Datalogic DL Cordless Card Bedienungsanleitung
DL
Reference Manual
Cordless Card™
DL Cordless Card™
REFERENCE MANUAL
DATALOGIC S.p.A.
Via Candini 2
40012 - Lippo di Calderara di Reno
Bologna - Italy
DL Cordless Card™
Ed.: 12/2003
This manual refers to software version 1.0 and later
ALL RIGHT RESERVED
Datalogic reserves the right to make modifications or improvements without prior modifications.
Datalogic shall not be liable for technical or editorial errors or omissions contained herein, nor for incidental or
consequential damages resulting from the use of this material.
Products names mentioned herein are for identification purposes only and may be trademarks and or
registered trademarks of their respective companies.
© Datalogic S.p.A. 2003
03/12/03
iii
CONTENTS
1INTRODUCTION ..........................................................................................1
1.1 Overview.......................................................................................................1
1.2 LED Indicator................................................................................................2
2INITIAL SETUP ............................................................................................3
2.1 Configuration Strings.....................................................................................3
2.2 DLCC Setup..................................................................................................4
3CONFIGURATION........................................................................................5
4PARAMETER ISSUES AND DEFINITIONS...............................................15
4.1 Radio and Serial Communication Controls .................................................15
4.2 COM Port Parameters.................................................................................20
4.2.1 Handshaking...............................................................................................20
4.2.2 ACK/NACK Protocol....................................................................................22
4.2.3 RX Timeout.................................................................................................23
4.2.4 FIFO............................................................................................................23
4.2.5 Frame Packing............................................................................................24
4.3 Data Format................................................................................................26
4.3.1 Header/Terminator Selection......................................................................26
4.3.2 Address Stamping.......................................................................................27
4.3.3 Address Delimiter........................................................................................28
4.4 Radio Parameters.......................................................................................29
4.4.1 RF Baud Rate.............................................................................................29
4.4.2 Transmission Mode (Client only).................................................................29
4.4.3 Radio Protocol Timeout (Client only)...........................................................29
4.4.4 Single Store (Client only)............................................................................29
4.4.5 ACK/NACK From Remote Host (Client only) ..............................................30
4.4.6 Beacon (Client only)....................................................................................31
5DEFAULT CONFIGURATION....................................................................32
6TECHNICAL FEATURES...........................................................................33
iv
REFERENCES
CONVENTIONS
This manual uses the following conventions:
"User" refers to anyone using a DL Cordless Card™.
"DLCC" refers to the DL Cordless Card™.
"You" refers to the System Administrator or Technical Support person using this
manual to install, configure, operate, maintain or troubleshoot a DLCC.
REFERENCE DOCUMENTATION
For further details refer to the card Quick Reference Manual and to the RHINO™
Reference Manual.
SERVICE, SUPPORT AND WARRANTY
Datalogic provides several services as well as technical support through its website.
Log on to www.datalogic.com/services/support and click on the links indicated for
further information including:
· Services - Warranty Extensions and Maintenance Agreements
· Support - Software Driver Downloads
· Contact Us - Listing of Datalogic Subsidiaries and Quality Partners
· Authorised Repair Centres
v
SAFETY PRECAUTIONS
Contact the competent authority responsible for the management of radio frequency
devices of your country to verify the eventual necessity of a user license.
Refer to the web site http://europa.eu.int/comm/enterprise/rtte/spectr.htm for further
information.
N2468
vi
QUICK START
The following can be used as a checklist to verify all of the steps necessary for
complete installation of the DL Cordless Card™ for a DOS terminal and for a laptop
(with two PCMCIA overlaid slots for PC cards of type II and with Windows 98, ME,
XP, and later versions).
Installing to portable PC
1) Read all information in the section "Safety Precautions" at the beginning of
this manual.
2) Start your PC.
3) Insert the DLCC correctly in the PCMCIA slot. Refer to the PC user's
manual.
Figure 1 - Laptop Card Installation
A) Windows notifies the PC has a new hardware device (DLCC);
B) Windows searches for a driver;
C) Insert the enclosed installation CD-ROM and follow the procedure;
D) At the end of the driver installation, Windows assigns DLCC a virtual
COM port.
4) Configure the DLCC address according to your application. See
"Configuration Methods".
NOTE
The default communication parameters of the COM port are: 9600
baud, no parity, 8 data bits, 1 stop bit, handshaking disabled
The installation is now complete.
vii
Installing to DOS Terminal
Read all information in the section "Safety Precautions" at the beginning of this
manual.
1) Rhino™ will recognize the card if the correct drivers are loaded. Therefore,
before inserting the card into the terminal make sure that:
- in NEWCFG.SYS the driver for the PCMCIA serial ports is loaded:
A:\PCMCIA\PCMSCD.EXE
- the scan engine driver is correctly configured (COM 3, interrupt 5) and
loaded after PCMSCD.EXE:
A:\DRIVERS\REDIR.SYS -c3 -i5 -b3
The following is an example of the NEWCFG.SYS:
;Load PCMCIA drivers
DEVICE=A:\PCMCIA\CNFIGNAM.EXE /DEFAULT
DEVICE=A:\PCMCIA\PCMSSC40.EXE
DEVICE=A:\PCMCIA\PCMCSFUL.EXE
DEVICE=A:\PCMCIA\PCMRMAN.SYS
DEVICEHIGH=A:\PCMCIA\PCMSCD.EXE
; Scan Engine Device Driver
; (Emulate SE1200 on Com3 @ 9600 N-8-1 Irq5)
DEVICEHIGH=A:\DRIVERS\REDIR.SYS -c3 -i5 -b3
2) Insert the DLCC correctly in the PCMCIA slot. Refer to the terminal user's
manual.
Figure 2 - DOS Terminal Card Installation
viii
3) Start the DOS terminal. The system assigns DLCC a virtual COM port
(COM 3, interrupt 5).
4) Configure the DLCC address according to your application. See
"Configuration Methods" paragraph.
NOTE
The default communication parameters of the COM port are: 9600
baud, no parity, 8 data bits, 1 stop bit, handshaking disabled
The installation is now complete.
Inhaltsverzeichnis
Andere Datalogic Barcode-Lesegerät Handbücher
Datalogic
Datalogic LYNX BT 432 Service-Handbuch
Datalogic
Datalogic DS6400 Bedienungsanleitung
Datalogic
Datalogic MAGELLAN 8400 Bedienungsanleitung
Datalogic
Datalogic QuickScan BC2030 Bedienungsanleitung
Datalogic
Datalogic PowerScan D8330 Bedienungsanleitung
Datalogic
Datalogic Matrix 300N Bedienungsanleitung
Datalogic
Datalogic MAGELLAN 3200VSI Bedienungsanleitung
Datalogic
Datalogic QuickScan Mobile Bedienungsanleitung
Datalogic
Datalogic Matrix 300 Bedienungsanleitung
Datalogic
Datalogic DS2x00N-DS4800 Series Leitfaden
Datalogic
Datalogic Compact 2D Reader Matrix-2000 Bedienungsanleitung
Datalogic
Datalogic Gryphon DX30 Bedienungsanleitung
Datalogic
Datalogic POWERSCAN SR Bedienungsanleitung
Datalogic
Datalogic QuickScan QD2430 Bedienungsanleitung
Datalogic
Datalogic PowerScan PD8590-DPM Bedienungsanleitung
Datalogic
Datalogic Cobalto CO5300 Bedienungsanleitung
Datalogic
Datalogic PowerScan PBT9501 Bedienungsanleitung
Datalogic
Datalogic QuickScan L QD 2300 Bedienungsanleitung
Datalogic
Datalogic lynx bt Bedienungsanleitung
Datalogic
Datalogic CBX500 Bedienungsanleitung
Beliebte Barcode-Lesegerät Handbücher anderer Marken
POSMicro
POSMicro Datalogic PowerScan D7100 Bedienungsanleitung
Marson
Marson MT780 Kurzanleitung zur Einrichtung
NCR
NCR RealPOS Bedienungsanleitung
Motorola
Motorola SE3300 Kurzanleitung zur Einrichtung
Element
Element P130BT Bedienungsanleitung
Motorola
Motorola Symbol LS3008 Installations- und Betriebshandbuch
