Davey ProMaster VSD ECO Series Bedienungsanleitung

Installation and Operating

Instructions

Model: PM200SV

WARNING: Failure to follow these instructions and comply with all applicable

codes may cause serious bodily injury and/or property damage.

The installation of this product should be carried out by a person knowledgable

in swimming pool plumbing requirements following the installation instructions

provided in this manual.

Please pass these instructions on to the operator of this equipment.

oMaster

™

VSD ECO-SERIES

Congratulations on the purchase of a quality product from the Davey Water

Products range of Pool and Spa Equipment. You are assured of many years

of reliable and super-efficient performance from your Davey ProMasterTM

VSD Eco-Series pump.

Read these instructions in their entirety before switching on this pump. If

you are uncertain as to any of these installation and operating instructions

please contact your Davey dealer or the appropriate Davey office as listed

on the back of this document.

The Davey ProMasterTM has been designed to circulate swimming pool and

spa water in conditions set out in the Australian Standard for swimming pool

water quality AS 3633 or equivalent. They should not be used for any other

purpose without first consulting your Davey Dealer or the Davey Customer

Service Centre.

Every Davey ProMasterTM is thoroughly water tested against a number of

flow, pressure, voltage, current and mechanical performance parameters.

Davey`s advanced pump manufacturing technology provides reliable and

efficient pumping performance that lasts and lasts.

Saving Energy with your Davey ProMasterTM

VSD Eco-Series Pump:

The Davey ProMasterTM Pool & Spa pump is a super efficient pump utilising

a very clever, state of the art infinitaly variable AC motor that provides lower

levels of noise, lower operating costs and lower greenhouse emissions than

traditional pool pumps.

Due to its ability to run at lower speeds than conventional pumps, your

ProMasterTM pump will also experience less mechanical wear and tear due

to less stress on the internal mechanical components.

To achieve energy efficient pumping is easy. Simply run the filtration

pump at a lower speed, but run it for longer (see table on page 8) than

a conventional fixed speed pump to “turn over” your pool water for

adequate filtration and sanitisation. The result is lower energy use and up

to 70% lower operational costs.

The ProMasterTM VSD Eco-Series has infinite speed settings from 1500

to 3600RPM, so you can circulate your pool or spa water at any speed

in between if required. Speeds can be adjusted to power a Suction pool

cleaner, In-Floor cleaning system & Pool Heaters. A Backwash setting on

the pump can be selected to backwash a media filter.

What to expect with VSD Eco speed pumping (energy efficient operation)

on your pool:

If your ProMasterTM pump is replacing a traditional AC motor pump, you will

need to run it longer than your old fixed speed pump. This is NORMAL and

you will save energy when using lower speed settings.

You may also notice that the pressure gauge on your filter is indicating

a much lower pressure than you are used to. This is also NORMAL. The

lower system pressure is simply a result of the lower speed and flow rate

produced by the pump.

While running at the lower speed settings you will also notice a significant

reduction in pump noise. This is a major benefit for you as it allows you to

run your pump during off peak electricity tariffs, which will also assist in the

reduction of your operating costs. Plus you will also have much happier

neighbours.

Important Considerations when running the pump on Low Flow settings:

Many pool products rely on particular minimum flow rates for best operation

and/or efficiency. If you are using the low flow setting on the ProMaster pump

(e.g.: speed 1 to 4) Davey recommends that you check the compatibility of

the speed or minimum flow rate required to run pool equipment such as:

• Suction pool cleaners

• Ozone generators

• Pool Heaters

• Solar Heating systems

• Salt Water Chlorinator cells

• In-floor pool cleaning systems

Technical Specifications:

Model PM200SV

Head (m) 22

RPM Speed 0 to 10 From – 1500 to 3600

Backwash Speed – 3800

Enclosure Class (IP) 45

Insulation Class F

Voltage (V) 220/240 AC

Supply Frequency (Hz) 50/60

Motor Input Power (W / hp)

Speed Setting 1 - 116W / 0.16 hp

Speed Setting 5 - 488W / 0.65 hp

Speed Setting 10 – 1000W / 1.34 hp

Backwash Setting – 1316W / 1.76 hp

Operating Limits:

Max Water temperature 40°C

Max Ambient temperature 50°C

Dimensions:

DIMENSIONS (mm)

Model A

B C

D E F G H I

Mounting

Holes

Diameter

Inlet/

Outlet

PVC

Net Weight

(kg)

PM200SV 305 670 320 350 65 230 380 200 250 10 40/50 14

Installation of the ProMasterTM VSD Eco-Series Pump:

Location

The pump should be located as close to the water as practicable and mounted

on a firm base in a well drained position, high enough to prevent any flooding. It is

the installer’s/owner’s responsibility to locate the pump such that the nameplate

can be easily read and the pump can be readily accessed for service.

Weather Protection

It is recommended that the pump is protected from the weather. Enclosures

should be ventilated to prevent condensation build-up.

Power Connection

Davey ProMasterTM is suitable for connection to a nominal 220/240 volt 50/60Hz

power supply and are equipped with a flex and 3 pin plug. If a power outlet is not

available within 3 metres of the pump, a 3 pin power point in a safe, dry place

may need to be provided by an electrician. Extension cords are unsafe around

pools - and should be avoided. If the supply cord of this product is damaged it

must be replaced by the dealer or manufacturer, with genuine Davey spares.

This ProMasterTM pool pump incorporates motor overload detection designed to

protect the motor from overheating. If the motor gets too hot during operation, it’s

operating speed will reduce to bring it within a acceptable operating temperature

and then will speed up to the originally set speed.

To reset the motor, switch the power off for 30 seconds, and then return the

power from the mains switch.

Davey Water Products recommends that all installations are tted with

earth leakage or residual current protection devices.

CAUTION: In the interest of safety, we advise that all brands and types

of pool pumps must be installed in accordance with AS3000 wiring rules

or equivalent.

If the pump and lter are located below pool water level, it is necessary to

t isolating valves in the pipe between the pump and skimmer box and in

return pipe from the lter to the pool.

The ttings on this product are constructed of ABS. Some PVC jointing

compounds are incompatible with ABS. Check compound suitability

before use.

Warning! Ensure that an electrical isolation switch is located with easy

access so that the pump can be switched off in an emergency.

Pipe Connection

Barrel unions are provided for connecting to the piping from the pool. The

pumps are designed to accept 40mm/50mm PVC fittings.

When plumbing the discharge pipe, ensure that the pipework does not

interfere with the pumps speed dial.

The use of any pipe smaller than those specified above is not recommended.

Suction piping should be free from all air leaks and any humps and hollows

which cause suction difficulties.

The discharge piping from the pump outlet should be connected to the inlet

connection on the swimming pool filter (usually at the filter control valve).

Barrel unions need to be hand tightened. No sealant, glues or silicones

are required.

Prior to using this pump you must ensure that: Checklist

• Speed Setting chosen is a compatible setting with other pool equipment 

• The pump is installed in a safe and dry environment 

• The pump enclosure has adequate drainage in the event of leakage 

• Any transport plugs are removed 

• The pipe-work is correctly sealed and supported 

• The pump is primed correctly 

• The power supply is correctly connected 

• All steps have been taken for safe operation 

• The filter has been plumbed with 40/50mm pipe 

Low Energy Operation:

Your ProMasterTM VSD Eco-Series pump has speed settings from

1500 to 3600 RPM:

- 1500 – Lowest Speed, 1

- 3600 – Highest Speed, 10

- 3800 – Backwash Speed

• Speed 1 provides the lowest speed and therefore the greatest energy

efficiency and savings. See page 9 for all other dial position speeds.

Operation Recommended Speed Setting

Pool Filtration Speed 1 to 4

Suction pool cleaner operation Speed 5 to 8

Backwashing your media filter Backwash Speed

Manually cleaning your pool

Speed 9 to 10

Water Feature operation

Spa Jet operation

Solar pool heating

Guidelines for Recommended Pump Operating Hours:

Australian Standards AS3633: “Private swimming pools - water quality”

states that “The minimum turnover rate shall be a single turnover of the full

volume of the pool water, within the period that the pump would normally be

operating….”

The table below provides a guide only to the running times of your pump

while in filtration mode in order to achieve the minimum turn over rate:

Pool Size

(Litres)

Speed Setting (hours)

Speed 1 Speed 5 Speed 10

20,000 3.3 1.7 1.1

30,000 5.0 2.5 1.7

40,000 6.7 3.3 2.2

50,000 8.3 4.2 2.8

60,000 10.0 5.0 3.3

80,000 13.3 6.7 4.4

100,000 16.7 8.3 5.6

NOTE: Whenever you increase the pump run time, you should decrease

the chlorine output of your chlorinator to avoid the risk of over chlorination.

Using your ProMasterTM VSD Eco-Series pump with

a Davey Salt Water Chlorinator:

Davey ChloroMatic and EcoSalt salt water chlorinators require a minimum

flow rate of 80 litres per minute (lpm) through the chlorinator cell for best

efficiency and cell life. Please refer to the performance graph below as a

reference for the flow in your pool and refer to the pressure indicated by the

gauge on the media or cartridge filter.

Ensure flow rate is sufficient to cover your chlorinator cell plates completely

at all times of operation.

0 5 10 15 20

0 50 100 150 200 250 300 350 400

Flow ( M / hr )

Total Head ( m )

Flow ( lpm )

ProMaster - PM200SV

Performance

Dial position: Back wash

Dial postion No. 10

Dial postion No. 9

Dial postion No. 8

Dial postion No. 7

Dial postion No. 6

Dial postion No. 5

Dial postion No. 4

Dial postion No. 3

Dial postion No. 2

Dial postion No. 1

Operating your Suction Pool Cleaner:

Before installing or purchasing a pool cleaner for use with your ProMasterTM

pool pump, it is important to know the minimum flow rates required for it to

operate effectively.

To operate a suction pool cleaner with your

ProMasterTM VSD Eco-Series pump:

1. Activate the High Flow setting (10) and allow the pump to fully prime by

running for around 2 minutes. You will know the pump is primed when

you can see a strong flow of water through the clear leaf basket lid.

2. When all air is expelled from the leaf basket, connect the pool cleaner

hose firmly into the skimmer plate or dedicated wall suction.

3. Select the speed setting that enables best performance from your suction

pool cleaner. Speed 3 to 7 should be ample for most cleaners, however if

the cleaner requires better performance, select speeds 7 to 10. A Davey

Frill-NeckWIZARD®suction pool cleaner is recommended to run between

speeds 3 to 6.

4. The cleaner should only be connected for as long as is required to clean

the surface of your pool. When cleaning is complete, disconnect the

cleaner and remove the skimmer plate from the skimmer box.

NOTE: To get optimum energy efciency from your ProMasterTM DO NOT keep

the suction pool cleaner connected when cleaning is not required.

5. Reactivate the most efficient speed setting for daily filtration. Speeds 1 to

4 is recommended.

Maintenance: Emptying the Strainer Basket

The strainer basket should be inspected frequently through the transparent

lid and emptied when a build up of rubbish is evident. The directions below

should be followed.

1. Switch off pump.

2. Unscrew the strainer basket lid anti-clockwise and remove.

3. Remove the strainer basket by lifting upwards from its housing.

4. Empty the trapped refuse from the basket. Hose out with water if

necessary.

NOTE: NEVER knock the plastic basket on a hard surface as it will cause damage.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Davey Wasserpumpe Handbücher

Davey

Davey CS Series Handbuch

Davey

Davey XF111SS Bedienungsanleitung

Davey

Davey PowerMaster Eco-Series Bedienungsanleitung

Davey

Davey jumbo floodfighter Bedienungsanleitung

Davey

Davey X201 Bedienungsanleitung

Davey

Davey TotalFlo TF117MS Bedienungsanleitung

Davey

Davey AS Series Bedienungsanleitung

Davey

Davey DynaDrive DD15-35NPT Bedienungsanleitung

Davey

Davey HS50-06 Bedienungsanleitung

Davey

Davey Weekender XP Bedienungsanleitung

Davey

Davey Dynaflo 60061R Bedienungsanleitung

Davey

Davey HM Series Bedienungsanleitung

Davey

Davey SJ35-04 Handbuch

Davey

Davey J Series Bedienungsanleitung

Davey

Davey WHISPER Series Bedienungsanleitung

Davey

Davey PowerMaster 250 Bedienungsanleitung

Davey

Davey 6200 Bedienungsanleitung

Davey

Davey VM Series Bedienungsanleitung

Davey

Davey E1P Series Bedienungsanleitung

Davey

Davey RainBank Evolution MkII Bedienungsanleitung

Davey

Davey RainBank KRBCABS1/20 Bedienungsanleitung

Davey

Davey CY/A Series Bedienungsanleitung

Davey

Davey Spa Power SP800 Bedienungsanleitung

Davey

Davey DynaDrive DD60-10 Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung

STA-RITE

STA-RITE ST33APP Bedienungsanleitung