble the left bracket to the wall plate with two M5x20 nickel

plated hex socket cap screws as shown in the diagram below.

3. Assemble the right bracket to the wall plate with two M5x20 nickel

plated hex socket cap screws as shown in the diagram below.

4. Place the round rod in between the left and right brackets then

secure it in position by fastening two M5x20 nickel plated hex

socket cap screws to the respective holes on the brackets as

shown in the diagram below.

5. Use four M2.5 screws to mount two bubble level meters to the

base plate with one in the front and one at the bottom.

Insert the base plate between the left and right brackets then

secure it in position by fastening six M5x20 nickel plated hex

socket cap screws to the respective holes on the brackets as

shown in the diagram below. By inspecting the bubble level meter,

you can make sure the base plate is properly aligned, i.e. the

bubble is at the center. The inner rails on the right and left

brackets should allow you to move the base plate back and forth.

Note: The base plate may be inserted in an upright or upside

down position.

Inhaltsverzeichnis

Andere Data Video Rack & Stand Handbücher

Data Video

Data Video WM-10 Bedienungsanleitung

Data Video

Data Video RKM-572 Bedienungsanleitung

Data Video

Data Video WM-1 Series Bedienungsanleitung

Data Video

Data Video PTR-10 Bedienungsanleitung

Data Video

Data Video LBK-2 Bedienungsanleitung

Data Video

Data Video RMK-2 Bedienungsanleitung

Data Video

Data Video RMK-1 Bedienungsanleitung

Data Video

Data Video RP-55 Bedienungsanleitung

Data Video

Data Video TTL-100 Bedienungsanleitung

Data Video

Data Video CM-10 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung