DEEP SEA ELECTRONICS DSEE400 Bedienungsanleitung

TYPICAL WIRING DIAGRAM

NOTE: To meet UL requirements, fuse the module supply at 167% of supply current.

DEEP SEA ELECTRONICS

DSEE400 Installation Instructions

053-180

ISSUE 5

ACCESSING THE FRONT PANEL EDITOR

•Ensure the engine is at rest and the module is in STOP mode by pressing the

Stop/Reset button.

•Press and hold the Stop/Reset and Auto buttons simultaneously.

•If a module security PIN has been set, the PIN number request is then shown:

•Press the Auto button, the first ‘#’ changes to ‘0’. Press Up or Down buttons to adjust it to the

correct value.

•Press and hold the Up button when the first digit is correctly entered. The digit you have just entered will

now show ‘#’ for security.

•Repeat this process for the other digits of the PIN number. Press and hold the Down button if previous digits

need to be edited. Press the Auto button to finish editing the PIN.

•Press the Auto button to check the PIN for validity. If the number is not correct, the PIN must be re-entered.

•If the PIN has been successfully entered (or the module PIN has not been

enabled), the editor is displayed:

EDITING A PARAMETER

•Enter the editor as described.

•Press and hold the Up or Down buttons to cycle to the section you wish to view/change.

•Press the Up or Down buttons to select the parameter you wish to view/change within the currently

selected section.

•To edit the parameter, press the Auto button to enter edit mode. The parameter begins to flash to indicate

that you are editing the value.

•Press the Up or Down buttons to change the parameter to the required value.

•Press the Auto button to save the value. The parameter ceases flashing to indicate that it has been saved.

•To exit the editor and save the changes, press and hold the Auto button.

•To exit the editor and not save the changes, press and hold the Stop/Reset button.

NOTE: The editor is exited after 5 minutes of inactivity to ensure security.

NOTE: The PIN number is automatically reset when the editor is exited (manually or automatically) to

ensure security.

NOTE: More comprehensive module configuration is possible using the DSE Configuration Suite PC

Software, refer to DSE publication 057-251 DSEE400 Configuraiton Suite PC Software Manual.

Deep Sea Electronics Ltd.

Tel:+44 (0)1723 890099

Email: support@deepseaelectronics.com

Web: www.deepseaelectronics.com

Deep Sea Electronics Inc.

Tel: +1 (815) 316 8706

Email: USASupport@deepseaelectronics.com

Web: www.deepseaelectronics.com

FRONT PANEL EDITOR PARAMETERS

Section

Parameter As Shown On Display

Value

Display

Contrast

66 %

Backlight Level

100 %

Language

English

Current Date and Time

Day:month:year,

hour:minute:seconds

Engine

Oil Pressure Low Shutdown (If Set)

1.03 bar, kPa, psi

Oil Pressure Low Pre Alarm (If Set)

1.24 bar, kPa, psi

Coolant Temperature High Pre Alarm

(If Set)

90 ºC, ºF

Coolant Temp High Controlled

Shutdown (If Set)

92 ºC, ºF

Coolant Temperature High Shutdown

(If Set)

95 ºC, ºF

Pre Heat Temperature (If Set)

50 ºC, ºF

Pre Heat Timer

0 h 0 m 0 s

Post Heat Temperature (If Set)

50 ºC, ºF

Post Heat Timer

0 h 0 m 0 s

Under Speed Shutdown

Active, Inactive

Under Speed Shutdown

1200 rpm

Under Speed Warning

Active, Inactive

Under Speed Warning

1260 rpm

Over Speed Warning

Active, Inactive

Over Speed Warning

1650 rpm

Over Speed Shutdown

1710 rpm

Overspeed Overshoot

Battery Under Voltage Warning

Active, Inactive

Battery Under Voltage Warning

10.0v

Battery Under Voltage Warning Delay

0h 1m 0s

Battery Over Voltage Warning

Active, Inactive

Battery Over Voltage Warning

30.0v

Battery Over Volts Warning Delay

0h 1m 0s

Charge Alternator Failure Pre-Alarm

Active, Inactive

Charge Alternator Failure Pre-Alarm

6.0v

Charge Alternator Failure Pre-Alarm

Delay

0h 0m 5s

Charge Alternator Failure Shutdown

Active, Inactive

Charge Alternator Failure Shutdown

4.0v

Charge Alternator Shutdown Delay

0h 0m 5s

Battery Under Voltage Warning

Active, Inactive

Battery Under Voltage Warning

10.0v

Battery Under Voltage Warning Delay

0h 1m 0s

Battery Over Voltage Warning

Active, Inactive

Battery Over Voltage Warning

30.0v

Battery Over Volts Warning Delay

0h 1m 0s

Charge Alternator Failure Pre-Alarm

Active, Inactive

Charge Alternator Failure Pre-Alarm

6.0v

Charge Alternator Failure Pre-Alarm

Delay

0h 0m 5s

Charge Alternator Failure Shutdown

Active, Inactive

Charge Alternator Failure Shutdown

4.0v

Charge Alternator Shutdown Delay

0h 0m 5s

Clutch

Clutch Disengage Low Speed

0 rpm

Control

Clutch Engage Speed

0 rpm

Clutch Disengage High Speed

8000 rpm

Clutch Re-Engage

0 rpm

Clutch Disengage Low Speed

0 rpm

PLC

PLC Watched Item (1-16)

[PLC value] units

Instruments

Section

Parameter As Shown On Display

Value

Speed

Cranking Speed

0 rpm

Settings

Warming Speed

0 rpm

Idle Speed

0 rpm

Priming Speed

0 rpm

DPF Regeneration Speed*

Active, Inactive

DPF Regeneration Speed*

0 rpm

Cooldown Speed

0 rpm

Speed

Min Speed

0 rpm

Control

Default Running Speed

0 rpm

Max Speed

0 rpm

Fixed Running Speed

0 rpm

Selectable Speed 1

0 rpm

Selectable Speed 2

0 rpm

Selectable Speed 3

0 rpm

Selectable Speed 4

0 rpm

Linear Min Sensor Value

[Val] <user/units>

Linear Max Sensor Value

[Val] <user/units>

Linear Speed at Min

0 rpm

Linear Speed at Max

0 rpm

Emptying Speed

0 rpm

Filling Speed

0 rpm

Maintain Empty Running Speed

0 rpm

Maintain Empty Emptying Speed

0 rpm

Maintain Empty Setpoint

[Val] <user/units>

Maintain Empty Deadband

[Val] <user/units>

Maintain Fill Running Speed

0 rpm

Maintain Fill Filling Speed

0 rpm

Maintain Fill Setpoint

[Val] <user/units>

Maintain Fill Deadband

[Val] <user/units>

Engine Start Value

[Val] <user/units>

Engine Stop Value

[Val] <user/units>

Maintenance

Maintenance PIN protect

Active, Inactive

Maintenance Alarm 1

10h

Maintenance Alarm 2

10h

Maintenance Alarm 3

10h

Maintenance Alarm 4

10h

Maintenance Alarm 5

10h

Maintenance Alarm 6

10h

Maintenance Alarm 7

10h

Maintenance Alarm 8

10h

Maintenance Alarm 9

10h

Maintenance Alarm 10

10h

CAN

CAN Terminator Active

Active, Inactive

DPF Auto Regen Inhibit*

Active, Inactive

DPF Manual Regen*

Active, Inactive

DPF Manual Regen Cancel*

Active, Inactive

Flexible

Flexible Sensor (A-G) Low Alarm

Active, Inactive

Sensors

Flexible Sensor (A-G) Low Alarm

[value] <unit>

Flexible Sensor (A-G) Low Pre-Alarm

Active/Inactive

Flexible Sensor (A-G) Low Pre-Alarm

[value] <unit>

Flexible Sensor (A-G) High Pre-Alarm

Active/Inactive

Flexible Sensor (A-G) High Pre-Alarm

[value] <unit>

Flexible Sensor (A-G) High Alarm

Active/Inactive

Flexible Sensor (A-G) High Alarm

[value] <unit>

Timers

LCD Page Timer

0h 5m 0s

LCD Scroll Delay

0h 0m 2s

Start Delay Off load

Start Delay On load

Start Delay Telemetry

Delayed Engine Start

0h 0m 30s

Cranking

0m 10s

Cranking Rest

0m 10s

Section

Parameter As Shown On Display

Value

Timers

Safety On Delay

0m 10s

Cont.…

Smoke Limiting

0h 0s

Smoke Limiting Off

0h 0s

Warming

0h 0m 0s

Return Delay

0h 0m 30s

Cooling

0h 1m 0s

Cooling at Idle

0h 1m 0s

Failed To Stop Delay

0m 30s

Delayed Engine Stop

0h 0m 30s

Engine Speed Transient Delay

0.0s

Priming Delay

0h 0m 30s

Selectable Speed Transfer Delay

0m 0.2s

DPF Ramp*

Scheduler

Schedule

Active, Inactive

Schedule Period

Wkly/Mthly (If Active)

Schedule Time & Date Selection (1-8)

See Editing A

Parameter

1 Schedule

Off Load / On Load /

Auto start inhibit

Week 1 (If Monthly selected)

Wk1, Wk2, Wk3, Wk4

00:00

Run Time

00:00

M T W T F S S

Select day

Active

Active Config Select

Configuration

*Electronic Engines Only

ACCESSING THE SPEED CONTROL EDITOR

•Ensure the engine is at rest and the module is in STOP mode by

pressing the Stop/Reset button.

•Navigate to the Active Configuration screen in the Engine section of the

module’s display.

•Press and hold the Up and Down buttons simultaneously to

enter the editor, no PIN is required.

•Edit the parameters as described overleaf in the Editing a Parameter

section.

DIMENSIONS AND MOUNTING

For flat surface mounting in a Type 1 enclosure to meet UL requirements

DIMENSIONS

189 mm x 125 mm x 54 mm

(7.5” x 4.9” x 2.1”)

MOUNTING HOLE SPACING

165 mm x 68 mm

(6.5” x 2.7”)

PANEL CUTOUT

148 mm x 112 mm

(5.8” x 4.4”)

MOUNTING HOLE

DIAMETER

Suitable for M4

(5/32” diameter)

CONNECTORS & WIRING HARNESS

Details

DSE Part

Number

Manufacturer’s

Part Number

Manufacturer

Connector A

007-850

DT16-18SA-K004

Deutsch

Connector C

007-851

DT16-18SC-K004

Deutsch

1.2 m Wiring Harness

Complete With

Connector A & C.

007-852

DSE

Andere DEEP SEA ELECTRONICS Steuerungssystem Handbücher

DEEP SEA ELECTRONICS

DEEP SEA ELECTRONICS DSE8610 MKII Bedienungsanleitung

DEEP SEA ELECTRONICS

DEEP SEA ELECTRONICS DSE860 Bedienungsanleitung

Beliebte Steuerungssystem Handbücher anderer Marken

Pentair Pool Products

Pentair Pool Products Compool Bedienungsanleitung

ComfortNET

ComfortNET CTK04 Bedienungsanleitung

Fireye

Fireye InSight II 95DSS3 Bedienungsanleitung

CAME

CAME G3000 Bedienungsanleitung

Idemia

Idemia MorphoAccess VP MD Bedienungsanleitung

Axis

Axis P1445-LE-3 Bedienungsanleitung

HEIDENHAIN

HEIDENHAIN TNC 150 B Bedienungsanleitung

CNC-Step

CNC-Step High-Z T-Series Bedienungsanleitung

Doosan

Doosan DVF Series Bedienungsanleitung

Honeywell

Honeywell KAP 140 Bedienungsanleitung

Honeywell

Honeywell vk41 series Bedienungsanleitung

AirBench

AirBench FPW Installationsanleitung

Cypress

Cypress HHR-3160 Bedienungsanleitung

CAME

CAME GLT40AOS Bedienungsanleitung

Zonex

Zonex GEN II -VVT Benutzerhandbuch

Altronics

Altronics K 9650 Bedienungsanleitung

micro-trak

micro-trak RoadMaster Bedienungsanleitung

micro-trak

micro-trak Calc-An-Acre II Bedienungsanleitung