Datalogic BC-80X0 Cradle Bedienungsanleitung

BC-80X0 Cradle

Quick Reference Guide

Datalogic Scanning, Inc.

959 Terry Street

Eugene, Oregon 97402

USA

Telephone: (541) 683-5700

Fax: (541) 345-7140

procedures described therein may be reproduced or transmitted in any form or by any means with-

out prior written permission of Datalogic Scanning, Inc. or its subsidiaries or affiliates ("Datalogic"

or “Datalogic Scanning”). Owners of Datalogic products are hereby granted a non-exclusive, revo-

cable license to reproduce and transmit this documentation for the purchaser's own internal busi-

ness purposes. Purchaser shall not remove or alter any proprietary notices, including copyright

notices, contained in this documentation and shall ensure that all notices appear on any reproduc-

tions of the documentation.

Should future revisions of this manual be published, you can acquire printed versions by contact-

ing your Datalogic representative. Electronic versions may either be downloadable from the Data-

logic website (www.scanning.datalogic.com) or provided on appropriate media. If you visit our

website and would like to make comments or suggestions about this or other Datalogic publica-

tions, please let us know via the "Contact Datalogic" page.

Disclaimer

Datalogic has taken reasonable measures to provide information in this manual that is complete

and accurate, however, Datalogic reserves the right to change any specification at any time with-

out prior notice.

Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in many countries,

including the U.S.A and the E.U. All other brand and product names referred to herein may be

trademarks of their respective owners.

Patents

This product is covered by US Pat. 7,948,214 B2. Additional patents pending.

BC-80X0

USING THE BC-80X0 RADIO CRADLE

The BC-80X0 cradle, paired with one or more Powerscan™ M8300 readers,

builds a Cordless Reading System for the collection, decoding and transmission

of barcoded data.

It can be connected to a Host PC through an RS-232, USB, Wedge or Pen

cable and is suited for single-cradle point-to-point layouts. It can also be

connected to a C-BOX and therefore integrated into a fixed scanner application.

The BC-8060 models also allow multi-cradle layouts through an RS-485

Network. For this network connection refer to the Powerscan™ D8330/M8300

Reference Manual.

The label on the cradle contains LED indicators and a scan finder button.

When the button is pressed, the cradle transmits a “broadcast” message. All

properly configured scanners (Radio RX Timeout set to keep the radio “awake”)

that are linked to that base (through a bind or a join sequence) and within radio

range coverage will emit a beep sequence once every 2 seconds for 30

seconds. This functionality is useful to:

- verify which scanners are linked to a certain base station

- detect a scanner forgotten somewhere

The LEDs signal the BC-80X0 status, as described in the following table:

LED

STATUS

Aux

Yellow On = BC-80X0 is powered through an external power supply.

Yellow Blinking = BC-80X0 transmission occurs over the Host port.

Host

Yellow On = BC-80X0 is powered by the Host.

Yellow Blinking = BC-80X0 transmission occurs over the Host port.

Reader

Green On = the reader battery is completely charged.

Red On = the reader battery is charging.

Orange Blinking = reader battery fault – replace battery.

Red / Green Alternatively Blinking = charging error - see Ref. Manual

Spare*

Green On = the spare battery is completely charged.

Red On = the spare battery is charging.

Orange Blinking = spare battery fault – replace battery.

Red / Green Alternatively Blinking = charging error - see Ref. Manual

* This LED refers to the accessory SBS-8000 Spare Battery Slot when mounted to the BC-8060. Not

available for BC-8010 models.

Figure 1 – Cradle Overview

Figure 2 – LEDs

DATALOGIC

To set up your BC-80X0 cradle you must:

1. Physically install the cradle.

2. Make all system connections.

3. Configure the BC-80X0 cradle.

INSTALLATION

MOUNTING THE BC-80X0 CRADLE

The cradle package contains the following items:

BC-80X0

1 horizontal base

BC-80X0 Quick Reference Guide

2 wall-mounting lock hinges

BC-8000 Antenna

4 rubber feet

2 adhesive strips

1 inclined base

The cradle can be mounted for portable or fixed desktop usage, or it can be

fixed to a wall. The horizontal base allows portable and fixed desktop usage,

while the inclined base provides desktop and wall mounting guaranteeing a

comfortable handling of the Powerscan™ M8300 reader.

BC-80X0 Cradle mounted on the Horizontal Base

BC-80X0 Cradle mounted on the Inclined Base

BC-80X0

Desktop mounting

For desktop usage, you can mount the cradle either on the horizontal base, for

reduced overall dimensions, or on the inclined base for a more ergonomic taking

out and insertion of the reader onto the cradle.

Horizontal base

Top View Bottom View

Inclined base

Top View Bottom View

Mounting

Tabs (4)

Mounting

Holes (2)

Rubber Foot

Seat (4)

Adhesive

Strip Seat (2)

Cable

Channels

Mounting

Tabs (4)

Mounting

Holes (4)

Cable

Channels

Adhesive

Strip Seat (2)

Rubber

Foot Seat (4)

DATALOGIC

PORTABLE DESKTOP USE

1. Correctly position the BC-80X0 onto the base by sliding it along the

mounting tabs until aligned.

2. Carefully clean the rubber foot seats of the base to remove any impurities

that could reduce adhesion.

3. Remove the protective plastic from the rubber feet and stick them onto the

bottom surface of the base.

4. If mounting the BC-80X0 cradle, insert the antenna in the appropriate hole

on the body of the cradle and screw it clockwise until tight.

FIXED DESKTOP USE

For fixed desktop installation, use the adhesive strips or fixing screws (not

provided) according to your needs.

For mounting with adhesive strips:

1. Position the cradle onto the base by sliding it along the mounting tabs until

aligned.

2. Carefully clean the adhesive strip seats of the base to remove any

impurities that could reduce adhesion.

3. Remove the protective plastic from one side of the adhesive strips and

stick them onto the base surface.

4. Position the cables to be connected to the BC-80X0 cradle along the

dedicated channels, as shown in the figures below:

Horizontal Base

Inclined Base

BC-80X0

5. Remove the plastic from the other side of the strips and affix the base to

the table.

6. If mounting the BC-80X0 cradle, insert the antenna in the appropriate hole

on the body of the cradle and screw it clockwise until tight.

For mounting with screws:

1. Position the cables to be connected to the BC-80X0 cradle along the

dedicated channels, as shown in the figures below:

2. Position the base on the table and affix it by means of the screws (not

provided).

3. Position the cradle on the base by sliding it along the mounting tabs until

aligned.

4. If mounting the BC-80X0 cradle, insert the antenna in the appropriate hole

on the body of the cradle and screw it clockwise until tight.

Wall Mounting

1. Remove the yellow caps and insert the two wall mounting lock hinges

provided with your cradle.

DATALOGIC

2. Position the cables to be connected to the BC-80X0 cradle along the

dedicated channels (see figures at page 4).

If using the adhesive strips:

3. Carefully clean the adhesive strip

seats of the base to remove any

impurities that could reduce

adhesion.

4. Remove the protective plastic

from one side of the adhesive

strips and stick them onto the

base surface.

5. Remove the plastic from the

other side of the strips and affix

the base to the wall as indicated

in the figure below.

If using the mounting screws:

3. Using the mounting holes on the

base as a pattern, mark the wall

where you desire to mount the

BC-80X0.

4. Drill the appropriate size holes

and insert the threaded dowels

(not provided) into the holes.

5. Position the base on the wall as

indicated in the figure below and

affix it by means of the screws

(not provided).

Inclined Base Wall-mounting

6. Attach the cradle on the base by sliding it along the mounting tabs until

aligned.

7. If mounting the BC-80X0 cradle, insert the antenna in the appropriate hole

on the body of the cradle and screw it clockwise until tight.

BC-80X0

APPLYING RAPID POINT-TO-POINT CONFIGURATION

LABEL (OPTIONAL)

A pre-printed barcode label is included in the

package for rapid configuration of point-to-

point applications. If you wish to use this

method, apply this label to the seat provided

on the BC-80X0 cradle as shown in the

figure. See the Powerscan™ M8300 Quick

Reference Manual for the configuration

procedure.

SYSTEM CONNECTIONS

Connections should always be made with power off!

CAUTION

The BC-80X0 cradle provides two interface connectors and a power supply

connector as shown in the figure on the next page:

The RS-485 Network connection is available only on BC-8060 models. For

details about this type of connection, refer to the Powerscan™ D8330/M8300

Reference Manual.

To connect the BC-80X0 cradle to the Host through the multi-interface

connector, use the cable corresponding to the desired interface type.

Power Supply

RS-485

(BC-8060 only)

MULTI-INTERFACE

RS-232, USB, Wedge,

PEN Emulation

DATALOGIC

CONNECTING AND DISCONNECTING THE BC-80X0

INTERFACE CABLE

The BC-80X0 can be connected to a Host by means of an RS-232, USB, Wedge

or Pen cable, which must be simply plugged into the Host connector, visible on

the front panel of the cradle.

To disconnect the cable, insert a paper clip or other similar object into the hole

corresponding to the Host connector on the body of the cradle. Push down on the

clip while unplugging the cable. Refer to the following figure:

Connecting/Disconnecting the Cable

RS-232

USB

Power

Multi-standard interface

RS-232, USB, WEDGE, or

PEN Emulation to Host

Andere Handbücher für BC-80X0 Cradle

Inhaltsverzeichnis

Andere Datalogic Barcode-Lesegerät Handbücher

Datalogic

Datalogic DS8100A Bedienungsanleitung

Datalogic

Datalogic Touch 65 Pro Bedienungsanleitung

Datalogic

Datalogic QuickScan Lite QW2400 Bedienungsanleitung

Datalogic

Datalogic DSM0400 Bedienungsanleitung

Datalogic

Datalogic Magellan 8500Xt Bedienungsanleitung

Datalogic

Datalogic QuickScan QD2131 Bedienungsanleitung

Datalogic

Datalogic Matrix 120 Installations- und Betriebshandbuch

Datalogic

Datalogic Gryphon D412Plus Installations- und Betriebshandbuch

Datalogic

Datalogic QuickScan L Bedienungsanleitung

Datalogic

Datalogic PowerScan PD9531-AR Bedienungsanleitung

Datalogic

Datalogic Touch 90 pro Bedienungsanleitung

Datalogic

Datalogic Magellan 1500i Bedienungsanleitung

Datalogic

Datalogic Cobalto CO5330 Installations- und Betriebshandbuch

Datalogic

Datalogic Arex 420 Bedienungsanleitung

Datalogic

Datalogic PowerScan PD8530 Bedienungsanleitung

Datalogic

Datalogic Magellan 2200VS Bedienungsanleitung

Datalogic

Datalogic Gryphon I GD4132 Installations- und Betriebshandbuch

Datalogic

Datalogic Gryphon I GFE4500 Installations- und Betriebshandbuch

Datalogic

Datalogic F732-E Wizard Bedienungsanleitung

Datalogic

Datalogic QuickScan i Installations- und Betriebshandbuch

Datalogic

Datalogic DS1100 SH2347 Bedienungsanleitung

Datalogic

Datalogic OM-GRYPHON SERIES Bedienungsanleitung

Datalogic

Datalogic Gryphon I GM440 Series Installations- und Betriebshandbuch

Datalogic

Datalogic DX8200 Bedienungsanleitung

Beliebte Barcode-Lesegerät Handbücher anderer Marken

POSMicro

POSMicro Datalogic PowerScan D7100 Bedienungsanleitung

Marson

Marson MT780 Kurzanleitung zur Einrichtung

NCR

NCR RealPOS Bedienungsanleitung

Motorola

Motorola SE3300 Kurzanleitung zur Einrichtung

Element

Element P130BT Bedienungsanleitung

Motorola

Motorola Symbol LS3008 Installations- und Betriebshandbuch

Meec tools

Meec tools OBD-II / VAG Bedienungsanleitung

SICK

SICK CLP 100 Bedienungsanleitung

Royal Tag SA

Royal Tag SA I-Read Bedienungsanleitung

Welch Allyn

Welch Allyn IMAGETEAM 3800 Bedienungsanleitung

Meteor

Meteor 8310 Bedienungsanleitung

Denso

Denso BHT-500B Bedienungsanleitung

Motorola

Motorola MP6000 Montageanleitung

Newland

Newland NLS-HR15-BT Bedienungsanleitung

ARTDEV

ARTDEV AS-1310 Bedienungsanleitung

Aopos

Aopos AS290 Bedienungsanleitung

ENS

ENS 367-5455 Bedienungsanleitung

Atid

Atid AT188N Plus Bedienungsanleitung