SDS5-5 SERIES
INSTRUCTION MANUAL
CONTROLS
OUTPUT LED
The yellow LED indicates the output status.
STABILITY LED
The green LED ON indicates that the received signal has a reserve
greater than 30% compared to the output switching value.
TRIMMER
The 4-turn trimmer can be used to adjust the operating distance; the
distance increases turning the trimmer clockwise.
CONNECTIONS
+
BROWN
BLACK
WHITE
2
4
10 … 30 Vdc
BLUE 3
NC
NO
0 V
100 mA
100 mA
M12 CONNECTOR
2
3
1
4
DIMENSIONS
53.5
93.6
OUTPUT LED
TRIMMER
75.9
STABILITY LED
16.5
AXIAL VERSION
M18x1
AXIAL VERSION
16.5
75.9
53.5
M18x1
TRIMMER OUTPUT LED
22
65.1
M18x1
41.7
96.4
TRIMMER
OUTPUT LED
STABILITY LED
RADIAL VERSION
10.8
mm
10.8
RADIAL VERSION
22
65.1
41.7
M18x1
TRIMMER
CABLE VERSIONS M12 CONNECTOR VERSIONS
21.421.4
OUTPUT LED
8.8 9.2
9.2
8.8
M12
M12 M12
STABILITY LED
84.7 18.8
STABILITY LED
18.887.1
TECHNICAL DATA
Power supply: 10 … 30 Vdc; reverse polarity protection
Ripple: 2 Vpp max.
Current consumption
(output current excluded): 30 mA max.
Output: NC and NO, NPN or PNP; 30 Vdc max. (short-circuit protection)
Output current: 100 mA max.
Output saturation voltage: 1 V max NPN versions / 2 V max PNP versions
Response time: 2.5 ms max.
Switching frequency: 200 Hz max.
Indicators: OUTPUT LED (YELLOW) / STABILITY LED (GREEN)
Setting: operating distance 4-turn trimmer wiper idles
Operating temperature: -25 … 55 °C
Storage temperature: -25 … 70 °C
Electric shock protection: Class 2
Cutoff distance adjustment range: 50 … 100 mm
Operating distance: from 20 … 50 mm to 0 … 100 mm depending from cutoff adjustment
Emission type: RED (660 nm)
Ambient light rejection: according to EN 60947-5-2
Vibration: 0.5 mm amplitude, 10 … 55 Hz frequency, for every axis (EN60068-2-6)
Shock resistance: 11 ms (approx. 30 G) 6 shock for every axis (EN60068-2-27)
LIGHT/DARK selection: LIGHT mode on NO output
Housing: ABS UL 94V-O
Optics head: PVC
Lenses: Glass
Protection class: IP67 (TYPE 1 ENCLOSURE)
Connections: 2 m cable ∅5 mm / M12 4-pole connector
Weight: 100 g. max. cable versions / 30 g. max. connector versions
SETTING
Position the sensor and turn the operating distance trimmer to
maximum.
Place the target opposite the sensor at a slightly greater distance than
desired.
Turn the trimmer counterclockwise until the sensor switches.
Verify the adjustment moving the target closer and further the sensor;
tune the adjustment if necessary.
It is recommended to operate with the stability LED turned ON.
The white/grey remission diagram is shown below:
Grey test card (18% reflectance) cutoff point variation relative to white test
card (90% reflectance).
DECLARATION OF CONFORMITY
We DATASENSOR S.p.A. declare under our sole responsibility that
these products are conform to the 89/336 CEE, 73/23 CEE Directives
and successive amendments.
WARRANTY
DATASENSOR S.p.A. warrants its products to be free from defects.
DATASENSOR S.p.A. will repair or replace, free of charge, any product
found to be defective during the warranty period of 36 months from the
manufacturing date.
This warranty does not cover damage or liability deriving from the
improper application of DATASENSOR products.
DATASENSOR S.p.A. Via Lavino 265
40050 Monte S. Pietro - Bologna - Italy
Tel: +39 051 6765611 Fax: +39 051 6759324
DATASENSOR S.p.A. cares for the environment: 100% recycled
paper.
DATASENSOR S.p.A. reserves the right to make modifications
and improvements without prior notification.
826000263 Rev.C
0%
2%
4%
6%
8%
10%
12%
0 20406080100120
DISTANCE (mm)
PERCENT DEVIATION
STRAIGHT
VERSION
90° VERSION
