3.4.8 Sch.SP01 schedule point select, press IP to select district and schedule points:
01~08,11~16,21~26,31~36,41~46, press Light to into setting.
3.4.8.1 Lock weekday select (can't change when parameter blinking).
3.4.8.2 IP Schedule hour setting (0~23).
3.4.8.3 IP Schedule minute setting (0~59).
3.4.8.4 Mode Schedule points and operation setting (schedule time is no display
when no schedule).
3.4.8.5 Schedule setting (0~35.0)
3.4.8.6 POWER Sechedule power (On/Off)
3.4.8.7 Light Confirm setting.
3.4.8.8 Fan Cancel setting / return to 3.4.8 schedule point selection.
5
5
5 Max limit heating setting(HS)/ Min limit cooling setting
(CS)/ Temp. calibration(OT).
5
5
3.6 Link display
3.6.1 Product model and connection check in 20 seconds after power on.
3.6.2 If the IP has connected successfully, IP address is able to select, even if any
connection failure.
3.6.3 To remove the display of IP connection interruption, press POWER button to remove
link status.
4. Failure Elimination :
4.1 E1 Sensor failure.
4.2 EE Memory failure.
4.3 EC Abnormal communication of power board (no any linking situation of power board).
4.4 FA Exceeding temperature alarm.
4.5 PN location is still able to be selected, even if there is any alarm occurred (except EC).
No any button pressed in 5 seconds, it comes to display the status of alarmed PN.
4.6 If there are multi-PN in alarm simultaneously, display shows each alarmed PN in turns for
5 seconds.
4.7 LCD backlight is illuminated constantly when under failure alarm.
4.8 When in failure alarm, buzzer ON for 0.8 seconds and OFF for another 0.8 seconds.
3. All group control mode (AC=ON)
3. .1 Under this mode, can't into district mode.
3. .2 Under this mode, can't set the
3. .3 Under this mode, fan address show AC. When change fan, show fan IP 2 seconds.
3. .4 Under this mode, operated model/ fan speed/ setpoint/ lock/ power are the controlled
command for all fan.
3.2.8 Min limit cooling setting (DEI-758FPN / 201NAHU / 201NVAV)
When DEI-758FPN/ 201NAHU / 201NVAV in OFF status, press for 3 seconds
to into min limit cooling setting (show CS) and adjust by .
Setting range 0 35 ; Under setting status, press IP into AL-CS setting.
After complete setting, press Light to confirm or press Fan to cancel.
3.2.9 Temperature calibration setting (DEI-758FPN/201NAHU/201NVAV)
OFF status in single fan, press Fan for 3 seconds into temperature calibration
(Ot) mode, and press to adjust value, setting range -8 8 . Press Light to
confirm or press Fan to cancel after setting.
3.2.10 Auto air conditioning while power off: under this mode, the display shows the room
temperature and it blinks.
3.3 Group control function press IP for 3 seconds to into or exist group status (fan address
shows all district (AL) or district A1~A4.
3.3.1 Press IP to select district, can select AL for all districts, or A1~A4 district (only fans
in district accept command).
3.3.2 Under group control, press Power to set all districts (district) power status.
3.3.2.1 Show Pr On, is meaning set all districts (district) start operating.
3.3.2.2 Show Pr OF, is meaning set all districts (district) stop operating.
3.3.2.3 The condition of group controller switch on power
Group commend switch off controller power in advance.
3.3.3 Under the group control, press Mode to set all districts (district) group mode status.
3.3.4 Under the group control, press Fan to set all districts (district) group fan speed status.
3.3.5 Under the group control, press Lock to set all districts (district) group lock status.
3.3.6 Under the group control, press to set all districts (district) group set temp.
3.3.7 Under the group control, the separated line is blinking is meaning Group Control
setting is waiting confirm; press Light to confirm or IP to cancel setting.
3.3.8 Under the AL-HS, press to set all districts Max limit heating setting.
3.3.9 Under the AL-CS, press to set all districts Min limit cooling setting.
3.4 Main control parameter setting: under normal mode, press Light for 3 seconds to into /
exist main control parameter setting; in the parameter,
press Mode to select below parameter.
3.4.1 IP (IP setting) press IP to select main controller IP=01~99, press Light to
confirm, press Fan to cancel.
3.4.2 br (Baud rate setting) press IP to select baud rate 4800~1152, press Light to
confirm, press Fan to cancel.
3.4.3 Pr (Parity bite setting) press IP to select n81/O81, press Light to confirm setting,
press Fan to cancel.
3.4.4 AC (All group control) press IP to select AC ON/OF, press Light to confirm
setting, press Fan to cancel.
3.4.5 rtc (Alarm clock setting) setting DEI-758SCN time (retain timing in 72 hours after
power off)
3.4.5.1 Lock set weekday (Sun~Sat).
3.4.5.2 IP set hour (0~23).
3.4.5.3 IP set min (0~59).
3.4.5 4 Light confirm setting Fan cancel setting.
3.4.6 Ar district setting, press IP to select IP1~63, press IP to set district (0A~4A),
press Light to confirm, press Fan to cancel.
3.4.7 Sch.dE weekday schedule, press IP to select weekday operation schedule,
press Light to confirm setting, press Fan to cancel.
