Data Video DAC-10 Technisches Datenblatt

Andere Handbücher für DAC-10

2

Inhaltsverzeichnis

Andere Data Video Schalten Handbücher

Data Video

Data Video SE-1000 Bedienungsanleitung

Data Video

Data Video SE-3000 Bedienungsanleitung

Data Video

Data Video SE-2200 Bedienungsanleitung

Data Video

Data Video SE-2000 Bedienungsanleitung

Data Video

Data Video HS-1500T Bedienungsanleitung

Data Video

Data Video SE-900 Bedienungsanleitung

Data Video

Data Video FS-30 Bedienungsanleitung

Data Video

Data Video SE-1000 Bedienungsanleitung

Data Video

Data Video HS-1600T Bedienungsanleitung

Data Video

Data Video SEB-1200 Bedienungsanleitung

Data Video

Data Video SE-600 Bedienungsanleitung

Data Video

Data Video SE-2000 Bedienungsanleitung

Data Video

Data Video KMU-200 Bedienungsanleitung

Data Video

Data Video SE-500 Bedienungsanleitung

Data Video

Data Video SE-500 Bedienungsanleitung

Data Video

Data Video SE-500HD Bedienungsanleitung

Data Video

Data Video SE-900 Bedienungsanleitung

Data Video

Data Video SE-2800 Bedienungsanleitung

Data Video

Data Video ITC-100 KF1000 Bedienungsanleitung

Data Video

Data Video SE-2800 Bedienungsanleitung

Data Video

Data Video SE-800 Bedienungsanleitung

Data Video

Data Video RP-54 Bedienungsanleitung

Data Video

Data Video SE-2000R Bedienungsanleitung

Data Video

Data Video SE-500MU4K Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

DAC-10 Quick Setup

This setup guide will cover four specific areas:

A. Explanation of the DAC-10 dip switches

B. Configuration of the dip switches

C. Cable connections for capturing

D. Cable connections for exporting

E. General Software Recommendations

A. Explanation of the DAC-10 Dip Switches

The DAC-10 has dip switches to customize the converter for your hardware and software.

The DAC-10 is sold throughout the world, so dip switch settings can be changed to

accommodate different regions and different firewire devices.

The diagram below explains what each dip switch controls within the DAC-10.

A. Configuration of the Dip Switches

Your DAC-10 dip switches have been preset for use with Windows XP and Macintosh

computers. Your dip switches should be set as follows:

C. Cable Connections for Capturing

Make sure your VCR or Analog sources output is connected to the inputs of the DAC-10.

A 6-pin FireWire cable can be connected to the rear of the DAC-10. The opposite end should

be connected to your FireWire connector on your computer.

If you would like to monitor your video, a composite BNC video cable can be used to connect

a video monitor. Connect a composite BNC cable from the rear output of the DAC-10 and

connect the opposite end to the input of your monitor.

Note: S-video cables only carry a video signal, so you will need to connect your RCA audio

cables to the converter to capture sound.

Helpful Hint: The “OUTPUT” from one device, must go to the “INPUT” on another device.

D. Cable Connections for Exporting

Make sure your VCR or Analog sources output is connected to the inputs of the DAC-10. We

also recommend connecting the composite output from the converter to a TV or Video Monitor

to verify the presence of a video signal.

E. General Software Recommendations

Connecting the DAC-10 to your Computer

Step 1 Power on your computer.

Step 2 Connect your Video and Audio cables.

Step 3 Connect your DAC-10 to your computer via FireWire. (IEEE/1394 Cable)

Step 4 Turn on your DAC-10 converter. In Windows, you should hear a tone and see a

confirmation that the converter has been detected. The dialog box will confirm that

an AVC Compliant Device was detected and it will ask you if you want to open a

specific application each time the device is attached.

Step 5 Launch Your Editing Application.

We recommend that you disable DV device control in your Editing Software. The DAC-10

converter will not support DV device control commands. In some cases, DV device control

will slow the editing application.

Make sure your Software is set to “mirror” what is on your timeline, with most software

applications this must be set or the result will be no DV output.

We also have a “Questions” area in the technical support link on our website, which will

answer Frequently Asked or Common Questions. Here is a direct link:

http://www.datavideo.us/support/faqs.htm