Daytona DJS3GRY Montageanleitung

Visit our website at: http://www.harborfreight.com

Email our technical support at: [email protected]

Owner’s Manual & Safety Instructions

Save This Manual Keep this manual for the safety warnings and precautions, assembly,

operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the

back of the manual (or month and year of purchase if product has no number). Keep this manual and the

receipt in a safe and dry place for future reference. 22k

When unpacking, make sure that the product is intact

and undamaged. If any parts are missing or broken,

please call 1-888-866-5797 as soon as possible.

No portion of this manual or any artwork contained herein may be reproduced in

any shape or form without the express written consent of Harbor Freight Tools.

Diagrams within this manual may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the product described herein.

Tools required for assembly and service may not be included.

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

DJS6TBK Shown

DJS3TBK DJS3TOR DJS3TY

DJS3TGR DJS3TBL DJS3GRY

3-Ton

DJS6TBK DJS6TOR DJS6TY

DJS6TGR DJS6TBL DJS6GRY

6-Ton

DJS12TBK 12-Ton

Page 2 For technical questions, please call 1-888-866-5797. Jack Stand

Specifications

Model

DJS3TBK

DJS3TOR

DJS3TY

DJS3TGR

DJS3TBL

DJS3TGRY

DJS6TBK

DJS6TOR

DJS6TY

DJS6TGR

DJS6TBL

DJS6TGRY

DJS12TBK

Capacity 3 Tons (6,000 lb.)* 6 Tons (12,000 lb.)* 12 Tons (24,000 lb.)*

Height Range (Approximate) 11-3/8″ – 16-7/8″ 15-1/4″ – 24″ 19-5/8″ – 30-1/20″

*Evenly distributed across two Jack Stands.

IMPORTANT SAFETY INFORMATION

1. Study, understand, and follow all instructions

before operating this device.

2. Use only as an identical pair.

3. Maximum load capacity per identical pair shall not

exceed the rated capacity of the individual stand.

4. Use stands to support one end of a vehicle only.

5. Use only on a hard, level surface

capable of supporting the load.

6. Center load on saddle.

7. Locate saddles at vehicle manufacturer’s

designated support points.

8. Failure to heed these markings may result in

personal injury and/or property damage.

9. No alterations shall be made to this product.

10. Stands are not to be used to simultaneously

support both ends of a vehicle.

11. Wear ANSI-approved safety goggles and

heavy-duty work gloves during use.

12. Do not use for aircraft purposes.

13. Inspect before every use; do not use

if parts loose or damaged.

14. Examine Jack Stands for cracks or damage

before each use. Do not use if even a minor crack,

bend or other damage/deformation appears.

Discard Jack Stand if damaged or deformed.

15. Keep work area clean. Cluttered areas invite injuries.

16. Observe work area conditions.

Keep work area well lighted.

17. Keep children away. Children must

never be allowed in the work area.

18. Store idle equipment. When not in use, tools must

be stored in a dry location to inhibit rust. Always

lock up tools and keep out of reach of children.

19. There are certain applications for which this tool was

designed. Do not modify this tool and do not use this

tool for a purpose for which it was not intended.

20. Dress properly. Do not wear loose clothing or jewelry

as they can be caught in moving parts. Protective,

electrically non-conductive clothes and non-skid

footwear are recommended when working. Wear

restrictive hair covering to contain long hair.

21. Maintain tools with care. Keep tools clean for

better and safer performance. Follow instructions

for lubricating and changing accessories.

22. Stay alert. Watch what you are doing, use common

sense. Do not operate any tool when you are tired.

23. Do not operate tool if under the influence of

alcohol or drugs. Read warning labels on

prescriptions to determine if your judgment

or reflexes are impaired while taking drugs. If

there is any doubt, do not operate the tool.

24. Only use on proper surface. Only use the Jack

Stands on a dry, level, flat surface, which is free

of grease or debris. The surface to be used

must be capable of supporting the combined

weight of the vehicle and the Jack Stands.

25. The warnings, precautions, and instructions

discussed in this manual cannot cover all

possible conditions and situations that may occur.

The operator must understand that common sense

and caution are factors, which cannot be built into

this product, but must be supplied by the operator.

SAVE THESE INSTRUCTIONS.

Page 3

For technical questions, please call 1-888-866-5797.

Jack Stand

Assembly

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this

manual including all text under subheadings therein before set up or use of this product.

Note: For additional information regarding the parts listed in the following pages,

refer to the Assembly Diagram near the end of this manual.

1. Secure the chain to the jack stand by attaching the

split ring to the Hole near the Pawl. See Figure A.

2. Turn Post so that the teeth on its side face

the Pawl. Insert Post into the Base.

3. Bend Stop Tab in to secure the Post

into the Base. See Figure A.

CAUTION! Be alert to pinching hazard

when lowering the Post.

CAUTION! TO PREVENT INJURY: Before

using the Jack Stands, make sure the Post

cannot be pulled up and out of the Base.

4. Repeat Steps 1 through 4 with the other Jack Stand.

Stop Tab

Figure A

Split Ring

Split Ring Hole

Pawl

Page 4 For technical questions, please call 1-888-866-5797. Jack Stand

Operating Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this

manual including all text under subheadings therein before set up or use of this product.

WARNING! TO PREVENT SERIOUS INJURY: Use as matched pair to support one end of a vehicle only.

Supporting a Vehicle

1. Make sure the vehicle does not exceed the capacity

of the Jack Stands. Note: Check that the weight

is evenly distributed between the Jack Stands.

You must evenly distribute the weight or the

Jack Stands may fail, causing severe injury

or death. Only apply the load vertically.

WARNING! TO PREVENT SERIOUS INJURY: If a

vehicle drops on the Jack Stands (even if it is under

the weight capacity limit), the principle of “dynamic

loading” takes affect. The force of the weight

falling may cause the Jack Stands to fail. A vehicle

weighing much less than the Jack capacity may

cause the Jack Stands to fail if dropped on them.

Note: Do not move the Handle when the Jack

Stands are supporting a vehicle. The shear pin is

designed to shear in the event the user attempts to

move the Handle while supporting weight. If the pin

shears, do not use the Jack Stands again until the

shear pin is replaced by a qualified technician.

2. Examine Jack Stands for cracks or damage before

each use. Do not use if even a minor crack,

bend, or other damage/deformation appears.

Discard Jack Stand if damaged or deformed.

3. Raise the Handle on each Jack Stand

to completely lower the Post.

4. If your are raising only one end of the vehicle,

block the tires that remain on the ground.

5. Following the instructions in your floor jack

manual, raise your vehicle to just above the

minimum height of your Jack Stands.

6. Slide your Jack Stands to the proper position points

referred to in the vehicle owner’s manual. Make

sure the Jack Stands are on the same point on

each side of the vehicle. Move the Handle up,

and raise the Jack Stands until they are just below

the jack contact point on the vehicle. Center

the load on the Saddle of the Post. Release the

Handle so that ratchet catches on the Pawl.

7. Insert Locking Pin into the opening located next

to the Stop Tab. Secure the Locking Pin in place

by inserting the Safety Pin into the small hole

on the end of the Locking Pin. See Figure B.

Figure B

8. Gently lower the vehicle with the floor jack. It may

drop down a very small amount until the ratchet

catches on the Pawl. Repeat on other side.

WARNING! TO PREVENT SERIOUS INJURY:

Set both the Jack Stands to the same height.

9. Determine if the vehicle is stable. If not, raise

the vehicle and reposition the Jack Stands.

Removing the Jack Stands

1. Raise the vehicle with a floor jack to take

the load off of the Jack Stands.

2. Remove Safety Pin from the Locking Pin.

Remove the Locking Pin from the Base.

3. Raise the Handle on the Jack

Stands and lower the Posts.

4. Remove the Jack Stands. Use the floor jack

to safely lower the vehicle to the ground.

WARNING! TO PREVENT SERIOUS INJURY:

Do not use Jack Stands as a permanent stand for

the vehicle. Use them only while making repairs,

then immediately lower vehicle to the ground.

Locking

Safety Pin

Hole

Page 5

For technical questions, please call 1-888-866-5797.

Jack Stand

Maintenance and Servicing

Procedures not specifically

explained in this manual must be

performed only by a qualified technician.

TO PREVENT SERIOUS INJURY FROM TOOL

FAILURE:

Do not use damaged equipment.

If abnormal noise or vibration occurs, have

the problem corrected before further use.

1. Periodically clean the bottom of the Bases and

top of Posts of any dirt, grease, or debris.

2. Before each use, inspect the general condition

of the Jack. Check for broken, cracked, or bent

parts, loose or missing parts, and any condition

that may affect the proper operation of the

product. Do not use damaged equipment.

Discard Jack Stand if damaged or deformed.

3. Periodically lubricate release handle pivot points.

Page 6 For technical questions, please call 1-888-866-5797. Jack Stand

Parts List and Assembly Diagram

Part Description Qty

1 Post 1

2 Split Ring 1

3 Locking Pin 1

4 Handle Grip 1

5 Handle 1

6 Base 1

7 Pawl 1

8 Pin 1

9 Safety Pin 1

Page 7

For technical questions, please call 1-888-866-5797.

Jack Stand

Record Product’s Serial Number Here:

Note: If product has no serial number, record month and year of purchase instead.

Note: Some parts are listed and shown for illustration purposes only, and are not available

individually as replacement parts. Parts may not be interchangeable.

Specify UPC number when ordering:

3-Ton Orange (58346): UPC 193175438584 6-Ton Orange (58350): UPC 193175438546

3-Ton Yellow (58345): UPC 193175438591 6-Ton Yellow (58349): UPC 193175438539

3-Ton Green (58347): UPC 193175438492 6-Ton Green (58351): UPC 193175438515

3-Ton Blue (58344): UPC 193175438607 6-Ton Blue (58348): UPC 193175438577

3-Ton Slate Grey (70593): UPC 193175501189 6-Ton Slate Grey (70594): UPC 193175501196

3-Ton Black (58343): UPC 193175439260 6-Ton Black (58342): UPC 193175439383

12-Ton Black (58341): UPC 193175439246

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE

TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF

ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR

SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR

EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND

LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS

OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER

INSTALLATION OF REPLACEMENT PARTS THERETO.

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,

and warrants to the original purchaser that this product is free from defects in materials and workmanship

for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly

or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal

activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable

for death, injuries to persons or property, or for incidental, contingent, special or consequential damages

arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or

consequential damages, so the above limitation of exclusion may not apply to you. This warranty is expressly

in lieu of all other warranties, express or implied, including the warranties of merchantability and fitness.

To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof

of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the

defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we

cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we

determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must

bear the cost of returning the product.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

26677 Agoura Road • Calabasas, CA 91302 • 1-888-866-5797

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Daytona Rack & Stand Handbücher

Daytona

Daytona 57745 Montageanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung