Dell POWER VAULT 130T LIBRARY 130T Bedienungsanleitung

www.dell.com

Dell PowerVault™130T Library

DRIVE INSTALLATION GUIDE

www.dell.com

Dell PowerVault™130T Library

DRIVE INSTALLATION GUIDE

____________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Computer Corporation

is strictly forbidden.

Trademarks used in this text: Dell, the DELL logo are registered trademarks, and PowerVault is a trade-

mark of Dell Computer Corporation.

Other trademarks and trade names may be used in this document to refer to either the entities claiming

the marks and names or their products. Dell Computer Corporation disclaims any proprietary interest

in trademarks and trade names other than its own.

October 1998 5085D Vendor P/N 61839

Drive Tray Conversion Instructions 1

PowerVault 130T Drive

Installation Instructions

DLT Drive Tray Assembly

These installation instructions describes how to remove, install and configure a DLT Drive

Tray Assembly into the PowerVault 130T.

Before beginning this procedure be sure to take note of your drive configuration. You may

need this later to reconfigure your new or additional drives.

NOTE: Tape drives are hot swappable, meaning they can be removed and replaced without

powering off the library or interrupting its operations. Hot swapping should only be

performed by trained technicians.

WARNING: HIGH VOLTAGE! DO NOT TOUCH any components on the power

supply located within the electronics module or on the drive trays. Live voltage

could be present even though the unit is powered off. (Refer to U03 in Safety

Booklet)

Removing the DLT Drive Tray Assembly

CAUTION: If the drives are daisy-chained do not disconnect them from the bus

without stopping all data processing on the channel. Before disconnecting the

external SCSI cables, make sure there is no activity on the SCSI bus. The host

must be quiesced, meaning that there is no activity on the SCSI bus. Do not

disconnect a hot bus. Any third party software must be quiesced. All signals

must be terminated at each end of the SCSI bus.

Follow the instructions below to remove a DLT Drive Tray Assembly. The tape drives are

located in the tape drive slots at the left rear of the library.

1. Loosen the three thumbscrews from the hinged door at the rear of the library and

open the door.

2 Drive Tray Assembly Conversion Instructions

Figure 1. Back Vziew of Drive Tray Assembly

Back View of Drive Tray Assembly

Item

Number

Parts Description

1TapeDrive

2 Thumbscrew (3x)

3 Hinged Door

Drive Tray Conversion Instructions 3

Figure 2. Interface Connection and Power

Interface Connection and Power

2. Disconnect the power cable from the tape drive.

CAUTION: Disconnect the tape drive interface cable (P980-P983), as described

in the next step, before removing the tape drive. Make sure the cable is out of

the tape drive bay by removing it from the rectangular hole to prevent the

cable from being damaged.

3. Disconnect the tape drive interface cable from the tape drive.

NOTE: The tape drive interface cable (P980-P983) markings face the rear of the tape drive.

Note this orientation when reinstalling the drive interface cable. The connector is keyed but

it is still possible to insert it incorrectly.

4. Disconnect the SCSI cable connectors and/or terminator from the rear of the drive.

Save the old terminator, if any.

Item

Number

Parts Description

1 PowerReceptacle

2 Tape Drive Interface Connector

3 Thumbscrew (2x)

4 Drive Tray Assembly Conversion Instructions

5. Loosen the two thumbscrews at the rear of the drive assembly.

6. Using both hands, remove the drive assembly from the drive slot, placing it on a flat,

stable surface.

WARNING: DO NOT apply power to the tape drive when it is outside of the

drive slot. To avoid damaging the drive, do not operate the load latch manually

while the drive is outside the library.

Replacing the Tape Drive Tray assembly

1. If you are replacing your drive with a new drive, unpack the assembly and inspect it for

damage such as bent, broken, or loose parts.

•Verify that the tape drive model and serial numbers match those on the shipping

invoice. Labels on top of the drive show either DLT4000 or DLT7000.

•Verify that required cables are present.

•Report any damaged or missing items to your Dell representative.

WARNING: Do not touch any components on the power supply. Live voltage

could be present even though the unit is powered off.

Figure 3. Setting TermPwr

Drive Tray Conversion Instructions 5

Setting TermPwr

2. To check terminator power (TERMPWR), remove the two power supply cover screws

using a Torx driver with a T-15 bit, and lift the cover (pulling forward slightly) enough to

see the jumpers. For safety, do not remove the cover completely.

3. Set the TERMPWR on or off (enabled or disabled) on the new tape drive to match the

drive you are replacing. The figure shows the right side of the tape drive (as you face

its front). The drives are shipped from the factory with TERMPWR on.

•Install the jumper on the pins as shown to set TERMPWR on.

•Remove the jumper from the pins to set TERMPWR off. You may store the

jumper by placing it on one pin only.

4. Return the power supply cover to its previous position and reinstall the two screws

holding it in place.

CAUTION: When sliding the drive into its bay, make sure the tape drive

interface cable (with connectors P980-P983) is out of the way. Do not force the

tape drive into the drive slot.

5. Slide the drive into its slot, being careful not to catch or crush any cables.

6. Tighten the two thumbscrews on the back of the tape drive.

CAUTION: efore connecting the external SCSI cables, make sure there is no

activity on the SCSI bus. Do not connect to a hot bus. Any third party software

must be quiesced. All signals must be terminated at each end of the SCSI bus.

Do not mix single-ended and differential terminators.

Item

Number

Parts Description

1 Power Supply Cover

2 Power Supply Cover Screw Location

(2x)

3 TermPwr Jumper, second pair of pins

from end of connector (shown enabled)

6 Drive Tray Assembly Conversion Instructions

Figure 4. Connecting the SCSI cable

Connecting the SCSI cable

CAUTION: The tape drive interface cable (P980-P983) marking faces the rear of

the tape drive. Note this orientation when reinstalling. The connector is keyed

but it is still possible to insert it incorrectly.

7. Connect the tape drive interface cable (P983) to the tape drive interface connector on

the tape drive.

8. Connect the tape drive power cable to the tape drive.

Item

Number

Parts Description

1 Tape Drive Interface Cable (P983)

2 Thumbscrew (2x)

3 SCSI Connector (2x Per Drive)

4Drive0

Drive

Number

Drive Interface Connector

Drive 0 P983

Drive 1 P982

Drive 2 P981

Drive 3 P980

Andere Handbücher für POWER VAULT 130T LIBRARY 130T

Andere Dell Computerzubehör Handbücher

Dell

Dell OptiPlex 5050 Tower Bedienungsanleitung

Dell

Dell OptiPlex 5080 Bedienungsanleitung

Dell

Dell OptiPlex 3080 Small Form Factor Cable Cover Bedienungsanleitung

Dell

Dell Precision 5820 Tower D02T Bedienungsanleitung

Dell

Dell Precision Dual USB Type-C Thunderbolt 3 Dock Bedienungsanleitung

Dell

Dell LATITUDE PRX Benutzerhandbuch

Dell

Dell Inspiron 600m Bedienungsanleitung

Dell

Dell KM632 Bedienungsanleitung

Dell

Dell K12A Bedienungsanleitung

Dell

Dell OptiPlex 3080 Tower Bedienungsanleitung

Dell

Dell DL1000 Bedienungsanleitung

Dell

Dell OptiPlex 3080 Bedienungsanleitung

Dell

Dell Pro Wireless KM5221W Bedienungsanleitung

Dell

Dell EXTCDR-1 Bedienungsanleitung

Dell

Dell OptiPlex 3080 Tower Bedienungsanleitung

Dell

Dell Wyse 3010 Bedienungsanleitung

Dell

Dell AC Adapter Safety Installations- und Betriebsanleitung

Dell

Dell OptiPlex 5090 Small Form Factor Bedienungsanleitung

Dell

Dell Precision Compact Bedienungsanleitung

Dell

Dell Inspiron 3500 Bedienungsanleitung

Dell

Dell KM714 Bedienungsanleitung

Dell

Dell PN556W Bedienungsanleitung

Dell

Dell KM713 Bedienungsanleitung

Dell

Dell OptiPlex 5090 Tower Bedienungsanleitung

Beliebte Computerzubehör Handbücher anderer Marken

Motorola

Motorola ATRIX Bedienungsanleitung

HP USB Media Docking Station Bedienungsanleitung

Cherry

Cherry B.UNLIMITED 3.0 Bedienungsanleitung

Logitech

Logitech IO2 Bedienungsanleitung

ARM

ARM DSTREAM-ST Bedienungsanleitung

Bartec

Bartec TC 7 Series Bedienungsanleitung

Philips

Philips SPC3540 Bedienungsanleitung

Logitech

Logitech mk220 Bedienungsanleitung

SilverStone

SilverStone LC02 Bedienungsanleitung

Flexispot

Flexispot ML2B Bedienungsanleitung

Hamlet

Hamlet UNIVERSAL COVER 101 KBT2 Bedienungsanleitung

Adam Equipment

Adam Equipment RS-485 Bedienungsanleitung

Vivo

Vivo MOUNT-KB05-4DW Bedienungsanleitung

Kvaser

Kvaser Memorator Professional Bedienungsanleitung

DRC

DRC D-Imaging Bedienungsanleitung

Sven

Sven Base 305 сombo Bedienungsanleitung

Hama

Hama 108310 Bedienungsanleitung

SpeechWare

SpeechWare FlexyMike FMK03 Bedienungsanleitung