Datamax Allegro 2 Bedienungsanleitung
Allegro2
Operator’s Manual
HP PCB-4, and HP Laser Jet II are Trademarks of Hewlett Packard Corporation
CG Triumvirate is a trademark of Agfa Corporation.
CG Times, based upon Times New Roman under license from The Monotype
Corporation.
plc, is a product of Agfa Corporation.
Allegro2, SEAQ, and PC Batch are trademarks of Datamax Barcode Products
Corporation.
As an Energy Star Partner, Datamax Corporation has determined that this product
meets the Energy Star guidelines for energy efficiency.
Firmware (Software) Agreement:The enclosed Firmware (Software) resident
in the EPROM’s is owned by Licensor or its suppliers and is licensed for used
only on a single printer in the user’s Trade or Business. The User agrees not to,
and not to authorize or permit any other person or party to, duplicate or
copy the EPROM’s or the information contained in the EPROM’s. The
firmware (Software) is protected by applicable copyright laws and Licensor
retains all rights not expressly granted. In no event will Licensor or its suppliers
be liable for any damages or loss, including direct, incidental, economic, special,
or consequential damages, arising out of the use or inability to use the Firmware
(Software).
Information in this document is subject to change without notice and does not
represent a commitment on the part of Datamax Barcode Products Corporation.
No part of this manual may be reproduced or transmitted in any form or by any
means, for any purpose other than the purchaser's personal use, without the
expressed written permission of Datamax Corporation.
© Copyright 1997 by Datamax Corporation
7500 Flying Cloud Drive • Suite 655 • Eden Prairie, Minnesota 55344 •
(612) 946-0026
All rights reserved. Printed in the United States of America.
Part Number: 88-2183-01
Revision: A3
Agency Compliance and Approvals:
UL: UL1950 Information Technology Equipment
CSA: C22.2 No. 950-M93
TUV: EN60950, IEC950
VDE: Class B Vfg. 243/1991
1.Nur für Gebrauch innerhalb eines Gebäudes geeignet.
2.Bei Gefahr, Kabel aus der Steckdose herausziehen
3.Falls kein Kabel mitgeliefert wurde, bitte Folgendes bei der Anschaffung eines
Kabels beachten:
Für 230 Volt (Europa):Benützen Sie ein Kabel, das mit "HAR" markiert ist,
bestehend mindestens aus einem H05VV-F Kabel, das mindestens 0,75
Quadratmillimeter Drahtdurchmesser hat; sowie eine IEC320 Steckdose und
einen für das Land geeigneten Stecker, 6A, 250 Volt.
1.This unit is intended for indoor use only.
2.Disconnect power supply cord in case of emergency.
3.When power supply cord is not provided; for proper power supply cord
selection please see below:
For 230 Volt Operation (Europe):Use a cord set, marked "HAR," consisting of
a min H05VV-F cord which has a minimum 0.75 square mm diameter
conductors, provided with an IEC 320 receptacle and a male plug for the country
of installation rated 6A, 250V
FCC: This device complies with Part 15 of FCC rules.
Note: This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy, and if
not installed and used in accordance with the instructions in this manual, it
may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own
expense.
Important Safety Instructions
Your Barcode Printer has been designed to give you many years of
safe, reliable service. As with all electrical equipment, there are a few
basic precautions you should take to avoid getting hurt or damaging
the Printer.
•Carefully read the installation and operating instructions
provided with your Printer.
•Read and follow all warning instruction labels on the Printer
itself.
•Place the Printer on a flat, firm, solid surface.
•To protect your Printer from overheating, make sure all
openings on the Printer are not blocked.
•Do not place the Printer on or near a heat source, (i.e., a radiator
or heat register).
•Do not use your Printer near water, or spill liquid of any kind
into it.
•Be certain that your power source matches the rating listed on
the back of the Printer. If you are unsure, check with your
dealer or with your local power company.
•Do not place the power cord where it will be walked on. If the
power cord becomes damaged or frayed replace it immediately.
•Do not insert anything into the ventilation slots or openings on
the Printer.
•Only qualified, trained service technicians should attempt to
repair your Printer.
i
♦Contents
♦Getting Started
1.0 Introduction .....................................................1
1.1 Unpacking and Inspection ................................1
1.2 Tear-off Assembly Installation.......................... 4
1.3 Using the Printer Control Panel.........................5
1.4 Media Installation.............................................8
1.4.1 Label Loading Instructions..................9
1.4.2 Ribbon Loading Instructions ..............10
1.5 Using the Printer Options...................................11
1.6.1 Available Modules ..............................11
1.6.2 Options ...............................................12
♦Setting up the Printer
2.0 Checking Voltage Selection..............................15
2.1 Power Up Self-Test ..........................................15
2.2 Interfacing to the Printer...................................17
2.3 Sample Installations..........................................18
2.4 Switch Settings.................................................20
2.5 Programming Commands.................................23
2.6 Programming Examples....................................28
♦Creating Labels Using Internal Batch Software
3.0 Introduction .....................................................31
3.1 The Printer used with a LINK CRT...................32
3.2 Formatting and Printing Labels.........................35
3.3 Create/Modify Label Screen .............................40
3.4 Print Label Screen ...........................................53
3.5 System Maintenance Screen .............................55
3.6 Quick Reference Listing ..................................57
(Continued)
ii
♦Troubleshooting
4.0 Introduction .....................................................59
4.1 Controlling print quality ...................................60
4.2 Aligning the Printhead......................................61
4.2.1 Printhead Alignment Procedure .........63
4.2.2 Adjusting Printhead Pressure/Support 65
4.3 Troubleshooting.................................................66
♦Maintenance
5.0 Introduction .....................................................69
5.1 Cleaning Schedule............................................70
5.2 Cleaning the Printhead......................................70
♦Appendix A
ASCII Control Code Chart.................................A-1
♦Appendix B
Switch Settings and Cable Interfacing................B-1
♦Appendix C
Available Fonts and Barcodes............................C-1
♦Appendix D
Error Codes .......................................................D-1
♦Appendix E
Cable Listings ....................................................E-1
♦Appendix F
Specifications.....................................................F-1
♦Appendix G
Warranty Information........................................G-1
Allegro2 1
♦Getting Started
1.0 Introduction
The Allegro2Label Printer, hereafter referred to as the "Printer",
incorporates high-performance/low cost direct thermal and optional
thermal transfer label printing capabilities. The combination of
powerful capabilities, easy-to-use features, a contemporary look and
affordable pricing set a new standard for direct-thermal and
thermal-transfer label printers in retail, office and industrial
applications.
1.1 Unpacking and Inspection
Inspect the shipping container(s), if damage is evident, contact the
carrier to specify the nature and extent of the damage.
Remove the contents from the box. The Printer is enclosed in a
plastic bag to reduce the chance of moisture damage during
shipment, remove the plastic bag before use.
Along with this manual, the shipping container(s) should include the
following items:
•Label Printer
•Front Tear Bar Assembly
•Special or additional items purchased.
Getting Started
2Allegro2
Location of Parts on Your Printer
The following illustrations show the major components of your
Printer. Figure 1-2 is a detailed view of the print mechanism from
the side. Figure 1-3 is a back view of the Printer. Figure 1-5 is a
view of Printer’s switches and indicators.
In this manual we will refer to the components and connectors
depicted in these illustrations. If you are not installing the optional
Cutter or Front Rewind, then you should proceed to install the Front
Tear Bar Assembly at this time (see Figure 1.4).
Figure 1-2 Mechanism Detail
Inhaltsverzeichnis
Andere Datamax Etikettendrucker Handbücher
Datamax
Datamax A-Class A-4212 Bedienungsanleitung
Datamax
Datamax I-Class Mark II I-4212E/203 Bedienungsanleitung
Datamax
Datamax M-Class Mark II Bedienungsanleitung
Datamax
Datamax MICROFLASH 4T Bedienungsanleitung
Datamax
Datamax M-Class Mark II Bedienungsanleitung
Datamax
Datamax M-Class Mark II Bedienungsanleitung
Datamax
Datamax RL4e Bedienungsanleitung
Datamax
Datamax I-Class Bedienungsanleitung
Datamax
Datamax E-4304 Bedienungsanleitung
Datamax
Datamax H-Class Bedienungsanleitung
Datamax
Datamax Perfomance Series Bedienungsanleitung
Datamax
Datamax M-Class Mark II Bedienungsanleitung
Datamax
Datamax LP3 Bedienungsanleitung
Datamax
Datamax E-Class Mark III Professional+ Bedienungsanleitung
Datamax
Datamax I-Class Bedienungsanleitung
Datamax
Datamax I-class series Bedienungsanleitung
Datamax
Datamax A-Class Mark II Bedienungsanleitung
Datamax
Datamax Workstation w1110 Bedienungsanleitung
Datamax
Datamax M-Class Mark II Bedienungsanleitung
Datamax
Datamax Prodigy Plus Bedienungsanleitung
